[U-Boot] [PATCH v2 27/27] x86: Add a README.x86 for U-Boot on x86 support

Simon Glass sjg at chromium.org
Fri Dec 12 04:31:14 CET 2014


On 9 December 2014 at 07:50, Bin Meng <bmeng.cn at gmail.com> wrote:
> Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
>
> ---
>
> Changes in v2:
> - Remove the 'make menuconfig' in the crownbay build instructions
> - Indicate all the binary blobs should be put in the board directory
>
>  doc/README.x86 | 126 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 126 insertions(+)
>  create mode 100644 doc/README.x86

Acked-by: Simon Glass <sjg at chromium.org>

>
> diff --git a/doc/README.x86 b/doc/README.x86
> new file mode 100644
> index 0000000..902aa7e
> --- /dev/null
> +++ b/doc/README.x86
> @@ -0,0 +1,126 @@
> +#
> +# Copyright (C) 2014, Simon Glass <sjg at chromium.org>
> +# Copyright (C) 2014, Bin Meng <bmeng.cn at gmail.com>
> +#
> +# SPDX-License-Identifier:     GPL-2.0+
> +#
> +
> +U-Boot on x86
> +=============
> +
> +This document describes the information about U-Boot running on x86 targets,
> +including supported boards, build instructions, todo list, etc.
> +
> +Status
> +------
> +U-Boot supports running as a coreboot [1] payload on x86. So far only link
> +(Chromebook pixel) has been tested, but it should work with minimal adjustments
> +on other x86 boards since coreboot deals with most of the low-level details.
> +
> +U-Boot also supports booting directly from x86 reset vector without coreboot,
> +aka raw support or bare support. Currently Google Chromebook link and Intel
> +Crown Bay board support running U-Boot 'bare metal'.
> +
> +As for loading OS, U-Boot supports directly booting a 32-bit or 64-bit Linux
> +kernel as part of a FIT image. It also supports a compressed zImage.
> +
> +Build Instructions
> +------------------
> +Building U-Boot as a coreboot payload is just like building U-Boot for targets
> +on other architectures, like below:
> +
> +$ make coreboot-x86_defconfig
> +$ make all
> +
> +Building rom version U-Boot (hereafter referred to as u-boot.rom) is a little
> +bit tricky, as generally it requires several binary blobs which are not shipped
> +in the U-Boot source tree. Due to this reason, the u-boot.rom build is not
> +turned on by default in the U-Boot source tree. Firstly, you need turn it on
> +by uncommenting the following line in the main U-Boot Makefile:
> +
> +# ALL-$(CONFIG_X86_RESET_VECTOR) += u-boot.rom
> +
> +Google Chromebook link specific instructions:
> +
> +Firstly, you need the following binary blobs:
> +
> +* descriptor.bin - Intel flash descriptor
> +* me.bin - Intel Management Engine
> +* mrc.bin - Memory Reference Code, which sets up SDRAM
> +* video ROM - sets up the display
> +
> +You can get these binary blobs by:
> +
> +$ git clone http://review.coreboot.org/p/blobs.git
> +$ cd blobs
> +
> +Find the following files:
> +
> +* ./mainboard/google/link/descriptor.bin
> +* ./mainboard/google/link/me.bin
> +* ./northbridge/intel/sandybridge/systemagent-ivybridge.bin
> +
> +The 3rd one should be renamed to mrc.bin.
> +As for the video ROM, you can get it here [2].
> +Make sure all these binary blobs are put in the board directory.
> +
> +Now you can build U-Boot and obtain u-boot.rom:
> +
> +$ make chromebook_link_defconfig
> +$ make all
> +
> +Intel Crown Bay specific instructions:
> +
> +U-Boot support of Intel Crown Bay board [3] relies on a binary blob called
> +Firmware Support Package [4] to perform all the necessary initialization steps
> +as documented in the BIOS Writer Guide including initialization of the CPU,
> +memory controller, chipset and certain bus interfaces.
> +
> +Downalod the Intel FSP for Atom E6xx series and Platform Controller Hub EG20T,
> +install it on your host and locate the FSP binary blob. Note this platform
> +also requires a Chipset Micro Code (CMC) state machine binary to be present in
> +the SPI flash where u-boot.rom resides, and this CMC binary blob can be found
> +in this FSP package too.
> +
> +* ./FSP/QUEENSBAY_FSP_GOLD_001_20-DECEMBER-2013.fd
> +* ./Microcode/C0_22211.BIN
> +
> +Rename the first one to fsp.bin and second one to cmc.bin and put them in the
> +board directory.
> +
> +Now you can build U-Boot and obtaim u-boot.rom
> +
> +$ make crownbay_defconfig
> +$ make all
> +
> +CPU Microcode
> +-------------
> +Modern CPU usually requires a special bit stream called microcode [5] to be
> +loaded on the processor after power up in order to function properly. U-Boot
> +has already integrated these as hex dumps in the source tree.
> +
> +Driver Model
> +------------
> +x86 has been converted to use driver model for serial and GPIO.
> +
> +Device Tree
> +-----------
> +x86 uses device tree to configure the board thus requires CONFIG_OF_CONTROL to
> +be turned on. Not every device on the board is configured via devie tree, but
> +more and more devices will be added as time goes by. Check out the directory
> +arch/x86/dts/ for these device tree source files.
> +
> +TODO List
> +---------
> +- MTRR support (for performance)
> +- Audio
> +- Chrome OS verified boot
> +- SMI and ACPI support, to provide platform info and facilities to Linux
> +
> +References
> +----------
> +[1] http://www.coreboot.org
> +[2] http://www.coreboot.org/~stepan/pci8086,0166.rom
> +[3] http://www.intel.com/content/www/us/en/embedded/design-tools/evaluation-platforms/atom-e660-eg20t-development-kit.html
> +[4] http://www.intel.com/fsp
> +[5] http://en.wikipedia.org/wiki/Microcode
> --
> 1.8.2.1
>


More information about the U-Boot mailing list