[U-Boot] [PATCH 07/26] mpc8xx: remove R360MPI board support
Masahiro Yamada
yamada.m at jp.panasonic.com
Mon Dec 15 15:26:12 CET 2014
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
Cc: Wolfgang Denk <wd at denx.de>
---
arch/powerpc/cpu/mpc8xx/Kconfig | 4 -
arch/powerpc/cpu/mpc8xx/cpu_init.c | 1 -
board/r360mpi/Kconfig | 9 -
board/r360mpi/MAINTAINERS | 6 -
board/r360mpi/Makefile | 8 -
board/r360mpi/flash.c | 468 -------------------------------------
board/r360mpi/pcmcia.c | 232 ------------------
board/r360mpi/r360mpi.c | 403 --------------------------------
board/r360mpi/u-boot.lds | 89 -------
configs/R360MPI_defconfig | 3 -
doc/README.scrapyard | 1 +
drivers/video/mpc8xx_lcd.c | 25 --
include/commproc.h | 4 -
include/configs/R360MPI.h | 464 ------------------------------------
include/pcmcia.h | 2 -
15 files changed, 1 insertion(+), 1718 deletions(-)
delete mode 100644 board/r360mpi/Kconfig
delete mode 100644 board/r360mpi/MAINTAINERS
delete mode 100644 board/r360mpi/Makefile
delete mode 100644 board/r360mpi/flash.c
delete mode 100644 board/r360mpi/pcmcia.c
delete mode 100644 board/r360mpi/r360mpi.c
delete mode 100644 board/r360mpi/u-boot.lds
delete mode 100644 configs/R360MPI_defconfig
delete mode 100644 include/configs/R360MPI.h
diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
index 37ee5f6..4e67ff2 100644
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ b/arch/powerpc/cpu/mpc8xx/Kconfig
@@ -28,9 +28,6 @@ config TARGET_LWMON
config TARGET_NETVIA
bool "Support NETVIA"
-config TARGET_R360MPI
- bool "Support R360MPI"
-
config TARGET_TQM823L
bool "Support TQM823L"
@@ -75,7 +72,6 @@ source "board/ip860/Kconfig"
source "board/ivm/Kconfig"
source "board/lwmon/Kconfig"
source "board/netvia/Kconfig"
-source "board/r360mpi/Kconfig"
source "board/tqc/tqm8xx/Kconfig"
endmenu
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index f772787..9350fdd 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -129,7 +129,6 @@ void cpu_init_f (volatile immap_t * immr)
defined(CONFIG_IVML24) || \
defined(CONFIG_IVMS8) || \
defined(CONFIG_LWMON) || \
- defined(CONFIG_R360MPI) || \
defined(CONFIG_RMU)
memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM;
diff --git a/board/r360mpi/Kconfig b/board/r360mpi/Kconfig
deleted file mode 100644
index fe8484f..0000000
--- a/board/r360mpi/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_R360MPI
-
-config SYS_BOARD
- default "r360mpi"
-
-config SYS_CONFIG_NAME
- default "R360MPI"
-
-endif
diff --git a/board/r360mpi/MAINTAINERS b/board/r360mpi/MAINTAINERS
deleted file mode 100644
index a67ab0c..0000000
--- a/board/r360mpi/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-R360MPI BOARD
-M: Wolfgang Denk <wd at denx.de>
-S: Maintained
-F: board/r360mpi/
-F: include/configs/R360MPI.h
-F: configs/R360MPI_defconfig
diff --git a/board/r360mpi/Makefile b/board/r360mpi/Makefile
deleted file mode 100644
index f8f7fe7..0000000
--- a/board/r360mpi/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = r360mpi.o flash.o pcmcia.o
diff --git a/board/r360mpi/flash.c b/board/r360mpi/flash.c
deleted file mode 100644
index 996a22e..0000000
--- a/board/r360mpi/flash.c
+++ /dev/null
@@ -1,468 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* #define DEBUG */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Protection Flags:
- */
-#define FLAG_PROTECT_SET 0x01
-#define FLAG_PROTECT_CLEAR 0x02
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#else
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0;
- int i;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
- size_b0 = flash_get_size ((FPW *) FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size_b0, size_b0 << 20);
- }
-
- /* Remap FLASH according to real size */
- memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size_b0 & 0xFFFF8000);
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size_b0 = flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- (void) flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[0]);
-#endif
-
- flash_info[0].size = size_b0;
-
- return (size_b0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00020000);
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F320J3A:
- printf ("28F320J3A\n");
- break;
- case FLASH_28F640J3A:
- printf ("28F640J3A\n");
- break;
- case FLASH_28F128J3A:
- printf ("28F128J3A\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
- FPW value;
-
- /* Make sure Block Lock Bits get cleared */
- addr[0] = (FPW) 0x00FF00FF;
- addr[0] = (FPW) 0x00600060;
- addr[0] = (FPW) 0x00D000D0;
- addr[0] = (FPW) 0x00FF00FF;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = (FPW) 0x00AA00AA;
- addr[0x2AAA] = (FPW) 0x00550055;
- addr[0x5555] = (FPW) 0x00900090;
-
- value = addr[0];
-
- debug("Manuf. ID @ 0x%08lx: 0x%08x\n", (ulong)addr, value);
-
- switch (value) {
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- value = addr[1]; /* device ID */
-
- debug("Device ID @ 0x%08lx: 0x%08x\n", (ulong)(&addr[1]), value);
-
- switch (value) {
- case (FPW) INTEL_ID_28F320J3A:
- info->flash_id += FLASH_28F320J3A;
- info->sector_count = 32;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case (FPW) INTEL_ID_28F640J3A:
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case (FPW) INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type, start, now, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- *addr = (FPW) 0x00500050; /* clear status register */
- *addr = (FPW) 0x00200020; /* erase setup */
- *addr = (FPW) 0x00D000D0; /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = (FPW) 0x00B000B0; /* suspend erase */
- *addr = (FPW) 0x00FF00FF; /* reset to read mode */
- rcode = 1;
- break;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- *addr = (FPW) 0x00FF00FF; /* reset to read mode */
- }
- }
- printf (" done\n");
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
-
- int i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#else
- wp = (addr & ~3);
- port_width = 4;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- start = get_timer (0);
-
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
-
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
diff --git a/board/r360mpi/pcmcia.c b/board/r360mpi/pcmcia.c
deleted file mode 100644
index a939b31..0000000
--- a/board/r360mpi/pcmcia.c
+++ /dev/null
@@ -1,232 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#ifdef CONFIG_PCMCIA
-
-#define PCMCIA_BOARD_MSG "R360MPI"
-
-int pcmcia_hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CONFIG_SYS_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A, B & C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-#if 0
- immap->im_ioport.iop_pbpar &= ~(0xC000);
- immap->im_ioport.iop_pbdir &= ~(0xC000);
-#endif
- /* remove all power */
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- immap->im_ioport.iop_pcdat &= ~(0x4000);
- puts (" 5.0V card found: ");
- } else {
- immap->im_ioport.iop_padat &= ~(0x0002);
- puts (" 3.3V card found: ");
- }
- immap->im_ioport.iop_pcdir |= 0x0400;
- immap->im_ioport.iop_padir |= 0x0200;
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
- volatile immap_t *immap;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CONFIG_SYS_IMMR;
-
- /* remove all power */
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif
-
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CONFIG_SYS_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A & C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x0200; break;
- case 50: reg |= 0x0400; break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- if (reg & 0x0200)
- immap->im_ioport.iop_pcdat &= !reg;
- if (reg & 0x0400)
- immap->im_ioport.iop_padat &= !reg;
- immap->im_ioport.iop_pcdir |= 0x0200;
- immap->im_ioport.iop_padir |= 0x0400;
- if (reg) {
- debug ("PCMCIA powered at %sV\n",
- (reg&0x0400) ? "5.0" : "3.3");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* CCONFIG_PCMCIA */
diff --git a/board/r360mpi/r360mpi.c b/board/r360mpi/r360mpi.c
deleted file mode 100644
index d06aea7..0000000
--- a/board/r360mpi/r360mpi.c
+++ /dev/null
@@ -1,403 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <mpc8xx.h>
-#include <i2c.h>
-
-#include <commproc.h>
-#include <command.h>
-#include <malloc.h>
-
-#include <linux/types.h>
-#include <linux/string.h> /* for strdup */
-
-
-/*
- * Memory Controller Using
- *
- * CS0 - Flash memory (0x40000000)
- * CS1 - FLASH memory (0x????????)
- * CS2 - SDRAM (0x00000000)
- * CS3 -
- * CS4 -
- * CS5 -
- * CS6 - PCMCIA device
- * CS7 - PCMCIA device
- */
-
-/* ------------------------------------------------------------------------- */
-
-#define _not_used_ 0xffffffff
-
-const uint sdram_table[]=
-{
- /* single read. (offset 0 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
- 0x1ff77c47,
-
- /* MRS initialization (offset 5) */
-
- 0x1ff77c34, 0xefeabc34, 0x1fb57c35,
-
- /* burst read. (offset 8 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
- 0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* single write. (offset 18 in upm RAM) */
- 0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* burst write. (offset 20 in upm RAM) */
- 0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
- 0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* refresh. (offset 30 in upm RAM) */
- 0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
- 0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* exception. (offset 3c in upm RAM) */
- 0x7ffffc07, _not_used_, _not_used_, _not_used_ };
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
- puts ("Board: R360 MPI Board\n");
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size8, size9;
- long int size_b0 = 0;
- unsigned long reg;
-
- upmconfig (UPMA, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller bank 2 to the SDRAM bank at
- * preliminary address - these have to be modified after the
- * SDRAM size has been determined.
- */
- memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
- memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
-
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
- udelay (200);
- memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
- udelay (200);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 2 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, (long *) SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, (long *) SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size_b0 = size9;
-/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
- } else { /* back to 8 columns */
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
-/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
- }
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ((size_b0 < 0x02000000)) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /*
- * Final mapping
- */
-
- memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
-
- udelay (10000);
-
-#ifdef CONFIG_CAN_DRIVER
- /* Initialize OR3 / BR3 */
- memctl->memc_or3 = CONFIG_SYS_OR3_CAN; /* switch GPLB_5 to GPLA_5 */
- memctl->memc_br3 = CONFIG_SYS_BR3_CAN;
-
- /* Initialize MBMR */
- memctl->memc_mbmr = MBMR_GPL_B4DIS; /* GPL_B4 works as UPWAITB */
-
- /* Initialize UPMB for CAN: single read */
- memctl->memc_mdr = 0xFFFFC004;
- memctl->memc_mcr = 0x0100 | UPMB;
-
- memctl->memc_mdr = 0x0FFFD004;
- memctl->memc_mcr = 0x0101 | UPMB;
-
- memctl->memc_mdr = 0x0FFFC000;
- memctl->memc_mcr = 0x0102 | UPMB;
-
- memctl->memc_mdr = 0x3FFFC004;
- memctl->memc_mcr = 0x0103 | UPMB;
-
- memctl->memc_mdr = 0xFFFFDC05;
- memctl->memc_mcr = 0x0104 | UPMB;
-
- /* Initialize UPMB for CAN: single write */
- memctl->memc_mdr = 0xFFFCC004;
- memctl->memc_mcr = 0x0118 | UPMB;
-
- memctl->memc_mdr = 0xCFFCD004;
- memctl->memc_mcr = 0x0119 | UPMB;
-
- memctl->memc_mdr = 0x0FFCC000;
- memctl->memc_mcr = 0x011A | UPMB;
-
- memctl->memc_mdr = 0x7FFCC004;
- memctl->memc_mcr = 0x011B | UPMB;
-
- memctl->memc_mdr = 0xFFFDCC05;
- memctl->memc_mcr = 0x011C | UPMB;
-#endif
-
- return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value,
- long int *base, long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
-
-/* ------------------------------------------------------------------------- */
-
-void r360_i2c_lcd_write (uchar data0, uchar data1)
-{
- if (i2c_write (CONFIG_SYS_I2C_LCD_ADDR, data0, 1, &data1, 1)) {
- printf("Can't write lcd data 0x%02X 0x%02X.\n", data0, data1);
- }
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*-----------------------------------------------------------------------
- * Keyboard Controller
- */
-
-/* Number of bytes returned from Keyboard Controller */
-#define KEYBD_KEY_MAX 16 /* maximum key number */
-#define KEYBD_DATALEN ((KEYBD_KEY_MAX + 7) / 8) /* normal key scan data */
-
-static uchar *key_match (uchar *);
-
-int misc_init_r (void)
-{
- char kbd_data[KEYBD_DATALEN];
- char keybd_env[2 * KEYBD_DATALEN + 1];
- char *str;
- int i;
-
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- i2c_read (CONFIG_SYS_I2C_KEY_ADDR, 0, 0, (uchar *)kbd_data, KEYBD_DATALEN);
-
- for (i = 0; i < KEYBD_DATALEN; ++i) {
- sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
- }
- setenv ("keybd", keybd_env);
-
- str = strdup ((char *)key_match ((uchar *)keybd_env)); /* decode keys */
-
-#ifdef CONFIG_PREBOOT /* automatically configure "preboot" command on key match */
- setenv ("preboot", str); /* set or delete definition */
-#endif /* CONFIG_PREBOOT */
- if (str != NULL) {
- free (str);
- }
-
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- * Check if pressed key(s) match magic sequence,
- * and return the command string associated with that key(s).
- *
- * If no key press was decoded, NULL is returned.
- *
- * Note: the first character of the argument will be overwritten with
- * the "magic charcter code" of the decoded key(s), or '\0'.
- *
- *
- * Note: the string points to static environment data and must be
- * saved before you call any function that modifies the environment.
- */
-#ifdef CONFIG_PREBOOT
-
-static uchar kbd_magic_prefix[] = "key_magic";
-static uchar kbd_command_prefix[] = "key_cmd";
-
-static uchar *key_match (uchar * kbd_str)
-{
- uchar magic[sizeof (kbd_magic_prefix) + 1];
- uchar cmd_name[sizeof (kbd_command_prefix) + 1];
- uchar *str, *suffix;
- uchar *kbd_magic_keys;
- char *cmd;
-
- /*
- * The following string defines the characters that can pe appended
- * to "key_magic" to form the names of environment variables that
- * hold "magic" key codes, i. e. such key codes that can cause
- * pre-boot actions. If the string is empty (""), then only
- * "key_magic" is checked (old behaviour); the string "125" causes
- * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
- */
- if ((kbd_magic_keys = (uchar *)getenv ("magic_keys")) != NULL) {
- /* loop over all magic keys;
- * use '\0' suffix in case of empty string
- */
- for (suffix = kbd_magic_keys;
- *suffix || suffix == kbd_magic_keys;
- ++suffix) {
- sprintf ((char *)magic, "%s%c", kbd_magic_prefix, *suffix);
-
-#if 0
- printf ("### Check magic \"%s\"\n", magic);
-#endif
-
- if ((str = (uchar *)getenv ((char *)magic)) != 0) {
-
-#if 0
- printf ("### Compare \"%s\" \"%s\"\n",
- kbd_str, str);
-#endif
- if (strcmp ((char *)kbd_str, (char *)str) == 0) {
- sprintf ((char *)cmd_name, "%s%c",
- kbd_command_prefix,
- *suffix);
-
- if ((cmd = getenv ((char *)cmd_name)) != 0) {
-#if 0
- printf ("### Set PREBOOT to $(%s): \"%s\"\n",
- cmd_name, cmd);
-#endif
- return ((uchar *)cmd);
- }
- }
- }
- }
- }
-#if 0
- printf ("### Delete PREBOOT\n");
-#endif
- *kbd_str = '\0';
- return (NULL);
-}
-#endif /* CONFIG_PREBOOT */
-
-/* Read Keyboard status */
-int do_kbd (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
- uchar kbd_data[KEYBD_DATALEN];
- uchar keybd_env[2 * KEYBD_DATALEN + 1];
- int i;
-
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- /* Read keys */
- i2c_read (CONFIG_SYS_I2C_KEY_ADDR, 0, 0, kbd_data, KEYBD_DATALEN);
-
- puts ("Keys:");
- for (i = 0; i < KEYBD_DATALEN; ++i) {
- sprintf ((char *)(keybd_env + i + i), "%02X", kbd_data[i]);
- printf (" %02x", kbd_data[i]);
- }
- putc ('\n');
- setenv ("keybd", (char *)keybd_env);
- return 0;
-}
-
-U_BOOT_CMD(
- kbd, 1, 1, do_kbd,
- "read keyboard status",
- ""
-);
diff --git a/board/r360mpi/u-boot.lds b/board/r360mpi/u-boot.lds
deleted file mode 100644
index 5f69bc4..0000000
--- a/board/r360mpi/u-boot.lds
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
- . = ALIGN(128 * 1024);
- .ppcenv :
- {
- common/env_embedded.o (.ppcenv)
- }
-}
diff --git a/configs/R360MPI_defconfig b/configs/R360MPI_defconfig
deleted file mode 100644
index 290f694..0000000
--- a/configs/R360MPI_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_R360MPI=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 00a5447..1e475af 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+R360MPI powerpc mpc8xx - - Wolfgang Denk <wd at denx.de>
RRvision powerpc mpc8xx - - Wolfgang Denk <wd at denx.de>
SPD823TS powerpc mpc8xx - - Wolfgang Denk <wd at denx.de>
KUP4K powerpc mpc8xx - - Klaus Heydeck <heydeck at kieback-peter.de>
diff --git a/drivers/video/mpc8xx_lcd.c b/drivers/video/mpc8xx_lcd.c
index a5c1e19..336788f 100644
--- a/drivers/video/mpc8xx_lcd.c
+++ b/drivers/video/mpc8xx_lcd.c
@@ -423,31 +423,6 @@ void lcd_enable (void)
pic_write (0x60, c);
}
#endif /* CONFIG_LWMON */
-
-#if defined(CONFIG_R360MPI)
- {
- extern void r360_i2c_lcd_write (uchar data0, uchar data1);
- unsigned long bgi, ctr;
- char *p;
-
- if ((p = getenv("lcdbgi")) != NULL) {
- bgi = simple_strtoul (p, 0, 10) & 0xFFF;
- } else {
- bgi = 0xFFF;
- }
-
- if ((p = getenv("lcdctr")) != NULL) {
- ctr = simple_strtoul (p, 0, 10) & 0xFFF;
- } else {
- ctr=0x7FF;
- }
-
- r360_i2c_lcd_write(0x10, 0x01);
- r360_i2c_lcd_write(0x20, 0x01);
- r360_i2c_lcd_write(0x30 | ((bgi>>8) & 0xF), bgi & 0xFF);
- r360_i2c_lcd_write(0x40 | ((ctr>>8) & 0xF), ctr & 0xFF);
- }
-#endif /* CONFIG_R360MPI */
}
/************************************************************************/
diff --git a/include/commproc.h b/include/commproc.h
index 7d62861..38e4e7d 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -630,7 +630,6 @@ typedef struct scc_enet {
/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_R360MPI) || \
defined(CONFIG_TQM823L) || \
defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D)
@@ -650,9 +649,6 @@ typedef struct scc_enet {
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#if defined(CONFIG_R360MPI)
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#endif /* CONFIG_R360MPI */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
diff --git a/include/configs/R360MPI.h b/include/configs/R360MPI.h
deleted file mode 100644
index 009d1cf..0000000
--- a/include/configs/R360MPI.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_R360MPI 1
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_LCD
-#define CONFIG_MPC8XX_LCD
-#undef CONFIG_EDT32F10
-#define CONFIG_SHARP_LQ057Q3DC02
-
-#define CONFIG_SPLASH_SCREEN
-
-#define MPC8XX_FACT 1 /* Multiply by 1 */
-#define MPC8XX_XIN 50000000 /* 50 MHz in */
-#define CONFIG_8xx_GCLK_FREQ 50000000 /* define if can't use get_gclk_freq */
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200 /* console baudrate in bps */
-#if 0
-#define CONFIG_BOOTDELAY 0 /* immediate boot */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-
-#undef CONFIG_SCC1_ENET
-#define CONFIG_SCC2_ENET
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#define CONFIG_MISC_INIT_R /* have misc_init_r() function */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_CAN_DRIVER /* CAN Driver support enabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */
-#undef CONFIG_SYS_I2C_SOFT /* To I2C with software support */
-#define CONFIG_SYS_I2C_SPEED 4700 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#if defined(CONFIG_SYS_I2C_SOFT)
-#define CONFIG_SYS_SYS_I2C_SOFT_SPEED 4700 /* I2C speed and slave address */
-#define CONFIG_SYS_SYS_I2C_SOFT_SLAVE 0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(50)
-#endif /* #define(CONFIG_SYS_I2C_SOFT) */
-
-#define CONFIG_SYS_I2C_LCD_ADDR 0x8 /* LCD Control */
-#define CONFIG_SYS_I2C_KEY_ADDR 0x9 /* Keyboard coprocessor */
-#define CONFIG_SYS_I2C_TEM_ADDR 0x49 /* Temperature Sensors */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* we need the null device */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 /* must set console from env */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition
- * use all the space starting at offset 3MB*/
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00300000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor0=r360-0"
-#define MTDPARTS_DEFAULT "mtdparts=r360-0:- at 3m(user)"
-*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#if defined(DEBUG)
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment sector */
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CONFIG_SYS_PLPRCR \
- ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else /* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif /* CONFIG_80MHz */
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_TBS | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#if 1
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_SCY_7_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-
-/*
- * BR2 and OR2 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-#define CONFIG_SYS_PRELIM_OR2_AM 0xF8000000 /* OR addr mask */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM (OR_ACS_DIV1 | OR_CSNT_SAM | \
- OR_SCY_0_CLK | OR_G5LS)
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR2_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/*
- * BR3 and OR3 (CAN Controller)
- */
-#ifdef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN base address */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA |OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V)
-#endif /* CONFIG_CAN_DRIVER */
-
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-#if defined(CONFIG_80MHz)
-#define CONFIG_SYS_MAMR_PTA 156
-#elif defined(CONFIG_66MHz)
-#define CONFIG_SYS_MAMR_PTA 129
-#else /* 50 MHz */
-#define CONFIG_SYS_MAMR_PTA 98
-#endif /*CONFIG_??MHz */
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#endif /* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 371c9a4..7e495bc 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -27,8 +27,6 @@
# define CONFIG_PCMCIA_SLOT_A
#elif defined(CONFIG_LWMON) /* The LWMON use SLOT_B */
# define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_R360MPI) /* The R360MPI use SLOT_B */
-# define CONFIG_PCMCIA_SLOT_B
#elif defined(CONFIG_ATC) /* The ATC use SLOT_A */
# define CONFIG_PCMCIA_SLOT_A
#else
--
1.9.1
More information about the U-Boot
mailing list