[U-Boot] [PATCH 18/26] mpc8260: remove MPC8266ADS board support
Masahiro Yamada
yamada.m at jp.panasonic.com
Mon Dec 15 15:26:23 CET 2014
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
Cc: Rune Torgersen <runet at innovsys.com>
---
arch/powerpc/cpu/mpc8260/Kconfig | 4 -
arch/powerpc/cpu/mpc8260/pci.c | 57 +---
board/freescale/mpc8266ads/Kconfig | 12 -
board/freescale/mpc8266ads/MAINTAINERS | 6 -
board/freescale/mpc8266ads/Makefile | 8 -
board/freescale/mpc8266ads/flash.c | 493 ---------------------------
board/freescale/mpc8266ads/mpc8266ads.c | 582 --------------------------------
configs/MPC8266ADS_defconfig | 3 -
doc/README.scrapyard | 1 +
include/configs/MPC8266ADS.h | 563 ------------------------------
10 files changed, 3 insertions(+), 1726 deletions(-)
delete mode 100644 board/freescale/mpc8266ads/Kconfig
delete mode 100644 board/freescale/mpc8266ads/MAINTAINERS
delete mode 100644 board/freescale/mpc8266ads/Makefile
delete mode 100644 board/freescale/mpc8266ads/flash.c
delete mode 100644 board/freescale/mpc8266ads/mpc8266ads.c
delete mode 100644 configs/MPC8266ADS_defconfig
delete mode 100644 include/configs/MPC8266ADS.h
diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index 15742d9..d9dba83 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -34,9 +34,6 @@ config TARGET_PM826
config TARGET_PM828
bool "Support PM828"
-config TARGET_MPC8266ADS
- bool "Support MPC8266ADS"
-
config TARGET_KM82XX
bool "Support km82xx"
@@ -46,7 +43,6 @@ source "board/atc/Kconfig"
source "board/cpu86/Kconfig"
source "board/cpu87/Kconfig"
source "board/ep82xxm/Kconfig"
-source "board/freescale/mpc8266ads/Kconfig"
source "board/gw8260/Kconfig"
source "board/iphase4539/Kconfig"
source "board/keymile/km82xx/Kconfig"
diff --git a/arch/powerpc/cpu/mpc8260/pci.c b/arch/powerpc/cpu/mpc8260/pci.c
index f7bb05d..079b6e6 100644
--- a/arch/powerpc/cpu/mpc8260/pci.c
+++ b/arch/powerpc/cpu/mpc8260/pci.c
@@ -22,7 +22,7 @@
#include <fdt_support.h>
#endif
-#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272 || defined CONFIG_PM826
+#if defined CONFIG_PM826
DECLARE_GLOBAL_DATA_PTR;
#endif
@@ -236,34 +236,6 @@ void pci_mpc8250_init (struct pci_controller *hose)
CONFIG_SYS_IMMR + PCI_CFG_DATA_REG);
/*
- * Setting required to enable local bus for PCI (SIUMCR [LBPC]).
- */
-#ifdef CONFIG_MPC8266ADS
- immap->im_siu_conf.sc_siumcr =
- (immap->im_siu_conf.sc_siumcr & ~SIUMCR_LBPC11)
- | SIUMCR_LBPC01;
-#elif defined CONFIG_MPC8272
- immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr &
- ~SIUMCR_BBD &
- ~SIUMCR_ESE &
- ~SIUMCR_PBSE &
- ~SIUMCR_CDIS &
- ~SIUMCR_DPPC11 &
- ~SIUMCR_L2CPC11 &
- ~SIUMCR_LBPC11 &
- ~SIUMCR_APPC11 &
- ~SIUMCR_CS10PC11 &
- ~SIUMCR_BCTLC11 &
- ~SIUMCR_MMR11)
- | SIUMCR_DPPC11
- | SIUMCR_L2CPC01
- | SIUMCR_LBPC00
- | SIUMCR_APPC10
- | SIUMCR_CS10PC00
- | SIUMCR_BCTLC00
- | SIUMCR_MMR11;
-#else
- /*
* Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]),
* and local bus for PCI (SIUMCR [LBPC]).
*/
@@ -274,7 +246,6 @@ void pci_mpc8250_init (struct pci_controller *hose)
SIUMCR_LBPC01 |
SIUMCR_CS10PC01 |
SIUMCR_APPC10;
-#endif
/* Make PCI lowest priority */
/* Each 4 bits is a device bus request and the MS 4bits
@@ -304,24 +275,11 @@ void pci_mpc8250_init (struct pci_controller *hose)
immap->im_memctl.memc_pcimsk0 = PCIMSK0_MASK;
immap->im_memctl.memc_pcibr0 = PCI_MSTR0_LOCAL | PCIBR_ENABLE;
-#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
- immap->im_memctl.memc_pcimsk1 = PCIMSK1_MASK;
- immap->im_memctl.memc_pcibr1 = PCI_MSTR1_LOCAL | PCIBR_ENABLE;
-#endif
-
/* Release PCI RST (by default the PCI RST signal is held low) */
immap->im_pci.pci_gcr = cpu_to_le32 (PCIGCR_PCI_BUS_EN);
/* give it some time */
{
-#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
- /* Give the PCI cards more time to initialize before query
- This might be good for other boards also
- */
- int i;
-
- for (i = 0; i < 1000; ++i)
-#endif
udelay (1000);
}
@@ -358,11 +316,7 @@ void pci_mpc8250_init (struct pci_controller *hose)
immap->im_pci.pci_picmr0 = cpu_to_le32 (PICMR0_MASK_ATTRIB); /* Size & attribute */
/* See above for description - puts PCI request as highest priority */
-#ifdef CONFIG_MPC8272
- immap->im_siu_conf.sc_ppc_alrh = 0x01236745;
-#else
immap->im_siu_conf.sc_ppc_alrh = 0x03124567;
-#endif
/* Park the bus on the PCI */
immap->im_siu_conf.sc_ppc_acr = PPC_ACR_BUS_PARK_PCI;
@@ -388,7 +342,7 @@ void pci_mpc8250_init (struct pci_controller *hose)
hose->last_busno = 0xff;
/* System memory space */
-#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272 || defined CONFIG_PM826
+#if defined CONFIG_PM826
pci_set_region (hose->regions + 0,
PCI_SLV_MEM_BUS,
PCI_SLV_MEM_LOCAL,
@@ -401,17 +355,10 @@ void pci_mpc8250_init (struct pci_controller *hose)
#endif
/* PCI memory space */
-#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
- pci_set_region (hose->regions + 1,
- PCI_MSTR_MEMIO_BUS,
- PCI_MSTR_MEMIO_LOCAL,
- PCI_MSTR_MEMIO_SIZE, PCI_REGION_MEM);
-#else
pci_set_region (hose->regions + 1,
PCI_MSTR_MEM_BUS,
PCI_MSTR_MEM_LOCAL,
PCI_MSTR_MEM_SIZE, PCI_REGION_MEM);
-#endif
/* PCI I/O space */
pci_set_region (hose->regions + 2,
diff --git a/board/freescale/mpc8266ads/Kconfig b/board/freescale/mpc8266ads/Kconfig
deleted file mode 100644
index 78963b9..0000000
--- a/board/freescale/mpc8266ads/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8266ADS
-
-config SYS_BOARD
- default "mpc8266ads"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8266ADS"
-
-endif
diff --git a/board/freescale/mpc8266ads/MAINTAINERS b/board/freescale/mpc8266ads/MAINTAINERS
deleted file mode 100644
index bdea02d..0000000
--- a/board/freescale/mpc8266ads/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MPC8266ADS BOARD
-M: Rune Torgersen <runet at innovsys.com>
-S: Maintained
-F: board/freescale/mpc8266ads/
-F: include/configs/MPC8266ADS.h
-F: configs/MPC8266ADS_defconfig
diff --git a/board/freescale/mpc8266ads/Makefile b/board/freescale/mpc8266ads/Makefile
deleted file mode 100644
index ee63dc0..0000000
--- a/board/freescale/mpc8266ads/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := mpc8266ads.o flash.o
diff --git a/board/freescale/mpc8266ads/flash.c b/board/freescale/mpc8266ads/flash.c
deleted file mode 100644
index ef28194..0000000
--- a/board/freescale/mpc8266ads/flash.c
+++ /dev/null
@@ -1,493 +0,0 @@
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth at lineo.com
- * Add support the Sharp chips on the mpc8260ads.
- * I started with board/ip860/flash.c and made changes I found in
- * the MTD project by David Schleef.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static int clear_block_lock_bit(vu_long * addr);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-#ifndef CONFIG_MPC8266ADS
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- volatile ip860_bcsr_t *bcsr = (ip860_bcsr_t *)BCSR_BASE;
-#endif
- unsigned long size;
- int i;
-
- /* Init: enable write,
- * or we cannot even write flash commands
- */
-#ifndef CONFIG_MPC8266ADS
- bcsr->bd_ctrl |= BD_CTRL_FLWE;
-#endif
-
-
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- /* set the default sector offset */
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- size = flash_get_size((vu_long *)FLASH_BASE, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size, size<<20);
- }
-
-#ifndef CONFIG_MPC8266ADS
- /* Remap FLASH according to real size */
- memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH | (-size & 0xFFFF8000);
- memctl->memc_br1 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) |
- (memctl->memc_br1 & ~(BR_BA_MSK));
-#endif
- /* Re-do sizing to get full correct info */
- size = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_info[0].size = size;
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[0]);
-#endif
- return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL: printf ("Intel "); break;
- case FLASH_MAN_SHARP: printf ("Sharp "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F016SV: printf ("28F016SV (16 Mbit, 32 x 64k)\n");
- break;
- case FLASH_28F160S3: printf ("28F160S3 (16 Mbit, 32 x 512K)\n");
- break;
- case FLASH_28F320S3: printf ("28F320S3 (32 Mbit, 64 x 512K)\n");
- break;
- case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
- ulong value;
- ulong base = (ulong)addr;
- ulong sector_offset;
-
- /* Write "Intelligent Identifier" command: read Manufacturer ID */
- *addr = 0x90909090;
-
- value = addr[0] & 0x00FF00FF;
- switch (value) {
- case MT_MANUFACT: /* SHARP, MT or => Intel */
- case INTEL_ALT_MANU:
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- printf("unknown manufacturer: %x\n", (unsigned int)value);
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-
- value = addr[1]; /* device ID */
-
- switch (value) {
- case (INTEL_ID_28F016S):
- info->flash_id += FLASH_28F016SV;
- info->sector_count = 32;
- info->size = 0x00400000;
- sector_offset = 0x20000;
- break; /* => 2x2 MB */
-
- case (INTEL_ID_28F160S3):
- info->flash_id += FLASH_28F160S3;
- info->sector_count = 32;
- info->size = 0x00400000;
- sector_offset = 0x20000;
- break; /* => 2x2 MB */
-
- case (INTEL_ID_28F320S3):
- info->flash_id += FLASH_28F320S3;
- info->sector_count = 64;
- info->size = 0x00800000;
- sector_offset = 0x20000;
- break; /* => 2x4 MB */
-
- case SHARP_ID_28F016SCL:
- case SHARP_ID_28F016SCZ:
- info->flash_id = FLASH_MAN_SHARP | FLASH_LH28F016SCT;
- info->sector_count = 32;
- info->size = 0x00800000;
- sector_offset = 0x40000;
- break; /* => 4x2 MB */
-
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
-
- }
-
- /* set up sector start address table */
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += sector_offset;
- /* don't know how to check sector protection */
- info->protect[i] = 0;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (vu_long *)info->start[0];
-
- *addr = 0xFFFFFF; /* reset bank to read array mode */
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ( ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
- && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- /* Make Sure Block Lock Bit is not set. */
- if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
- return 1;
- }
-
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_long *addr = (vu_long *)(info->start[sect]);
-
- last = start = get_timer (0);
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* Reset Array */
- *addr = 0xffffffff;
- /* Clear Status Register */
- *addr = 0x50505050;
- /* Single Block Erase Command */
- *addr = 0x20202020;
- /* Confirm */
- *addr = 0xD0D0D0D0;
-
- if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
- /* Resume Command, as per errata update */
- *addr = 0xD0D0D0D0;
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
- while ((*addr & 0x80808080) != 0x80808080) {
- if(*addr & 0x20202020){
- printf("Error in Block Erase - Lock Bit may be set!\n");
- printf("Status Register = 0x%X\n", (uint)*addr);
- *addr = 0xFFFFFFFF; /* reset bank */
- return 1;
- }
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = 0xFFFFFFFF; /* reset bank */
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- /* reset to read mode */
- *addr = 0xFFFFFFFF;
- }
- }
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long *)dest;
- ulong start, csr;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* Write Command */
- *addr = 0x10101010;
-
- /* Write Data */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- flag = 0;
- while (((csr = *addr) & 0x80808080) != 0x80808080) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- flag = 1;
- break;
- }
- }
- if (csr & 0x40404040) {
- printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
- flag = 1;
- }
-
- /* Clear Status Registers Command */
- *addr = 0x50505050;
- /* Reset to read array mode */
- *addr = 0xFFFFFFFF;
-
- return (flag);
-}
-
-/*-----------------------------------------------------------------------
- * Clear Block Lock Bit, returns:
- * 0 - OK
- * 1 - Timeout
- */
-
-static int clear_block_lock_bit(vu_long * addr)
-{
- ulong start, now;
-
- /* Reset Array */
- *addr = 0xffffffff;
- /* Clear Status Register */
- *addr = 0x50505050;
-
- *addr = 0x60606060;
- *addr = 0xd0d0d0d0;
-
- start = get_timer (0);
- while(*addr != 0x80808080){
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout on clearing Block Lock Bit\n");
- *addr = 0xFFFFFFFF; /* reset bank */
- return 1;
- }
- }
- return 0;
-}
diff --git a/board/freescale/mpc8266ads/mpc8266ads.c b/board/freescale/mpc8266ads/mpc8266ads.c
deleted file mode 100644
index 1eeec3f..0000000
--- a/board/freescale/mpc8266ads/mpc8266ads.c
+++ /dev/null
@@ -1,582 +0,0 @@
-/*
- * (C) Copyright 2001-2011
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * Modified during 2001 by
- * Advanced Communications Technologies (Australia) Pty. Ltd.
- * Howard Walker, Tuong Vu-Dinh
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth at lineo.com
- * Added support for the 16M dram simm on the 8260ads boards
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <i2c.h>
-#include <mpc8260.h>
-#include <pci.h>
-
-/*
- * PBI Page Based Interleaving
- * PSDMR_PBI page based interleaving
- * 0 bank based interleaving
- * External Address Multiplexing (EAMUX) adds a clock to address cycles
- * (this can help with marginal board layouts)
- * PSDMR_EAMUX adds a clock
- * 0 no extra clock
- * Buffer Command (BUFCMD) adds a clock to command cycles.
- * PSDMR_BUFCMD adds a clock
- * 0 no extra clock
- */
-#define CONFIG_PBI 0
-#define PESSIMISTIC_SDRAM 0
-#define EAMUX 0 /* EST requires EAMUX */
-#define BUFCMD 0
-
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
- /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
- /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
- /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
- /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
- /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
- /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
- /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
- /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
- /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
- /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
- /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
- /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
- /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
- /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
- /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
- /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
- /* PA6 */ { 1, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
- /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
- /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
- /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
- /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
- /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
- /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
- /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
- /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
- /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
- /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
- /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
- /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
- /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
- /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
- /* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
- /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
- /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* LXT970 FETHMDC */
- /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* LXT970 FETHMDIO */
- /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
- /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
- /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
- /* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
- /* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
- /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- }
-};
-
-typedef struct bscr_ {
- unsigned long bcsr0;
- unsigned long bcsr1;
- unsigned long bcsr2;
- unsigned long bcsr3;
- unsigned long bcsr4;
- unsigned long bcsr5;
- unsigned long bcsr6;
- unsigned long bcsr7;
-} bcsr_t;
-
-typedef struct pci_ic_s {
- unsigned long pci_int_stat;
- unsigned long pci_int_mask;
-} pci_ic_t;
-
-void reset_phy(void)
-{
- volatile bcsr_t *bcsr = (bcsr_t *)CONFIG_SYS_BCSR;
-
- /* reset the FEC port */
- bcsr->bcsr1 &= ~FETH_RST;
- bcsr->bcsr1 |= FETH_RST;
-}
-
-
-int board_early_init_f(void)
-{
- volatile bcsr_t *bcsr = (bcsr_t *)CONFIG_SYS_BCSR;
- volatile pci_ic_t *pci_ic = (pci_ic_t *)CONFIG_SYS_PCI_INT;
-
- bcsr->bcsr1 = ~FETHIEN & ~RS232EN_1 & ~RS232EN_2;
-
- /* mask all PCI interrupts */
- pci_ic->pci_int_mask |= 0xfff00000;
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: Motorola MPC8266ADS\n");
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- /* Autoinit part stolen from board/sacsng/sacsng.c */
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- volatile uchar c = 0xff;
- volatile uchar *ramaddr = (uchar *) (CONFIG_SYS_SDRAM_BASE + 0x8);
- uint psdmr = CONFIG_SYS_PSDMR;
- int i;
-
- uint psrt = 0x21; /* for no SPD */
- uint chipselects = 1; /* for no SPD */
- uint sdram_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; /* for no SPD */
- uint or = CONFIG_SYS_OR2_PRELIM; /* for no SPD */
- uint data_width;
- uint rows;
- uint banks;
- uint cols;
- uint caslatency;
- uint width;
- uint rowst;
- uint sdam;
- uint bsma;
- uint sda10;
- u_char data;
- u_char cksum;
- int j;
-
- /*
- * Keep the compiler from complaining about
- * potentially uninitialized vars
- */
- data_width = rows = banks = cols = caslatency = 0;
-
- /*
- * Read the SDRAM SPD EEPROM via I2C.
- */
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
- i2c_read(SDRAM_SPD_ADDR, 0, 1, &data, 1);
- cksum = data;
- for (j = 1; j < 64; j++) { /* read only the checksummed bytes */
- /* note: the I2C address autoincrements when alen == 0 */
- i2c_read(SDRAM_SPD_ADDR, 0, 0, &data, 1);
- /*printf("addr %d = 0x%02x\n", j, data); */
- if (j == 5)
- chipselects = data & 0x0F;
- else if (j == 6)
- data_width = data;
- else if (j == 7)
- data_width |= data << 8;
- else if (j == 3)
- rows = data & 0x0F;
- else if (j == 4)
- cols = data & 0x0F;
- else if (j == 12) {
- /*
- * Refresh rate: this assumes the prescaler is set to
- * approximately 0.39uSec per tick and the target
- * refresh period is about 85% of maximum.
- */
- switch (data & 0x7F) {
- default:
- case 0:
- psrt = 0x21; /* 15.625uS */
- break;
- case 1:
- psrt = 0x07; /* 3.9uS */
- break;
- case 2:
- psrt = 0x0F; /* 7.8uS */
- break;
- case 3:
- psrt = 0x43; /* 31.3uS */
- break;
- case 4:
- psrt = 0x87; /* 62.5uS */
- break;
- case 5:
- psrt = 0xFF; /* 125uS */
- break;
- }
- } else if (j == 17)
- banks = data;
- else if (j == 18) {
- caslatency = 3; /* default CL */
-#if (PESSIMISTIC_SDRAM)
- if ((data & 0x04) != 0)
- caslatency = 3;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x01) != 0)
- caslatency = 1;
-#else
- if ((data & 0x01) != 0)
- caslatency = 1;
- else if ((data & 0x02) != 0)
- caslatency = 2;
- else if ((data & 0x04) != 0)
- caslatency = 3;
-#endif
- else {
- printf("WARNING: Unknown CAS latency 0x%02X, using 3\n",
- data);
- }
- } else if (j == 63) {
- if (data != cksum) {
- printf("WARNING: Configuration data checksum failure:"
- " is 0x%02x, calculated 0x%02x\n",
- data, cksum);
- }
- }
- cksum += data;
- }
-
- /* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
- if (caslatency < 2) {
- printf("CL was %d, forcing to 2\n", caslatency);
- caslatency = 2;
- }
- if (rows > 14) {
- printf("This doesn't look good, rows = %d, should be <= 14\n",
- rows);
- rows = 14;
- }
- if (cols > 11) {
- printf("This doesn't look good, columns = %d, should be <= 11\n",
- cols);
- cols = 11;
- }
-
- if ((data_width != 64) && (data_width != 72)) {
- printf("WARNING: SDRAM width unsupported, is %d, expected 64 or 72.\n",
- data_width);
- }
- width = 3; /* 2^3 = 8 bytes = 64 bits wide */
- /*
- * Convert banks into log2(banks)
- */
- if (banks == 2)
- banks = 1;
- else if (banks == 4)
- banks = 2;
- else if (banks == 8)
- banks = 3;
-
-
- sdram_size = 1 << (rows + cols + banks + width);
- /* hack for high density memory (512MB per CS) */
- /* !!!!! Will ONLY work with Page Based Interleave !!!!!
- ( PSDMR[PBI] = 1 )
- */
- /*
- * memory actually has 11 column addresses, but the memory
- * controller doesn't really care.
- *
- * the calculations that follow will however move the rows so
- * that they are muxed one bit off if you use 11 bit columns.
- *
- * The solution is to tell the memory controller the correct
- * size of the memory but change the number of columns to 10
- * afterwards.
- *
- * The 11th column addre will still be mucxed correctly onto
- * the bus.
- *
- * Also be aware that the MPC8266ADS board Rev B has not
- * connected Row address 13 to anything.
- *
- * The fix is to connect ADD16 (from U37-47) to SADDR12 (U28-126)
- */
- if (cols > 10)
- cols = 10;
-
-#if (CONFIG_PBI == 0) /* bank-based interleaving */
- rowst = ((32 - 6) - (rows + cols + width)) * 2;
-#else
- rowst = 32 - (rows + banks + cols + width);
-#endif
-
- or = ~(sdram_size - 1) | /* SDAM address mask */
- ((banks - 1) << 13) | /* banks per device */
- (rowst << 9) | /* rowst */
- ((rows - 9) << 6); /* numr */
-
-
- /*printf("memctl->memc_or2 = 0x%08x\n", or); */
-
- /*
- * SDAM specifies the number of columns that are multiplexed
- * (reference AN2165/D), defined to be (columns - 6) for page
- * interleave, (columns - 8) for bank interleave.
- *
- * BSMA is 14 - max(rows, cols). The bank select lines come
- * into play above the highest "address" line going into the
- * the SDRAM.
- */
-#if (CONFIG_PBI == 0) /* bank-based interleaving */
- sdam = cols - 8;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam + 2;
-#else
- sdam = cols + banks - 8;
- bsma = ((31 - width) - 14) - ((rows > cols) ? rows : cols);
- sda10 = sdam;
-#endif
-#if (PESSIMISTIC_SDRAM)
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_16_CLK |
- PSDMR_PRETOACT_8W | PSDMR_ACTTORW_8W | PSDMR_WRC_4C |
- PSDMR_EAMUX | PSDMR_BUFCMD) | caslatency |
- ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#else
- psdmr = (CONFIG_PBI | PSDMR_RFEN | PSDMR_RFRC_7_CLK |
- PSDMR_PRETOACT_3W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_ACTTORW_2W | /* 1 for 7E parts (fast PC-133) */
- PSDMR_WRC_1C | /* 1 clock + 7nSec */
- EAMUX | BUFCMD) | caslatency |
- ((caslatency - 1) << 6) | /* LDOTOPRE is CL - 1 */
- (sdam << 24) | (bsma << 21) | (sda10 << 18);
-#endif
- /*printf("psdmr = 0x%08x\n", psdmr); */
-
- /*
- * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
- *
- * "At system reset, initialization software must set up the
- * programmable parameters in the memory controller banks registers
- * (ORx, BRx, P/LSDMR). After all memory parameters are configured,
- * system software should execute the following initialization sequence
- * for each SDRAM device.
- *
- * 1. Issue a PRECHARGE-ALL-BANKS command
- * 2. Issue eight CBR REFRESH commands
- * 3. Issue a MODE-SET command to initialize the mode register
- *
- * Quote from Micron MT48LC8M16A2 data sheet:
- *
- * "...the SDRAM requires a 100uS delay prior to issuing any
- * command other than a COMMAND INHIBIT or NOP. Starting at some
- * point during this 100uS period and continuing at least through
- * the end of this period, COMMAND INHIBIT or NOP commands should
- * be applied."
- *
- * "Once the 100uS delay has been satisfied with at least one COMMAND
- * INHIBIT or NOP command having been applied, a /PRECHARGE command/
- * should be applied. All banks must then be precharged, thereby
- * placing the device in the all banks idle state."
- *
- * "Once in the idle state, /two/ AUTO REFRESH cycles must be
- * performed. After the AUTO REFRESH cycles are complete, the
- * SDRAM is ready for mode register programming."
- *
- * (/emphasis/ mine, gvb)
- *
- * The way I interpret this, Micron start up sequence is:
- * 1. Issue a PRECHARGE-BANK command (initial precharge)
- * 2. Issue a PRECHARGE-ALL-BANKS command ("all banks ... precharged")
- * 3. Issue two (presumably, doing eight is OK) CBR REFRESH commands
- * 4. Issue a MODE-SET command to initialize the mode register
- *
- * --------
- *
- * The initial commands are executed by setting P/LSDMR[OP] and
- * accessing the SDRAM with a single-byte transaction."
- *
- * The appropriate BRx/ORx registers have already been set
- * when we get here. The SDRAM can be accessed at the address
- * CONFIG_SYS_SDRAM_BASE.
- */
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
- memctl->memc_psrt = psrt;
-
- memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
- memctl->memc_or2 = or;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
-
- /*
- * Do it a second time for the second set of chips if the DIMM has
- * two chip selects (double sided).
- */
- if (chipselects > 1) {
- ramaddr += sdram_size;
-
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM + sdram_size;
- memctl->memc_or3 = or;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
- *ramaddr = c;
-
- memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
- *ramaddr = c;
- }
-
- /* print info */
- printf("SDRAM configuration read from SPD\n");
- printf("\tSize per side = %dMB\n", sdram_size >> 20);
- printf("\tOrganization: %d sides, %d banks, %d Columns, %d Rows, Data width = %d bits\n",
- chipselects, 1 << (banks), cols, rows, data_width);
- printf("\tRefresh rate = %d, CAS latency = %d", psrt, caslatency);
-#if (CONFIG_PBI == 0) /* bank-based interleaving */
- printf(", Using Bank Based Interleave\n");
-#else
- printf(", Using Page Based Interleave\n");
-#endif
- printf("\tTotal size: ");
-
- /* this delay only needed for original 16MB DIMM...
- * Not needed for any other memory configuration */
- if ((sdram_size * chipselects) == (16 * 1024 * 1024))
- udelay(250000);
-
- return sdram_size * chipselects;
-}
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-extern void pci_mpc8250_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
- pci_mpc8250_init(&hose);
-}
-#endif
diff --git a/configs/MPC8266ADS_defconfig b/configs/MPC8266ADS_defconfig
deleted file mode 100644
index 485c842..0000000
--- a/configs/MPC8266ADS_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_MPC8266ADS=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7e4eaef..d358d62 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+MPC8266ADS powerpc mpc8260 - - Rune Torgersen <runet at innovsys.com>
VoVPN-GW powerpc mpc8260 - -
ep8260 powerpc mpc8260 - - Frank Panno <fpanno at delphintech.com>
ppmc8260 powerpc mpc8260 - - Brad Kemp <Brad.Kemp at seranoa.com>
diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
deleted file mode 100644
index 8d9c8fb..0000000
--- a/include/configs/MPC8266ADS.h
+++ /dev/null
@@ -1,563 +0,0 @@
-/*
- * (C) Copyright 2001
- * Stuart Hughes <stuarth at lineo.com>
- * This file is based on similar values for other boards found in other
- * U-Boot config files, and some that I found in the mpc8260ads manual.
- *
- * Note: my board is a PILOT rev.
- * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
-/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- !! !!
- !! This configuration requires JP3 to be in position 1-2 to work !!
- !! To make it work for the default, the CONFIG_SYS_TEXT_BASE define in !!
- !! board/mpc8266ads/config.mk must be changed from 0xfe000000 to !!
- !! 0xfff00000 !!
- !! The CONFIG_SYS_HRCW_MASTER define below must also be changed to match !!
- !! !!
- !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#define CONFIG_SYS_TEXT_BASE 0xfe000000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-/* allow serial and ethaddr to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-/*
- * Port pins used for bit-banged MII communictions (if applicable).
- */
-#define MDIO_PORT 2 /* Port C */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
-#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
-#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
-#define MIIDELAY udelay(1)
-
-#if (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
-
-/* other options */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* PCI */
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_BOOTDELAY 0
-#undef CONFIG_PCI_SCAN_SHOW
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS 0x50
-
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-/* Commands we want, that are not part of default set */
-#define CONFIG_CMD_ASKENV /* ask for env variable */
-#define CONFIG_CMD_CACHE /* icache, dcache */
-#define CONFIG_CMD_DHCP /* DHCP Support */
-#define CONFIG_CMD_DIAG /* Diagnostics */
-#define CONFIG_CMD_IMMAP /* IMMR dump support */
-#define CONFIG_CMD_IRQ /* irqinfo */
-#define CONFIG_CMD_MII /* MII support */
-#define CONFIG_CMD_PCI /* pciinfo */
-#define CONFIG_CMD_PING /* ping support */
-#define CONFIG_CMD_PORTIO /* Port I/O */
-#define CONFIG_CMD_REGINFO /* Register dump */
-#define CONFIG_CMD_SAVES /* save S record dump */
-#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */
-
-/* Commands from default set we don't need */
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-
-/* Define a command string that is automatically executed when no character
- * is read on the console interface withing "Boot Delay" after reset.
- */
-#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
-#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
-
-#ifdef CONFIG_BOOT_ROOT_INITRD
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/ram0 rw " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_INITRD */
-
-#ifdef CONFIG_BOOT_ROOT_NFS
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_NFS */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
- /* for versions < 2.4.5-pre5 */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define FLASH_BASE 0xFE000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_SIZE 8
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/* this is stuff came out of the Motorola docs */
-/* Only change this if you also change the Hardware configuration Word */
-#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
-
-/* Set IMMR to 0xF0000000 or above to boot Linux */
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_BCSR 0xF8000000
-#define CONFIG_SYS_PCI_INT 0xF8200000 /* PCI interrupt controller */
-
-/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
- */
-/*#define CONFIG_VERY_BIG_RAM 1*/
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)? This will normally auto-configure via the SPD.
-*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 16
-
-#define SDRAM_SPD_ADDR 0x50
-
-/*-----------------------------------------------------------------------
- * BR2,BR3 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR2,OR3 - Option Register
- * Ref: Section 10.3.2 on page 10-16
- *-----------------------------------------------------------------------
- */
-
-/* Bank 2,3 - SDRAM DIMM
- */
-
-/* The BR2 is configured as follows:
- *
- * - Base address of 0x00000000
- * - 64 bit port size (60x bus only)
- * - Data errors checking is disabled
- * - Read and write access
- * - SDRAM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-/* With a 64 MB DIMM, the OR2 is configured as follows:
- *
- * - 64 MB
- * - 4 internal banks per device
- * - Row start address bit is A8 with PSDMR[PBI] = 0
- * - 12 row address lines
- * - Back-to-back page mode
- * - Internal bank interleaving within save device enabled
- */
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-#define CONFIG_SYS_OR2_PRELIM (0xFF000C80)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*-----------------------------------------------------------------------
- * PSDMR - 60x Bus SDRAM Mode Register
- * Ref: Section 10.3.3 on page 10-21
- *-----------------------------------------------------------------------
- */
-
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-/* With a 64 MB DIMM, the PSDMR is configured as follows:
- *
- * - Bank Based Interleaving,
- * - Refresh Enable,
- * - Address Multiplexing where A5 is output on A14 pin
- * (A6 on A15, and so on),
- * - use address pins A14-A16 as bank select,
- * - A9 is output on SDA10 during an ACTIVATE command,
- * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
- * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
- * is 3 clocks,
- * - earliest timing for READ/WRITE command after ACTIVATE command is
- * 2 clocks,
- * - earliest timing for PRECHARGE after last data was read is 1 clock,
- * - earliest timing for PRECHARGE after last data was written is 1 clock,
- * - CAS Latency is 2.
- */
-#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
- PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_3W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-/* With a 16 MB DIMM, the PSDMR is configured as follows:
- *
- * configuration parameters found in Motorola documentation
- */
-#define CONFIG_SYS_PSDMR (0x016EB452)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-#define RS232EN_1 0x02000002
-#define RS232EN_2 0x01000001
-#define FETHIEN 0x08000008
-#define FETH_RST 0x04000004
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */
-/* 0x0EB2B645 */
-#define CONFIG_SYS_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\
- ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\
- ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\
- ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \
- )
-
-/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3) */
-/* #define CONFIG_SYS_HRCW_MASTER 0x0cb23645 */
-
-/* This value should actually be situated in the first 256 bytes of the FLASH
- which on the standard MPC8266ADS board is at address 0xFF800000
- The linker script places it at 0xFFF00000 instead.
-
- It still works, however, as long as the ADS board jumper JP3 is set to
- position 2-3 so the board is using the BCSR as Hardware Configuration Word
-
- If you want to use the one defined here instead, ust copy the first 256 bytes from
- 0xfff00000 to 0xff800000 (for 8MB flash)
-
- - Rune
-
-*/
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-# define CONFIG_ENV_SECT_SIZE 0x40000
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-/*#define CONFIG_SYS_HID0_INIT 0 */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
- HID0_DCE |\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE )
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SYPCR 0xFFFFFFC3
-#define CONFIG_SYS_BCR 0x004C0000
-#define CONFIG_SYS_SIUMCR 0x4E64C000
-#define CONFIG_SYS_SCCR 0x00000000
-
-/* local bus memory map
- *
- * 0x00000000-0x03FFFFFF 64MB SDRAM
- * 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window
- * 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window
- * 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory
- * 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window
- * 0xF8000000-0xF8007FFF 32KB BCSR
- * 0xF8100000-0xF8107FFF 32KB ATM UNI
- * 0xF8200000-0xF8207FFF 32KB PCI interrupt controller
- * 0xF8300000-0xF8307FFF 32KB EEPROM
- * 0xFE000000-0xFFFFFFFF 32MB flash
- */
-#define CONFIG_SYS_BR0_PRELIM 0xFE001801 /* flash */
-#define CONFIG_SYS_OR0_PRELIM 0xFE000836
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR | 0x1801) /* BCSR */
-#define CONFIG_SYS_OR1_PRELIM 0xFFFF8010
-#define CONFIG_SYS_BR4_PRELIM 0xF8300801 /* EEPROM */
-#define CONFIG_SYS_OR4_PRELIM 0xFFFF8846
-#define CONFIG_SYS_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */
-#define CONFIG_SYS_OR5_PRELIM 0xFFFF8E36
-#define CONFIG_SYS_BR8_PRELIM (CONFIG_SYS_PCI_INT | 0x1801) /* PCI interrupt controller */
-#define CONFIG_SYS_OR8_PRELIM 0xFFFF8010
-
-#define CONFIG_SYS_RMR 0x0001
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-#define CONFIG_SYS_RCCR 0
-#define CONFIG_SYS_MPTPR 0x00001900
-#define CONFIG_SYS_PSRT 0x00000021
-
-/* This address must not exist */
-#define CONFIG_SYS_RESET_ADDRESS 0xFCFFFF00
-
-/* PCI Memory map (if different from default map */
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
-#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \
- PICMR_PREFETCH_EN)
-
-/*
- * These are the windows that allow the CPU to access PCI address space.
- * All three PCI master windows, which allow the CPU to access PCI
- * prefetch, non prefetch, and IO space (see below), must all fit within
- * these windows.
- */
-
-/* PCIBR0 */
-#define CONFIG_SYS_PCI_MSTR0_LOCAL 0x80000000 /* Local base */
-#define CONFIG_SYS_PCIMSK0_MASK PCIMSK_1GB /* Size of window */
-/* PCIBR1 */
-#define CONFIG_SYS_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */
-#define CONFIG_SYS_PCIMSK1_MASK PCIMSK_64MB /* Size of window */
-
-/*
- * Master window that allows the CPU to access PCI Memory (prefetch).
- * This window will be setup with the first set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
-
-/*
- * Master window that allows the CPU to access PCI Memory (non-prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
-#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE)
-
-/*
- * Master window that allows the CPU to access PCI IO space.
- * This window will be setup with the third set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */
-#define CONFIG_SYS_PCI_MSTR_IO_BUS 0xF4000000 /* PCI base */
-#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */
-#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO)
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT ""
-#define MTDPARTS_DEFAULT ""
-*/
-
-#endif /* __CONFIG_H */
--
1.9.1
More information about the U-Boot
mailing list