[U-Boot] [PATCH v1] x86: ahci: Make sure interface is not busy after enabling the port

Bin Meng bmeng.cn at gmail.com
Tue Dec 23 09:01:02 CET 2014


Each time U-Boot boots on Intel Crown Bay board, the displayed hard
drive information is wrong. It could be either wrong capacity or just
a 'Capacity: not available' message. After enabling the debug switch,
we can see the scsi inquiry command did not execute successfully.
However, doing a 'scsi scan' in the U-Boot shell does not expose
this issue.

SCSI:  Target spinup took 0 ms.
SATA link 1 timeout.
AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
scanning bus for devices...
ahci_device_data_io: 0 byte transferred.   <--- scsi inquiry fails
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
  Device 0: (0:0) Vendor: ATA Prod.:  Rev: ?8
              Type: Hard Disk
	                  Capacity: 912968.3 MB = 891.5 GB (1869759264 x 512)
			  Found 1 device(s).

So uninitialized contents on the stack were passed to dev_print() to
display those wrong information.

The symptom were observed on two hard drives (one is Seagate, the
other one is Western Digital). The fix is to make sure the AHCI
interface is not busy by checking the error and status information
from task file register after enabling the port in ahci_port_start()
before proceeding other operations like scsi_scan().

Signed-off-by: Bin Meng <bmeng.cn at gmail.com>

---

 drivers/block/ahci.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/drivers/block/ahci.c b/drivers/block/ahci.c
index c9a3beb..7ca8f40 100644
--- a/drivers/block/ahci.c
+++ b/drivers/block/ahci.c
@@ -505,8 +505,9 @@ static int ahci_port_start(u8 port)
 {
 	struct ahci_ioports *pp = &(probe_ent->port[port]);
 	volatile u8 *port_mmio = (volatile u8 *)pp->port_mmio;
-	u32 port_status;
+	u32 port_status, tf_data;
 	u32 mem;
+	int i = 0;
 
 	debug("Enter start port: %d\n", port);
 	port_status = readl(port_mmio + PORT_SCR_STAT);
@@ -564,6 +565,18 @@ static int ahci_port_start(u8 port)
 			  PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
 			  PORT_CMD_START, port_mmio + PORT_CMD);
 
+	/*
+	 * Make sure interface is not busy based on error and status
+	 * information from task file data register before proceeding
+	 */
+	while (i < WAIT_MS_SPINUP) {
+		tf_data = readl(port_mmio + PORT_TFDATA);
+		if (!(tf_data & ATA_BUSY))
+			break;
+		udelay(1000);
+		i++;
+	}
+
 	debug("Exit start port %d\n", port);
 
 	return 0;
-- 
1.8.2.1



More information about the U-Boot mailing list