[U-Boot] [PATCH] nand/denali: Adding Denali NAND driver support

[Chin Liang See]

Hi Rik,

This patch is for U-Boot only.
You might wanna find the kernel patch at
http://rocketboards.org/gitweb/?p=linux-socfpga.git;a=commit;h=23b95d8c25d34afadc82325313f25e72d76c5cef

While for your issue, its quite strange.
Currently, we are using 512 byte sector protected with 8 bit ECC.
With this configuration, we will need around 58 bytes at OOB.
This is to accommodate 2 bytes bad block market +  42 bytes data + 14
bytes ECC.

Wonder you are using different configuration?
Thanks and have a nice day!

Chin Liang


On Fri, 2014-05-30 at 11:06 +0000, Rik Smith wrote:
> Chin,
> 
>    I was wondering which kernel this patch went into or is going into?
> 
> I am having problems with accessing a hynix NAND from an altera
> cyclone V
> using kernel 3.11. It is coming up with a kernel driver error on boot
> of:
> "Your NAND chip OOB is not large enough to contain 8bit ECC correction
> codes"
> 
> Looking for help on this issue.
> 
> Cheers
> Rik
> 
> kernel bootlog extract:
> 
> at24 0-0051: 4096 byte 24c32 EEPROM, writable, 32 bytes/write
> denali-nand-dt ff900000.flash: Dump timing register values:acc_clks:
> 0,
> re_2_we: 50, re_2_re: 50
> we_2_re: 5170, addr_2_data: 5170, rdwr_en_lo_cnt: 18
> rdwr_en_hi_cnt: 12, cs_setup_cnt: 3
> NAND device: Manufacturer ID: 0xad, Chip ID: 0xd5 (Hynix NAND 2GiB
> 3,3V
> 8-bit), 2048MiB, page size: 4096, OOB size: 64
> Your NAND chip OOB is not large enough
> to                              
> contain 8bit ECC correction codes
> cadence-qspi ff705000.flash: DMA NOT enabled
> cadence-qspi ff705000.flash: master is unqueued, this is deprecated
> m25p80 spi2.0: found n25q00, expected n25q512a
> 
> 
> 
> ______________________________________________________________________
> Rik Smith | Senior Software Engineer
> 
> 
>  
> 
> 
> Optos Plc
> Queensferry House
> Carnegie Campus
> Enterprise Way, Dunfermline
> Scotland, UK
> 
> KY11 8GR
> 
>  
> 
> Tel:                 +44 (0)1383 843300
> 
> Dir:                 +44 (0)1383 843427
> 
> Fax:                +44 (0)1383 843333
> 
> Email:              rsmith at optos.com
> 
> Web:              www.optos.com
> 
> 
> 
> 
> 
> 
> Transmission of this email and any files that may be attached is
> confidential and may contain proprietary information, and is intended
> solely for the use of the individual(s) or entity to who it is
> addressed. If you are not the intended recipient, any use including,
> but not limited to, dissemination, printing or copying of the email
> and its attachments is strictly prohibited.If you have received the
> email in error you are requested to contact the sender by telephone
> and permanently delete the material from your system.Any views or
> opinions expressed herein are solely those of the individual sender
> and do not necessarily represent those of Optos plc or its subsidiary
> companies. Precautions have been taken to minimize the risk of
> transmitting software viruses. Optos plc requests virus checks on any
> attachments to this message are carried out by the recipient(s), as no
> responsibility or liability can be assumed for any loss or damage to
> the recipient's computer software or hardware. OPTOS PLC. SC139953.
> REGISTERED OFFICE. QUEENSFERRY HOUSE, CARNEGIE CAMPUS, ENTERPRISE WAY,
> DUNFERMLINE, SCOTLAND, KY11 8GR, UNITED KINGDOM; OPTOS INC. 67 FOREST
> STREET, MARLBOROUGH, MA 01752, USA; OPTOS GmbH. PRINZENALLEE 7,
> D-40549, DÜSSELDORF, GERMANY. GESCHÄFTSFÜHRER: ROY DAVIS, ROBERT
> KENNEDY. AMTSGERICHT MANNHEIM HRB 700 960