[U-Boot] Mainline u-boot SPL for socfpga
Pavel Machek
pavel at denx.de
Tue Jun 3 10:49:48 CEST 2014
Hi!
> > > U-Boot 2014.07-rc1-00079-g2072e72-dirty (May 16 2014 - 15:54:55)
> > >
> > > CPU : Altera SOCFPGA Platform
> > > BOARD : Altera SOCFPGA Cyclone5 Board
> > > DRAM: 1 GiB
> > > WARNING: Caches not enabled
> > > Using default environment
> > >
> > > In: serial
> > > Out: serial
> > > Err: serial
> > > Net: No ethernet found.
> >
> > Do you have any hints how to get ethernet to work?
> >
>
> I yet to upstream the ethernet part yet.
> I plan to do that once I upstreamed all the minimum SPL code to run on
> dev kit.
I tried to get it to work, but did not succeed so far.
First, designware.c patches are for version before rewrite -- so I
reverted to that version. For some reason, it detects phy at all
possible places -- seems like the controller is not listening in the
address space?
Then, it seems ethernet address reading depends on i2c, so I added
that, and that in turn depends on clock framework.
This is what my current diff. If you have any ideas, let me know.
Best regards,
Pavel
diff --git a/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h b/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h
index f564046..c8e925a 100644
--- a/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h
+++ b/arch/arm/include/asm/arch-socfpga/socfpga_base_addrs.h
@@ -14,5 +14,8 @@
#define SOCFPGA_CLKMGR_ADDRESS 0xffd04000
#define SOCFPGA_RSTMGR_ADDRESS 0xffd05000
#define SOCFPGA_SYSMGR_ADDRESS 0xffd08000
+#define SOCFPGA_EMAC0_ADDRESS 0xff700000
+#define SOCFPGA_EMAC1_ADDRESS 0xff702000
+
#endif /* _SOCFPGA_BASE_ADDRS_H_ */
diff --git a/board/altera/socfpga/socfpga_cyclone5.c b/board/altera/socfpga/socfpga_cyclone5.c
index 33946b6..fd68aa9 100644
--- a/board/altera/socfpga/socfpga_cyclone5.c
+++ b/board/altera/socfpga/socfpga_cyclone5.c
@@ -7,11 +7,39 @@
#include <common.h>
#include <asm/arch/reset_manager.h>
#include <asm/io.h>
+#ifndef CONFIG_SPL_BUILD
+#include <phy.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include "../../../drivers/net/designware.h"
+#endif
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
+static const struct socfpga_reset_manager *reset_manager_base =
+ (void *)SOCFPGA_RSTMGR_ADDRESS;
+
+#define RSTMGR_PERMODRST_EMAC0_LSB 0
+#define RSTMGR_PERMODRST_EMAC1_LSB 1
+
+#define CONFIG_SYSMGR_EMAC_CTRL (SOCFPGA_SYSMGR_ADDRESS + 0x60)
+
+/* Enumeration: sysmgr::emacgrp::ctrl::physel::enum */
+#define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII 0x0
+#define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII 0x1
+#define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII 0x2
+#define SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB 0
+#define SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB 2
+#define SYSMGR_EMACGRP_CTRL_PHYSEL_MASK 0x00000003
+
+/* EMAC controller and PHY used */
+#define CONFIG_EMAC_BASE CONFIG_EMAC1_BASE
+#define CONFIG_EPHY_PHY_ADDR CONFIG_EPHY1_PHY_ADDR
+#define CONFIG_PHY_INTERFACE_MODE SOCFPGA_PHYSEL_ENUM_RGMII
+
#if defined(CONFIG_DISPLAY_CPUINFO)
/*
* Print CPU information
@@ -64,8 +92,152 @@ int overwrite_console(void)
/*
* DesignWare Ethernet initialization
*/
+
+int designware_board_phy_init(struct eth_device *dev, int phy_addr,
+ int (*mii_write)(struct eth_device *, u8, u8, u16),
+ int (*dw_reset_phy)(struct eth_device *))
+{
+ struct dw_eth_dev *priv = dev->priv;
+ struct phy_device *phydev;
+ struct mii_dev *bus;
+
+ printf("Back to board file\n");
+
+ if ((*dw_reset_phy)(dev) < 0)
+ return -1;
+
+ bus = mdio_get_current_dev();
+ printf("Board file: bus %lx\n", bus);
+
+ /*
+struct phy_device *phy_find_by_mask(struct mii_dev *bus, unsigned phy_mask,
+phy_interface_t interface)
+ */
+
+ phydev = phy_connect(bus, phy_addr, dev,
+ priv->interface);
+
+ printf("Board file: bus %lx\n", phydev);
+ /* Micrel PHY is connected to EMAC1 */
+ if (strcasecmp(phydev->drv->name, "Micrel ksz9021") == 0 &&
+ ((phydev->drv->uid & phydev->drv->mask) ==
+ (phydev->phy_id & phydev->drv->mask))) {
+
+ printf("Configuring PHY skew timing for %s\n",
+ phydev->drv->name);
+
+ /* min rx data delay */
+ if (ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+ getenv_ulong(CONFIG_KSZ9021_DATA_SKEW_ENV, 16,
+ CONFIG_KSZ9021_DATA_SKEW_VAL)) < 0)
+ return -1;
+ /* min tx data delay */
+ if (ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
+ getenv_ulong(CONFIG_KSZ9021_DATA_SKEW_ENV, 16,
+ CONFIG_KSZ9021_DATA_SKEW_VAL)) < 0)
+ return -1;
+ /* max rx/tx clock delay, min rx/tx control */
+ if (ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+ getenv_ulong(CONFIG_KSZ9021_CLK_SKEW_ENV, 16,
+ CONFIG_KSZ9021_CLK_SKEW_VAL)) < 0)
+ return -1;
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+ }
+ return 0;
+}
+
+/* Change the reset state for EMAC0 */
+void emac0_reset_enable(uint state)
+{
+ if (state)
+ setbits_le32(&reset_manager_base->per_mod_reset,
+ (1 << RSTMGR_PERMODRST_EMAC0_LSB));
+ else
+ clrbits_le32(&reset_manager_base->per_mod_reset,
+ (1 << RSTMGR_PERMODRST_EMAC0_LSB));
+}
+
+/* Change the reset state for EMAC1 */
+void emac1_reset_enable(uint state)
+{
+ if (state)
+ setbits_le32(&reset_manager_base->per_mod_reset,
+ (1 << RSTMGR_PERMODRST_EMAC1_LSB));
+ else
+ clrbits_le32(&reset_manager_base->per_mod_reset,
+ (1 << RSTMGR_PERMODRST_EMAC1_LSB));
+}
+
+
/* We know all the init functions have been run now */
int board_eth_init(bd_t *bis)
{
- return 0;
+ printf("Board_eth_init\n");
+#if !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET) && \
+!defined(CONFIG_SPL_BUILD)
+
+ /* Initialize EMAC */
+
+ /*
+ * Putting the EMAC controller to reset when configuring the PHY
+ * interface select at System Manager
+ */
+ printf("enabling resets...\n");
+ emac0_reset_enable(1);
+ emac1_reset_enable(1);
+
+ /* Clearing emac0 PHY interface select to 0 */
+ clrbits_le32(CONFIG_SYSMGR_EMAC_CTRL,
+ (SYSMGR_EMACGRP_CTRL_PHYSEL_MASK <<
+#if (CONFIG_EMAC_BASE == CONFIG_EMAC0_BASE)
+ SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB));
+#elif (CONFIG_EMAC_BASE == CONFIG_EMAC1_BASE)
+ SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB));
+#endif
+
+ /* configure to PHY interface select choosed */
+ setbits_le32(CONFIG_SYSMGR_EMAC_CTRL,
+#if (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_GMII)
+ (SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII <<
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_MII)
+ (SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII <<
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_RGMII)
+ (SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII <<
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_RMII)
+ (SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII <<
+#endif
+#if (CONFIG_EMAC_BASE == CONFIG_EMAC0_BASE)
+ SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB));
+ printf("enabling emac0...\n");
+ /* Release the EMAC controller from reset */
+ emac0_reset_enable(0);
+#elif (CONFIG_EMAC_BASE == CONFIG_EMAC1_BASE)
+ SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB));
+ printf("enabling emac1...\n");
+ /* Release the EMAC controller from reset */
+ emac1_reset_enable(0);
+#endif
+
+ /* initialize and register the emac */
+ int rval = designware_initialize(0, CONFIG_EMAC_BASE,
+ CONFIG_EPHY_PHY_ADDR,
+#if (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_GMII)
+ PHY_INTERFACE_MODE_GMII);
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_MII)
+ PHY_INTERFACE_MODE_MII);
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_RGMII)
+ PHY_INTERFACE_MODE_RGMII);
+#elif (CONFIG_PHY_INTERFACE_MODE == SOCFPGA_PHYSEL_ENUM_RMII)
+ PHY_INTERFACE_MODE_RMII);
+#endif
+ printf("board_eth_init %d\n", rval);
+ return rval;
+#else
+ return 0;
+#endif
}
diff --git a/board/bf609-ezkit/bf609-ezkit.c b/board/bf609-ezkit/bf609-ezkit.c
index 43a4330..cfc64fe 100644
--- a/board/bf609-ezkit/bf609-ezkit.c
+++ b/board/bf609-ezkit/bf609-ezkit.c
@@ -41,12 +41,12 @@ int board_eth_init(bd_t *bis)
if (CONFIG_DW_PORTS & 1) {
static const unsigned short pins[] = P_RMII0;
if (!peripheral_request_list(pins, "emac0"))
- ret += designware_initialize(EMAC0_MACCFG, 0);
+ ret += designware_initialize(0, EMAC0_MACCFG, 1, 0);
}
if (CONFIG_DW_PORTS & 2) {
static const unsigned short pins[] = P_RMII1;
if (!peripheral_request_list(pins, "emac1"))
- ret += designware_initialize(EMAC1_MACCFG, 0);
+ ret += designware_initialize(1, EMAC1_MACCFG, 1, 0);
}
return ret;
diff --git a/board/spear/spear300/spear300.c b/board/spear/spear300/spear300.c
index 6b6bd9f..e25aba2 100644
--- a/board/spear/spear300/spear300.c
+++ b/board/spear/spear300/spear300.c
@@ -53,7 +53,8 @@ int board_eth_init(bd_t *bis)
#if defined(CONFIG_DESIGNWARE_ETH)
u32 interface = PHY_INTERFACE_MODE_MII;
- if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
+ if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
+ interface) >= 0)
ret++;
#endif
return ret;
diff --git a/board/spear/spear310/spear310.c b/board/spear/spear310/spear310.c
index a4c6a8e..70f9aa1 100644
--- a/board/spear/spear310/spear310.c
+++ b/board/spear/spear310/spear310.c
@@ -54,7 +54,8 @@ int board_eth_init(bd_t *bis)
#if defined(CONFIG_DESIGNWARE_ETH)
u32 interface = PHY_INTERFACE_MODE_MII;
- if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
+ if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
+ interface) >= 0)
ret++;
#endif
#if defined(CONFIG_MACB)
diff --git a/board/spear/spear320/spear320.c b/board/spear/spear320/spear320.c
index ab732a7..f6b1fdd 100644
--- a/board/spear/spear320/spear320.c
+++ b/board/spear/spear320/spear320.c
@@ -65,7 +65,8 @@ int board_eth_init(bd_t *bis)
#if defined(CONFIG_DESIGNWARE_ETH)
u32 interface = PHY_INTERFACE_MODE_MII;
- if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
+ if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
+ interface) >= 0)
ret++;
#endif
#if defined(CONFIG_MACB)
diff --git a/board/spear/spear600/spear600.c b/board/spear/spear600/spear600.c
index 8472002..e996a0e 100644
--- a/board/spear/spear600/spear600.c
+++ b/board/spear/spear600/spear600.c
@@ -51,7 +51,8 @@ int board_eth_init(bd_t *bis)
#if defined(CONFIG_DW_AUTONEG)
interface = PHY_INTERFACE_MODE_GMII;
#endif
- if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
+ if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
+ interface) >= 0)
ret++;
#endif
return ret;
diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c
index b8edfcd..044d204 100644
--- a/board/spear/x600/x600.c
+++ b/board/spear/x600/x600.c
@@ -67,32 +67,31 @@ void board_nand_init(void)
fsmc_nand_init(nand);
}
-int board_phy_config(struct phy_device *phydev)
+int designware_board_phy_init(struct eth_device *dev, int phy_addr,
+ int (*mii_write)(struct eth_device *, u8, u8, u16),
+ int dw_reset_phy(struct eth_device *))
{
/* Extended PHY control 1, select GMII */
- phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
+ mii_write(dev, phy_addr, 23, 0x0020);
/* Software reset necessary after GMII mode selction */
- phy_reset(phydev);
+ dw_reset_phy(dev);
/* Enable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
+ mii_write(dev, phy_addr, 31, 0x0001);
/* 17e: Enhanced LED behavior, needs to be written twice */
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+ mii_write(dev, phy_addr, 17, 0x09ff);
+ mii_write(dev, phy_addr, 17, 0x09ff);
/* 16e: Enhanced LED method select */
- phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
+ mii_write(dev, phy_addr, 16, 0xe0ea);
/* Disable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
+ mii_write(dev, phy_addr, 31, 0x0000);
/* Enable clock output pin */
- phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
+ mii_write(dev, phy_addr, 18, 0x0049);
return 0;
}
@@ -101,7 +100,7 @@ int board_eth_init(bd_t *bis)
{
int ret = 0;
- if (designware_initialize(CONFIG_SPEAR_ETHBASE,
+ if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_PHY_ADDR,
PHY_INTERFACE_MODE_GMII) >= 0)
ret++;
diff --git a/drivers/net/designware.c b/drivers/net/designware.c
index 78751b2..965b033 100644
--- a/drivers/net/designware.c
+++ b/drivers/net/designware.c
@@ -17,75 +17,7 @@
#include <asm/io.h>
#include "designware.h"
-#if !defined(CONFIG_PHYLIB)
-# error "DesignWare Ether MAC requires PHYLIB - missing CONFIG_PHYLIB"
-#endif
-
-static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
-{
- struct eth_mac_regs *mac_p = bus->priv;
- ulong start;
- u16 miiaddr;
- int timeout = CONFIG_MDIO_TIMEOUT;
-
- miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
- ((reg << MIIREGSHIFT) & MII_REGMSK);
-
- writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
-
- start = get_timer(0);
- while (get_timer(start) < timeout) {
- if (!(readl(&mac_p->miiaddr) & MII_BUSY))
- return readl(&mac_p->miidata);
- udelay(10);
- };
-
- return -1;
-}
-
-static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
- u16 val)
-{
- struct eth_mac_regs *mac_p = bus->priv;
- ulong start;
- u16 miiaddr;
- int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
-
- writel(val, &mac_p->miidata);
- miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
- ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
-
- writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
-
- start = get_timer(0);
- while (get_timer(start) < timeout) {
- if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
- ret = 0;
- break;
- }
- udelay(10);
- };
-
- return ret;
-}
-
-static int dw_mdio_init(char *name, struct eth_mac_regs *mac_regs_p)
-{
- struct mii_dev *bus = mdio_alloc();
-
- if (!bus) {
- printf("Failed to allocate MDIO bus\n");
- return -1;
- }
-
- bus->read = dw_mdio_read;
- bus->write = dw_mdio_write;
- sprintf(bus->name, name);
-
- bus->priv = (void *)mac_regs_p;
-
- return mdio_register(bus);
-}
+static int configure_phy(struct eth_device *dev);
static void tx_descs_init(struct eth_device *dev)
{
@@ -170,59 +102,53 @@ static void rx_descs_init(struct eth_device *dev)
priv->rx_currdescnum = 0;
}
-static int dw_write_hwaddr(struct eth_device *dev)
+static void descs_init(struct eth_device *dev)
{
- struct dw_eth_dev *priv = dev->priv;
- struct eth_mac_regs *mac_p = priv->mac_regs_p;
- u32 macid_lo, macid_hi;
- u8 *mac_id = &dev->enetaddr[0];
-
- macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
- (mac_id[3] << 24);
- macid_hi = mac_id[4] + (mac_id[5] << 8);
-
- writel(macid_hi, &mac_p->macaddr0hi);
- writel(macid_lo, &mac_p->macaddr0lo);
-
- return 0;
+ tx_descs_init(dev);
+ rx_descs_init(dev);
}
-static void dw_adjust_link(struct eth_mac_regs *mac_p,
- struct phy_device *phydev)
+static int mac_reset(struct eth_device *dev)
{
- u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN;
+ struct dw_eth_dev *priv = dev->priv;
+ struct eth_mac_regs *mac_p = priv->mac_regs_p;
+ struct eth_dma_regs *dma_p = priv->dma_regs_p;
- if (!phydev->link) {
- printf("%s: No link.\n", phydev->dev->name);
- return;
- }
+ ulong start;
+ int timeout = CONFIG_MACRESET_TIMEOUT;
- if (phydev->speed != 1000)
- conf |= MII_PORTSELECT;
+ writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
- if (phydev->speed == 100)
- conf |= FES_100;
+ if (priv->interface != PHY_INTERFACE_MODE_RGMII)
+ writel(MII_PORTSELECT, &mac_p->conf);
- if (phydev->duplex)
- conf |= FULLDPLXMODE;
+ start = get_timer(0);
+ while (get_timer(start) < timeout) {
+ if (!(readl(&dma_p->busmode) & DMAMAC_SRST))
+ return 0;
- writel(conf, &mac_p->conf);
+ /* Try again after 10usec */
+ udelay(10);
+ };
- printf("Speed: %d, %s duplex%s\n", phydev->speed,
- (phydev->duplex) ? "full" : "half",
- (phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
+ return -1;
}
-static void dw_eth_halt(struct eth_device *dev)
+static int dw_write_hwaddr(struct eth_device *dev)
{
struct dw_eth_dev *priv = dev->priv;
struct eth_mac_regs *mac_p = priv->mac_regs_p;
- struct eth_dma_regs *dma_p = priv->dma_regs_p;
+ u32 macid_lo, macid_hi;
+ u8 *mac_id = &dev->enetaddr[0];
- writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf);
- writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode);
+ macid_lo = mac_id[0] + (mac_id[1] << 8) + \
+ (mac_id[2] << 16) + (mac_id[3] << 24);
+ macid_hi = mac_id[4] + (mac_id[5] << 8);
- phy_shutdown(priv->phydev);
+ writel(macid_hi, &mac_p->macaddr0hi);
+ writel(macid_lo, &mac_p->macaddr0lo);
+
+ return 0;
}
static int dw_eth_init(struct eth_device *dev, bd_t *bis)
@@ -230,43 +156,60 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis)
struct dw_eth_dev *priv = dev->priv;
struct eth_mac_regs *mac_p = priv->mac_regs_p;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
- unsigned int start;
+ u32 conf;
- writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
+ if (priv->phy_configured != 1) {
+ int ret = configure_phy(dev);
+ if (ret < 0) {
+ printf("failed to configure phy: %d\n", ret);
+ return ret;
+ }
+ }
- start = get_timer(0);
- while (readl(&dma_p->busmode) & DMAMAC_SRST) {
- if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT)
- return -1;
+ /* Print link status only once */
+ if (!priv->link_printed) {
+ printf("ENET Speed is %d Mbps - %s duplex connection\n",
+ priv->speed, (priv->duplex == HALF) ? "HALF" : "FULL");
+ priv->link_printed = 1;
+ }
- mdelay(100);
- };
+ /* Reset ethernet hardware */
+ if (mac_reset(dev) < 0)
+ return -1;
- /* Soft reset above clears HW address registers.
- * So we have to set it here once again */
+ /* Resore the HW MAC address as it has been lost during MAC reset */
dw_write_hwaddr(dev);
- rx_descs_init(dev);
- tx_descs_init(dev);
+ writel(FIXEDBURST | PRIORXTX_41 | BURST_16,
+ &dma_p->busmode);
- writel(FIXEDBURST | PRIORXTX_41 | BURST_16, &dma_p->busmode);
+ writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD |
+ TXSECONDFRAME, &dma_p->opmode);
- writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD,
- &dma_p->opmode);
+ conf = FRAMEBURSTENABLE | DISABLERXOWN;
- writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode);
+ if (priv->speed != 1000)
+ conf |= MII_PORTSELECT;
- /* Start up the PHY */
- if (phy_startup(priv->phydev)) {
- printf("Could not initialize PHY %s\n",
- priv->phydev->dev->name);
- return -1;
+ if ((priv->interface != PHY_INTERFACE_MODE_MII) &&
+ (priv->interface != PHY_INTERFACE_MODE_GMII)) {
+
+ if (priv->speed == 100)
+ conf |= FES_100;
}
- dw_adjust_link(mac_p, priv->phydev);
+ if (priv->duplex == FULL)
+ conf |= FULLDPLXMODE;
- if (!priv->phydev->link)
- return -1;
+ writel(conf, &mac_p->conf);
+
+ descs_init(dev);
+
+ /*
+ * Start/Enable xfer at dma as well as mac level
+ */
+ writel(readl(&dma_p->opmode) | RXSTART, &dma_p->opmode);
+ writel(readl(&dma_p->opmode) | TXSTART, &dma_p->opmode);
writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
@@ -376,36 +319,271 @@ static int dw_eth_recv(struct eth_device *dev)
return length;
}
-static int dw_phy_init(struct eth_device *dev)
+static void dw_eth_halt(struct eth_device *dev)
{
struct dw_eth_dev *priv = dev->priv;
- struct phy_device *phydev;
- int mask = 0xffffffff;
-#ifdef CONFIG_PHY_ADDR
- mask = 1 << CONFIG_PHY_ADDR;
+ mac_reset(dev);
+ priv->tx_currdescnum = priv->rx_currdescnum = 0;
+}
+
+static int eth_mdio_read(struct eth_device *dev, u8 addr, u8 reg, u16 *val)
+{
+ struct dw_eth_dev *priv = dev->priv;
+ struct eth_mac_regs *mac_p = priv->mac_regs_p;
+ ulong start;
+ u32 miiaddr;
+ int timeout = CONFIG_MDIO_TIMEOUT;
+
+ miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \
+ ((reg << MIIREGSHIFT) & MII_REGMSK);
+
+ writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
+
+ start = get_timer(0);
+ while (get_timer(start) < timeout) {
+ if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
+ *val = readl(&mac_p->miidata);
+ return 0;
+ }
+
+ /* Try again after 10usec */
+ udelay(10);
+ };
+
+ return -1;
+}
+
+static int eth_mdio_write(struct eth_device *dev, u8 addr, u8 reg, u16 val)
+{
+ struct dw_eth_dev *priv = dev->priv;
+ struct eth_mac_regs *mac_p = priv->mac_regs_p;
+ ulong start;
+ u32 miiaddr;
+ int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
+ u16 value;
+
+ printf("eth_mdio_write %lx\n", &mac_p->miidata);
+
+ writel(val, &mac_p->miidata);
+ miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \
+ ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
+
+ writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
+
+ start = get_timer(0);
+ while (get_timer(start) < timeout) {
+ if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
+ ret = 0;
+ break;
+ }
+
+ /* Try again after 10usec */
+ udelay(10);
+ };
+
+ /* Needed as a fix for ST-Phy */
+ eth_mdio_read(dev, addr, reg, &value);
+
+ return ret;
+}
+
+#if defined(CONFIG_DW_SEARCH_PHY)
+static int find_phy(struct eth_device *dev)
+{
+ int phy_addr = 1;
+ u16 ctrl, oldctrl;
+
+ do {
+ printf("Searching at %d\n", phy_addr);
+ eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
+ oldctrl = ctrl & BMCR_ANENABLE;
+
+ ctrl ^= BMCR_ANENABLE;
+ eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl);
+ eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
+ ctrl &= BMCR_ANENABLE;
+
+ if (ctrl == oldctrl) {
+ phy_addr++;
+ } else {
+ ctrl ^= BMCR_ANENABLE;
+ eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl);
+ printf("Found at %d\n", phy_addr);
+
+ return phy_addr;
+ }
+ } while (phy_addr < 32);
+
+ return -1;
+}
+#endif
+
+static int dw_reset_phy(struct eth_device *dev)
+{
+ struct dw_eth_dev *priv = dev->priv;
+ u16 ctrl;
+ ulong start;
+ int timeout = CONFIG_PHYRESET_TIMEOUT;
+ u32 phy_addr = priv->address;
+
+ eth_mdio_write(dev, phy_addr, MII_BMCR, BMCR_RESET);
+
+ start = get_timer(0);
+ while (get_timer(start) < timeout) {
+ eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
+ if (!(ctrl & BMCR_RESET))
+ break;
+
+ /* Try again after 10usec */
+ udelay(10);
+ };
+
+ if (get_timer(start) >= CONFIG_PHYRESET_TIMEOUT) {
+ printf("timed out waiting for phy reset %x\n", ctrl);
+ return -1;
+ }
+
+ // phydev->supported &= PHY_GBIT_FEATURES;
+#ifdef CONFIG_PHY_RESET_DELAY
+ udelay(CONFIG_PHY_RESET_DELAY);
+#endif
+ return 0;
+}
+
+/*
+ * Add weak default function for board specific PHY configuration
+ */
+int __weak designware_board_phy_init(struct eth_device *dev, int phy_addr,
+ int (*mii_write)(struct eth_device *, u8, u8, u16),
+ int dw_reset_phy(struct eth_device *))
+{
+ return 0;
+}
+
+static int configure_phy(struct eth_device *dev)
+{
+ struct dw_eth_dev *priv = dev->priv;
+ int phy_addr;
+ u16 bmcr;
+#if defined(CONFIG_DW_AUTONEG)
+ u16 bmsr;
+ u32 timeout;
+ ulong start;
#endif
- phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
- if (!phydev)
+ printf("configure_phy\n");
+
+#if defined(CONFIG_DW_SEARCH_PHY)
+ printf("finding phy\n");
+ phy_addr = find_phy(dev);
+ if (phy_addr >= 0)
+ priv->address = phy_addr;
+ else
+ return -1;
+#else
+ phy_addr = priv->address;
+#endif
+
+ /*
+ * Some boards need board specific PHY initialization. This is
+ * after the main driver init code but before the auto negotiation
+ * is run.
+ */
+ if (designware_board_phy_init(dev, phy_addr,
+ eth_mdio_write, dw_reset_phy) < 0)
+ return -1;
+
+#if 0
+ if (dw_reset_phy(dev) < 0)
return -1;
+#endif
- phy_connect_dev(phydev, dev);
+#if defined(CONFIG_DW_AUTONEG)
+ /* Set Auto-Neg Advertisement capabilities to 10/100 half/full */
+ eth_mdio_write(dev, phy_addr, MII_ADVERTISE, 0x1E1);
- phydev->supported &= PHY_GBIT_FEATURES;
- phydev->advertising = phydev->supported;
+ bmcr = BMCR_ANENABLE | BMCR_ANRESTART;
+#else
+ bmcr = BMCR_SPEED100 | BMCR_FULLDPLX;
- priv->phydev = phydev;
- phy_config(phydev);
+#if defined(CONFIG_DW_SPEED10M)
+ bmcr &= ~BMCR_SPEED100;
+#endif
+#if defined(CONFIG_DW_DUPLEXHALF)
+ bmcr &= ~BMCR_FULLDPLX;
+#endif
+#endif
+ if (eth_mdio_write(dev, phy_addr, MII_BMCR, bmcr) < 0)
+ return -1;
- return 1;
+ /* Read the phy status register and populate priv structure */
+#if defined(CONFIG_DW_AUTONEG)
+ timeout = CONFIG_AUTONEG_TIMEOUT;
+ start = get_timer(0);
+ puts("Waiting for PHY auto negotiation to complete");
+ while (get_timer(start) < timeout) {
+ eth_mdio_read(dev, phy_addr, MII_BMSR, &bmsr);
+ if (bmsr & BMSR_ANEGCOMPLETE) {
+ priv->phy_configured = 1;
+ break;
+ }
+
+ /* Print dot all 1s to show progress */
+ if ((get_timer(start) % 1000) == 0)
+ putc('.');
+
+ /* Try again after 1msec */
+ udelay(1000);
+ };
+
+ if (!(bmsr & BMSR_ANEGCOMPLETE))
+ puts(" TIMEOUT!\n");
+ else
+ puts(" done\n");
+#else
+ priv->phy_configured = 1;
+#endif
+
+#ifndef CONFIG_MII
+#error Need config_phy
+#endif
+ priv->speed = miiphy_speed(dev->name, phy_addr);
+ priv->duplex = miiphy_duplex(dev->name, phy_addr);
+
+ return 0;
}
-int designware_initialize(ulong base_addr, u32 interface)
+#if defined(CONFIG_MII)
+static int dw_mii_read(const char *devname, u8 addr, u8 reg, u16 *val)
+{
+ struct eth_device *dev;
+
+ dev = eth_get_dev_by_name(devname);
+ if (dev)
+ eth_mdio_read(dev, addr, reg, val);
+
+ return 0;
+}
+
+static int dw_mii_write(const char *devname, u8 addr, u8 reg, u16 val)
+{
+ struct eth_device *dev;
+
+ dev = eth_get_dev_by_name(devname);
+ if (dev)
+ eth_mdio_write(dev, addr, reg, val);
+
+ return 0;
+}
+#endif
+
+int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface)
{
struct eth_device *dev;
struct dw_eth_dev *priv;
+ printf("dw_initalize\n");
dev = (struct eth_device *) malloc(sizeof(struct eth_device));
if (!dev)
return -ENOMEM;
@@ -423,14 +601,20 @@ int designware_initialize(ulong base_addr, u32 interface)
memset(dev, 0, sizeof(struct eth_device));
memset(priv, 0, sizeof(struct dw_eth_dev));
- sprintf(dev->name, "dwmac.%lx", base_addr);
+ sprintf(dev->name, "mii%d", id);
dev->iobase = (int)base_addr;
dev->priv = priv;
+ printf("Get address\n");
+ eth_getenv_enetaddr_by_index("eth", id, &dev->enetaddr[0]);
+
priv->dev = dev;
priv->mac_regs_p = (struct eth_mac_regs *)base_addr;
priv->dma_regs_p = (struct eth_dma_regs *)(base_addr +
DW_DMA_BASE_OFFSET);
+ priv->address = phy_addr;
+ priv->phy_configured = 0;
+ priv->interface = interface;
dev->init = dw_eth_init;
dev->send = dw_eth_send;
@@ -438,12 +622,13 @@ int designware_initialize(ulong base_addr, u32 interface)
dev->halt = dw_eth_halt;
dev->write_hwaddr = dw_write_hwaddr;
+ printf("Get eth register\n");
eth_register(dev);
- priv->interface = interface;
+#if defined(CONFIG_MII)
+ printf("Get eth miiphy_register\n");
- dw_mdio_init(dev->name, priv->mac_regs_p);
- priv->bus = miiphy_get_dev_by_name(dev->name);
-
- return dw_phy_init(dev);
+ miiphy_register(dev->name, dw_mii_read, dw_mii_write);
+#endif
+ return 1;
}
diff --git a/drivers/net/designware.h b/drivers/net/designware.h
index 382b0c7..60b1103 100644
--- a/drivers/net/designware.h
+++ b/drivers/net/designware.h
@@ -16,6 +16,8 @@
#define CONFIG_MACRESET_TIMEOUT (3 * CONFIG_SYS_HZ)
#define CONFIG_MDIO_TIMEOUT (3 * CONFIG_SYS_HZ)
+#define CONFIG_PHYRESET_TIMEOUT (3 * CONFIG_SYS_HZ)
+#define CONFIG_AUTONEG_TIMEOUT (5 * CONFIG_SYS_HZ)
struct eth_mac_regs {
u32 conf; /* 0x00 */
@@ -215,9 +217,14 @@ struct dmamacdescr {
#endif
struct dw_eth_dev {
+ u32 address;
u32 interface;
+ u32 speed;
+ u32 duplex;
u32 tx_currdescnum;
u32 rx_currdescnum;
+ u32 phy_configured;
+ u32 link_printed;
struct dmamacdescr tx_mac_descrtable[CONFIG_TX_DESCR_NUM];
struct dmamacdescr rx_mac_descrtable[CONFIG_RX_DESCR_NUM];
@@ -229,8 +236,15 @@ struct dw_eth_dev {
struct eth_dma_regs *dma_regs_p;
struct eth_device *dev;
- struct phy_device *phydev;
- struct mii_dev *bus;
};
+/* Speed specific definitions */
+#define SPEED_10M 1
+#define SPEED_100M 2
+#define SPEED_1000M 3
+
+/* Duplex mode specific definitions */
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
#endif
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 5d7e3be..506efb2 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -53,6 +53,8 @@ static struct phy_driver KS8721_driver = {
static int ksz90xx_startup(struct phy_device *phydev)
{
unsigned phy_ctl;
+
+ printf("ksz90xx_startup\n");
genphy_update_link(phydev);
phy_ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_KSZ90xx_PHY_CTL);
@@ -215,6 +217,7 @@ static struct phy_driver ksz9031_driver = {
int phy_micrel_init(void)
{
+ printf("phy_micrel_init\n");
phy_register(&KSZ804_driver);
#ifdef CONFIG_PHY_MICREL_KSZ9021
phy_register(&ksz9021_driver);
diff --git a/include/configs/bf609-ezkit.h b/include/configs/bf609-ezkit.h
index 12192ff..1a43e1b 100644
--- a/include/configs/bf609-ezkit.h
+++ b/include/configs/bf609-ezkit.h
@@ -72,13 +72,12 @@
#define CONFIG_NET_MULTI
#define CONFIG_HOSTNAME "bf609-ezkit"
#define CONFIG_DESIGNWARE_ETH
-#define CONFIG_PHY_ADDR 1
#define CONFIG_DW_PORTS 1
+#define CONFIG_DW_AUTONEG
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_MII
-#define CONFIG_PHYLIB
/* i2c Settings */
#define CONFIG_BFIN_TWI_I2C
diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h
index 56f993a..ded6cb6 100644
--- a/include/configs/socfpga_common.h
+++ b/include/configs/socfpga_common.h
@@ -206,6 +206,46 @@
#define CONFIG_ENV_IS_NOWHERE
/*
+ * network support
+ */
+#ifndef CONFIG_SOCFPGA_VIRTUAL_TARGET
+#define CONFIG_DESIGNWARE_ETH 1
+#endif
+
+#ifdef CONFIG_DESIGNWARE_ETH
+#define CONFIG_EMAC0_BASE SOCFPGA_EMAC0_ADDRESS
+#define CONFIG_EMAC1_BASE SOCFPGA_EMAC1_ADDRESS
+/* console support for network */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+/* designware */
+#define CONFIG_NET_MULTI
+#define CONFIG_DW_ALTDESCRIPTOR
+#define CONFIG_DW_SEARCH_PHY
+#define CONFIG_MII
+#define CONFIG_PHY_GIGE
+#define CONFIG_DW_AUTONEG
+#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+/* phy */
+#define CONFIG_EPHY0_PHY_ADDR 0
+#define CONFIG_EPHY1_PHY_ADDR 4
+#define CONFIG_KSZ9021_CLK_SKEW_ENV "micrel-ksz9021-clk-skew"
+#define CONFIG_KSZ9021_CLK_SKEW_VAL 0xf0f0
+#define CONFIG_KSZ9021_DATA_SKEW_ENV "micrel-ksz9021-data-skew"
+#define CONFIG_KSZ9021_DATA_SKEW_VAL 0x0
+/* Type of PHY available */
+#define SOCFPGA_PHYSEL_ENUM_GMII 0x0
+#define SOCFPGA_PHYSEL_ENUM_MII 0x1
+#define SOCFPGA_PHYSEL_ENUM_RGMII 0x2
+#define SOCFPGA_PHYSEL_ENUM_RMII 0x3
+#endif /* CONFIG_DESIGNWARE_ETH */
+
+/*
* SPL "Second Program Loader" aka Initial Software
*/
diff --git a/include/configs/spear-common.h b/include/configs/spear-common.h
index c0eba37..55f100a 100644
--- a/include/configs/spear-common.h
+++ b/include/configs/spear-common.h
@@ -17,9 +17,11 @@
/* Ethernet driver configuration */
#define CONFIG_MII
#define CONFIG_DESIGNWARE_ETH
+#define CONFIG_DW_SEARCH_PHY
+#define CONFIG_DW0_PHY 1
#define CONFIG_NET_MULTI
-#define CONFIG_PHYLIB
#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
+#define CONFIG_DW_AUTONEG
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
/* USBD driver configuration */
diff --git a/include/configs/spear6xx_evb.h b/include/configs/spear6xx_evb.h
index 28dddcc..7f4dc58 100644
--- a/include/configs/spear6xx_evb.h
+++ b/include/configs/spear6xx_evb.h
@@ -37,9 +37,6 @@
#define CONFIG_SYS_FSMC_NAND_8BIT
#define CONFIG_SYS_NAND_BASE 0xD2000000
-/* Ethernet PHY configuration */
-#define CONFIG_PHY_NATSEMI
-
/* Environment Settings */
#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_USBTTY
diff --git a/include/netdev.h b/include/netdev.h
index e211f18..72a0503 100644
--- a/include/netdev.h
+++ b/include/netdev.h
@@ -36,7 +36,7 @@ int calxedaxgmac_initialize(u32 id, ulong base_addr);
int cs8900_initialize(u8 dev_num, int base_addr);
int davinci_emac_initialize(void);
int dc21x4x_initialize(bd_t *bis);
-int designware_initialize(ulong base_addr, u32 interface);
+int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface);
int dm9000_initialize(bd_t *bis);
int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr);
int e1000_initialize(bd_t *bis);
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
More information about the U-Boot
mailing list