[U-Boot] [PATCH 2/5] sunxi: Add i2c support

[Albert ARIBAUD]

Hi Hans,

On Mon,  9 Jun 2014 17:15:27 +0200, Hans de Goede <hdegoede at redhat.com>
wrote:

> Add support for the i2c controller found on all Allwinner sunxi SoCs,
> this is the same controller as found on the Marvell orion5x and kirkwood
> SoC families, with a slightly different register layout, so this patch uses
> the existing mvtwsi code.

Should not affect orion or kirkwood, since you're just adding a
variant to the "include switch case" where it was intended; but just in
case, I'm Cc:ing Prafulla here.

> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> Acked-by: Ian Campbell <ijc at hellion.org.uk>
> ---
>  arch/arm/cpu/armv7/sunxi/board.c        |  6 ++++++
>  arch/arm/cpu/armv7/sunxi/u-boot-spl.lds |  5 +++++
>  arch/arm/include/asm/arch-sunxi/i2c.h   | 15 +++++++++++++++
>  board/sunxi/board.c                     |  7 +++++++
>  drivers/i2c/mvtwsi.c                    | 18 ++++++++++++++++++
>  include/configs/sunxi-common.h          |  8 ++++++++
>  6 files changed, 59 insertions(+)
>  create mode 100644 arch/arm/include/asm/arch-sunxi/i2c.h
> 
> diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
> index 1e506b5..024c8c1 100644
> --- a/arch/arm/cpu/armv7/sunxi/board.c
> +++ b/arch/arm/cpu/armv7/sunxi/board.c
> @@ -11,6 +11,7 @@
>   */
>  
>  #include <common.h>
> +#include <i2c.h>
>  #include <netdev.h>
>  #include <miiphy.h>
>  #include <serial.h>
> @@ -91,11 +92,16 @@ void s_init(void)
>  	clock_init();
>  	timer_init();
>  	gpio_init();
> +	i2c_init_board();
>  
>  #ifdef CONFIG_SPL_BUILD
>  	gd = &gdata;
>  	preloader_console_init();
>  
> +#ifdef CONFIG_SPL_I2C_SUPPORT
> +	/* Needed early by sunxi_board_init if PMU is enabled */
> +	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> +#endif
>  	sunxi_board_init();
>  #endif
>  }
> diff --git a/arch/arm/cpu/armv7/sunxi/u-boot-spl.lds b/arch/arm/cpu/armv7/sunxi/u-boot-spl.lds
> index c1ae227..53f0cbd 100644
> --- a/arch/arm/cpu/armv7/sunxi/u-boot-spl.lds
> +++ b/arch/arm/cpu/armv7/sunxi/u-boot-spl.lds
> @@ -39,6 +39,11 @@ SECTIONS
>  	.data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
>  
>  	. = ALIGN(4);
> +	.u_boot_list : {
> +		KEEP(*(SORT(.u_boot_list*)));
> +	} > .sram
> +
> +	. = ALIGN(4);

This adds the U-Boot commands section to an SPL linker script, which
seems to imply it was not there before. Are you actually adding command
line to the SPL of this board family?

>  	__image_copy_end = .;
>  	_end = .;
>  
> diff --git a/arch/arm/include/asm/arch-sunxi/i2c.h b/arch/arm/include/asm/arch-sunxi/i2c.h
> new file mode 100644
> index 0000000..dc5406b
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-sunxi/i2c.h
> @@ -0,0 +1,15 @@
> +/*
> + * Copyright 2014 - Hans de Goede <hdegoede at redhat.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +#ifndef _SUNXI_I2C_H_
> +#define _SUNXI_I2C_H_
> +
> +#include <asm/arch/cpu.h>
> +
> +#define CONFIG_I2C_MVTWSI_BASE	SUNXI_TWI0_BASE
> +/* This is abp0-clk on sun4i/5i/7i / abp1-clk on sun6i/sun8i which is 24MHz */
> +#define CONFIG_SYS_TCLK		24000000
> +
> +#endif
> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
> index b05d0b9..543b809 100644
> --- a/board/sunxi/board.c
> +++ b/board/sunxi/board.c
> @@ -106,6 +106,13 @@ int board_mmc_init(bd_t *bis)
>  }
>  #endif
>  
> +void i2c_init_board(void)
> +{
> +	sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUNXI_GPB0_TWI0);
> +	sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUNXI_GPB0_TWI0);
> +	clock_twi_onoff(0, 1);
> +}
> +
>  #ifdef CONFIG_SPL_BUILD
>  void sunxi_board_init(void)
>  {
> diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
> index d3457b9..ad1ce8f 100644
> --- a/drivers/i2c/mvtwsi.c
> +++ b/drivers/i2c/mvtwsi.c
> @@ -22,6 +22,8 @@
>  #include <asm/arch/orion5x.h>
>  #elif defined(CONFIG_KIRKWOOD)
>  #include <asm/arch/kirkwood.h>
> +#elif defined(CONFIG_SUNXI)
> +#include <asm/arch/i2c.h>
>  #else
>  #error Driver mvtwsi not supported by SoC or board
>  #endif
> @@ -30,6 +32,20 @@
>   * TWSI register structure
>   */
>  
> +#ifdef CONFIG_SUNXI
> +
> +struct  mvtwsi_registers {
> +	u32 slave_address;
> +	u32 xtnd_slave_addr;
> +	u32 data;
> +	u32 control;
> +	u32 status;
> +	u32 baudrate;
> +	u32 soft_reset;
> +};
> +
> +#else
> +
>  struct  mvtwsi_registers {
>  	u32 slave_address;
>  	u32 data;
> @@ -43,6 +59,8 @@ struct  mvtwsi_registers {
>  	u32 soft_reset;
>  };
>  
> +#endif
> +
>  /*
>   * Control register fields
>   */
> diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
> index 3f04890..42b0d2e 100644
> --- a/include/configs/sunxi-common.h
> +++ b/include/configs/sunxi-common.h
> @@ -161,6 +161,14 @@
>  #undef CONFIG_CMD_NET
>  #undef CONFIG_CMD_NFS
>  
> +/* I2C */
> +#define CONFIG_SPL_I2C_SUPPORT
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MVTWSI
> +#define CONFIG_SYS_I2C_SPEED		400000
> +#define CONFIG_SYS_I2C_SLAVE		0x7f
> +#define CONFIG_CMD_I2C
> +
>  #ifndef CONFIG_CONS_INDEX
>  #define CONFIG_CONS_INDEX              1       /* UART0 */
>  #endif


Amicalement,
-- 
Albert.