[U-Boot] [PATCH v2 1/5] mvtwsi: convert to CONFIG_SYS_I2C framework
Hans de Goede
hdegoede at redhat.com
Fri Jun 13 22:55:48 CEST 2014
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
Acked-by: Heiko Schocher <hs at denx.de>
---
arch/arm/include/asm/arch-kirkwood/config.h | 3 +-
drivers/i2c/Makefile | 2 +-
drivers/i2c/mvtwsi.c | 70 +++++++++++++----------------
include/configs/edminiv2.h | 3 +-
4 files changed, 37 insertions(+), 41 deletions(-)
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
index 7a688e4..f7bfa0e 100644
--- a/arch/arm/include/asm/arch-kirkwood/config.h
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -129,7 +129,8 @@
*/
#ifdef CONFIG_CMD_I2C
#ifndef CONFIG_SYS_I2C_SOFT
-#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
#endif
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index e33586d..61e9f3c 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -7,7 +7,6 @@
obj-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o
obj-$(CONFIG_DW_I2C) += designware_i2c.o
-obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
obj-$(CONFIG_I2C_MV) += mv_i2c.o
obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
@@ -19,6 +18,7 @@ obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o
obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o
obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o
+obj-$(CONFIG_SYS_I2C_MVTWSI) += mvtwsi.o
obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
index 5ba0e03..c8b5425 100644
--- a/drivers/i2c/mvtwsi.c
+++ b/drivers/i2c/mvtwsi.c
@@ -220,11 +220,10 @@ static int twsi_stop(int status)
/*
* Reset controller.
- * Called at end of i2c_init unsuccessful i2c transactions.
* Controller reset also resets the baud rate and slave address, so
- * re-establish them.
+ * they must be re-established afterwards.
*/
-static void twsi_reset(u8 baud_rate, u8 slave_address)
+static void twsi_reset(struct i2c_adapter *adap)
{
/* ensure controller will be enabled by any twsi*() function */
twsi_control_flags = MVTWSI_CONTROL_TWSIEN;
@@ -232,23 +231,17 @@ static void twsi_reset(u8 baud_rate, u8 slave_address)
writel(0, &twsi->soft_reset);
/* wait 2 ms -- this is what the Marvell LSP does */
udelay(20000);
- /* set baud rate */
- writel(baud_rate, &twsi->baudrate);
- /* set slave address even though we don't use it */
- writel(slave_address, &twsi->slave_address);
- writel(0, &twsi->xtnd_slave_addr);
- /* assert STOP but don't care for the result */
- (void) twsi_stop(0);
}
/*
* I2C init called by cmd_i2c when doing 'i2c reset'.
* Sets baud to the highest possible value not exceeding requested one.
*/
-void i2c_init(int requested_speed, int slaveadd)
+static unsigned int twsi_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int requested_speed)
{
- int tmp_speed, highest_speed, n, m;
- int baud = 0x44; /* baudrate at controller reset */
+ unsigned int tmp_speed, highest_speed, n, m;
+ unsigned int baud = 0x44; /* baudrate at controller reset */
/* use actual speed to collect progressively higher values */
highest_speed = 0;
@@ -263,8 +256,21 @@ void i2c_init(int requested_speed, int slaveadd)
}
}
}
+ writel(baud, &twsi->baudrate);
+ return 0;
+}
+
+static void twsi_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
+{
/* reset controller */
- twsi_reset(baud, slaveadd);
+ twsi_reset(adap);
+ /* set speed */
+ twsi_i2c_set_bus_speed(adap, speed);
+ /* set slave address even though we don't use it */
+ writel(slaveadd, &twsi->slave_address);
+ writel(0, &twsi->xtnd_slave_addr);
+ /* assert STOP but don't care for the result */
+ (void) twsi_stop(0);
}
/*
@@ -294,7 +300,7 @@ static int i2c_begin(int expected_start_status, u8 addr)
* I2C probe called by cmd_i2c when doing 'i2c probe'.
* Begin read, nak data byte, end.
*/
-int i2c_probe(uchar chip)
+static int twsi_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
u8 dummy_byte;
int status;
@@ -320,12 +326,13 @@ int i2c_probe(uchar chip)
* cmd_eeprom, so we have to choose here, and for the moment that'll be
* a repeated start without a preceding stop.
*/
-int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *data, int length)
{
int status;
/* begin i2c write to send the address bytes */
- status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+ status = i2c_begin(MVTWSI_STATUS_START, (chip << 1));
/* send addr bytes */
while ((status == 0) && alen--)
status = twsi_send(addr >> (8*alen),
@@ -333,7 +340,7 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
/* begin i2c read to receive eeprom data bytes */
if (status == 0)
status = i2c_begin(
- MVTWSI_STATUS_REPEATED_START, (dev << 1) | 1);
+ MVTWSI_STATUS_REPEATED_START, (chip << 1) | 1);
/* prepare ACK if at least one byte must be received */
if (length > 0)
twsi_control_flags |= MVTWSI_CONTROL_ACK;
@@ -355,12 +362,13 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
* I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
* Begin write, send address byte(s), send data bytes, end.
*/
-int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int twsi_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *data, int length)
{
int status;
/* begin i2c write to send the eeprom adress bytes then data bytes */
- status = i2c_begin(MVTWSI_STATUS_START, (dev << 1));
+ status = i2c_begin(MVTWSI_STATUS_START, (chip << 1));
/* send addr bytes */
while ((status == 0) && alen--)
status = twsi_send(addr >> (8*alen),
@@ -374,21 +382,7 @@ int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
return status;
}
-/*
- * Bus set routine: we only support bus 0.
- */
-int i2c_set_bus_num(unsigned int bus)
-{
- if (bus > 0) {
- return -1;
- }
- return 0;
-}
-
-/*
- * Bus get routine: hard-return bus 0.
- */
-unsigned int i2c_get_bus_num(void)
-{
- return 0;
-}
+U_BOOT_I2C_ADAP_COMPLETE(twsi0, twsi_i2c_init, twsi_i2c_probe,
+ twsi_i2c_read, twsi_i2c_write,
+ twsi_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 0)
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 8b9f66a..77717a8 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -187,7 +187,8 @@
* I2C related stuff
*/
#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE ORION5X_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
--
2.0.0
More information about the U-Boot
mailing list