[U-Boot] [PATCH 1/6] usb: ehci: mx6: Add support for i.MX6SL

[Stefano Babic]

Hi Otavio,

On 16/06/2014 02:46, Otavio Salvador wrote:
> The i.MX6SL has a different base address for the controller. This
> patch adapts the driver to support the different base address for this
> case.
> 
> Signed-off-by: Otavio Salvador <otavio at ossystems.com.br>
> ---
> 
>  drivers/usb/host/ehci-mx6.c | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
> index c0a557b..5ba1c5e 100644
> --- a/drivers/usb/host/ehci-mx6.c
> +++ b/drivers/usb/host/ehci-mx6.c
> @@ -53,6 +53,12 @@
>  #define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
>  #define UCMD_RESET		(1 << 1) /* controller reset */
>  
> +#ifdef CONFIG_MX6SL
> +#define USB_BASE_ADDR		USBO2H_USB_BASE_ADDR
> +#else
> +#define USB_BASE_ADDR		USBOH3_USB_BASE_ADDR
> +#endif
> +

What about using the is_cpu_type() function, recently added together
with SPL support ? I think we have reached, thank to Tim's patches, the
goal to have a single image for different Freescale's mx6 variations. It
is pity to go back and decide at compile time which SOC is running.

>  static const unsigned phy_bases[] = {
>  	USB_PHY0_BASE_ADDR,
>  	USB_PHY1_BASE_ADDR,
> @@ -174,7 +180,7 @@ struct usbnc_regs {
>  
>  static void usb_oc_config(int index)
>  {
> -	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USBOH3_USB_BASE_ADDR +
> +	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
>  			USB_OTHERREGS_OFFSET);
>  	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
>  	u32 val;
> @@ -207,7 +213,7 @@ int ehci_hcd_init(int index, enum usb_init_type init,
>  		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
>  {
>  	enum usb_init_type type;
> -	struct usb_ehci *ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
> +	struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
>  		(0x200 * index));
>  
>  	if (index > 3)
> 

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================