[U-Boot] [Patch v9 5/5] ARMv8/ls2085a_emu: Add LS2085A emulator and simulator board support
York Sun
yorksun at freescale.com
Tue Jun 24 00:15:56 CEST 2014
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Arnab Basu <arnab.basu at freescale.com>
Signed-off-by: J. German Rivera <German.Rivera at freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
---
Change log
v9: no change
v8: Rename ls2100a to ls2085a according to latest SoC name.
Add "support for GIC 500" in commit message.
v7: no change
v6: no change
v5: no change
v4: no change
v3: Add support for DDR4 target and simulator target
Squash Manage complex patch (previous 5/5) into this
Reserve last 512MB memory for MC use
Change MC firmware location in NOR flash
Fix UART clock source speed
Update IFC address mux
Use generic board
Disable DDR memory beyound 39 physical address space due to Linux limitation
arch/arm/cpu/armv8/fsl-lsch3/README | 2 +-
arch/arm/include/asm/arch-fsl-lsch3/config.h | 2 +-
board/freescale/ls2085a/Makefile | 8 +
board/freescale/ls2085a/README | 16 ++
board/freescale/{t4rdb => ls2085a}/ddr.c | 89 ++++++++--
board/freescale/ls2085a/ddr.h | 57 +++++++
board/freescale/ls2085a/ls2085a.c | 100 ++++++++++++
boards.cfg | 3 +
include/configs/ls2085a_common.h | 226 ++++++++++++++++++++++++++
include/configs/ls2085a_emu.h | 19 +++
include/configs/ls2085a_simu.h | 16 ++
11 files changed, 520 insertions(+), 18 deletions(-)
create mode 100644 board/freescale/ls2085a/Makefile
create mode 100644 board/freescale/ls2085a/README
copy board/freescale/{t4rdb => ls2085a}/ddr.c (53%)
create mode 100644 board/freescale/ls2085a/ddr.h
create mode 100644 board/freescale/ls2085a/ls2085a.c
create mode 100644 include/configs/ls2085a_common.h
create mode 100644 include/configs/ls2085a_emu.h
create mode 100644 include/configs/ls2085a_simu.h
diff --git a/arch/arm/cpu/armv8/fsl-lsch3/README b/arch/arm/cpu/armv8/fsl-lsch3/README
index de34a91..cc47466 100644
--- a/arch/arm/cpu/armv8/fsl-lsch3/README
+++ b/arch/arm/cpu/armv8/fsl-lsch3/README
@@ -7,4 +7,4 @@
Freescale LayerScape with Chassis Generation 3
This architecture supports Freescale ARMv8 SoCs with Chassis generation 3,
-for example LS2100A.
+for example LS2085A.
diff --git a/arch/arm/include/asm/arch-fsl-lsch3/config.h b/arch/arm/include/asm/arch-fsl-lsch3/config.h
index c987a19..c1c718e 100644
--- a/arch/arm/include/asm/arch-fsl-lsch3/config.h
+++ b/arch/arm/include/asm/arch-fsl-lsch3/config.h
@@ -53,7 +53,7 @@
/* IFC */
#define CONFIG_SYS_FSL_IFC_LE
-#ifdef CONFIG_LS2100A
+#ifdef CONFIG_LS2085A
#define CONFIG_MAX_CPUS 16
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
#define CONFIG_NUM_DDR_CONTROLLERS 2
diff --git a/board/freescale/ls2085a/Makefile b/board/freescale/ls2085a/Makefile
new file mode 100644
index 0000000..701b35c
--- /dev/null
+++ b/board/freescale/ls2085a/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2014 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += ls2085a.o
+obj-y += ddr.o
diff --git a/board/freescale/ls2085a/README b/board/freescale/ls2085a/README
new file mode 100644
index 0000000..b7023e1
--- /dev/null
+++ b/board/freescale/ls2085a/README
@@ -0,0 +1,16 @@
+Freescale ls2085a_emu
+
+This is a emulator target with limited peripherals.
+
+Memory map from core's view
+
+0x00_0000_0000 .. 0x00_000F_FFFF Boot Rom
+0x00_0100_0000 .. 0x00_0FFF_FFFF CCSR
+0x00_1800_0000 .. 0x00_181F_FFFF OCRAM
+0x00_3000_0000 .. 0x00_3FFF_FFFF IFC region #1
+0x00_8000_0000 .. 0x00_FFFF_FFFF DDR region #1
+0x05_1000_0000 .. 0x05_FFFF_FFFF IFC region #2
+0x80_8000_0000 .. 0xFF_FFFF_FFFF DDR region #2
+
+Other addresses are either reserved, or not used directly by u-boot.
+This list should be updated when more addresses are used.
diff --git a/board/freescale/t4rdb/ddr.c b/board/freescale/ls2085a/ddr.c
similarity index 53%
copy from board/freescale/t4rdb/ddr.c
copy to board/freescale/ls2085a/ddr.c
index 5a43c1b..257bc16 100644
--- a/board/freescale/t4rdb/ddr.c
+++ b/board/freescale/ls2085a/ddr.c
@@ -5,12 +5,8 @@
*/
#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <asm/mmu.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
-#include <asm/fsl_law.h>
#include "ddr.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -22,7 +18,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
- if (ctrl_num > 2) {
+ if (ctrl_num > 3) {
printf("Not supported controller number %d\n", ctrl_num);
return;
}
@@ -39,7 +35,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
pbsp = udimms[0];
- /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
@@ -59,8 +55,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
}
if (pbsp_highest) {
- printf("Error: board specific timing not found for data\n"
- "rate %lu MT/s\n"
+ printf("Error: board specific timing not found for data rate %lu MT/s\n"
"Trying to use the highest speed (%u) parameters\n",
ddr_freq, pbsp_highest->datarate_mhz_high);
popts->clk_adjust = pbsp_highest->clk_adjust;
@@ -72,8 +67,7 @@ void fsl_ddr_board_options(memctl_options_t *popts,
}
found:
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
- "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n"
- "wrlvl_ctrl_3 0x%x\n",
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
@@ -82,7 +76,7 @@ found:
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
- popts->half_strength_driver_enable = 0;
+ popts->half_strength_driver_enable = 1;
/*
* Write leveling override
*/
@@ -97,22 +91,85 @@ found:
/* Enable ZQ calibration */
popts->zq_en = 1;
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
/* DHC_EN =1, ODT = 75 Ohm */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
}
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 2,
+ .rank_density = 1073741824u,
+ .capacity = 2147483648,
+ .primary_sdram_width = 64,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 14,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 937,
+ .caslat_x = 0x6FC << 4, /* 14,13,11,10,9,8,7,6 */
+ .taa_ps = 13090,
+ .twr_ps = 15000,
+ .trcd_ps = 13090,
+ .trrd_ps = 5000,
+ .trp_ps = 13090,
+ .tras_ps = 33000,
+ .trc_ps = 46090,
+ .trfc_ps = 160000,
+ .twtr_ps = 7500,
+ .trtp_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tfaw_ps = 25000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if (((controller_number == 0) && (dimm_number == 0)) ||
+ ((controller_number == 1) && (dimm_number == 0))) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+#endif
phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
- puts("Initializing....using SPD\n");
+ puts("Initializing DDR....");
+ puts("using SPD\n");
dram_size = fsl_ddr_sdram();
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-
- puts(" DDR: ");
return dram_size;
}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
+ gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+ gd->bd->bi_dram[1].size = gd->ram_size -
+ CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ } else {
+ gd->bd->bi_dram[0].size = gd->ram_size;
+ }
+}
diff --git a/board/freescale/ls2085a/ddr.h b/board/freescale/ls2085a/ddr.h
new file mode 100644
index 0000000..77f6aaf
--- /dev/null
+++ b/board/freescale/ls2085a/ddr.h
@@ -0,0 +1,57 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {2, 2140, 0, 4, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {4, 2140, 0, 5, 4, 0x0, 0x0},
+ {2, 2140, 0, 5, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+};
+
+
+#endif
diff --git a/board/freescale/ls2085a/ls2085a.c b/board/freescale/ls2085a/ls2085a.c
new file mode 100644
index 0000000..a18db1d
--- /dev/null
+++ b/board/freescale/ls2085a/ls2085a.c
@@ -0,0 +1,100 @@
+/*
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <netdev.h>
+#include <fsl_ifc.h>
+#include <fsl_ddr.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <libfdt.h>
+#include <fsl_mc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ init_final_memctl_regs();
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ init_early_memctl_regs(); /* tighten IFC timing */
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ printf("DRAM: ");
+ gd->ram_size = initdram(0);
+
+ return 0;
+}
+
+int timer_init(void)
+{
+ u32 __iomem *cntcr = (u32 *)CONFIG_SYS_FSL_TIMER_ADDR;
+ u32 __iomem *cltbenr = (u32 *)CONFIG_SYS_FSL_PMU_CLTBENR;
+
+ out_le32(cltbenr, 0x1); /* enable cluster0 timebase */
+ out_le32(cntcr, 0x1); /* enable clock for timer */
+
+ return 0;
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int error = 0;
+
+#ifdef CONFIG_SMC91111
+ error = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+ error = cpu_eth_init(bis);
+#endif
+ return error;
+}
+
+#ifdef CONFIG_FSL_MC_ENET
+void fdt_fixup_board_enet(void *fdt)
+{
+ int offset;
+
+ offset = fdt_path_offset(fdt, "/fsl,dprc at 0");
+ if (get_mc_boot_status() == 0)
+ fdt_status_okay(fdt, offset);
+ else
+ fdt_status_fail(fdt, offset);
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ /* limit the memory size to bank 1 until Linux can handle 40-bit PA */
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_FSL_MC_ENET
+ fdt_fixup_board_enet(blob);
+#endif
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 947f2bc..1ceacc2 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -44,6 +44,9 @@
###########################################################################################################
Active aarch64 armv8 - armltd vexpress64 vexpress_aemv8a vexpress_aemv8a:ARM64 David Feng <fenghua at phytium.com.cn>
+Active aarch64 armv8 fsl-lsch3 freescale ls2085a ls2085a_emu ls2085a_emu:ARM64,EMU York Sun <yorksun at freescale.com>
+Active aarch64 armv8 fsl-lsch3 freescale ls2085a ls2085a_emu_D4 ls2085a_emu:ARM64,EMU,SYS_FSL_DDR4 York Sun <yorksun at freescale.com>
+Active aarch64 armv8 fsl-lsch3 freescale ls2085a ls2085a_simu ls2085a_simu:ARM64,SIMU York Sun <yorksun at freescale.com>
Active arc arc700 - synopsys - axs101 - Alexey Brodkin <abrodkin at synopsys.com>
Active arc arc700 - synopsys <none> arcangel4 - Alexey Brodkin <abrodkin at synopsys.com>
Active arc arc700 - synopsys <none> arcangel4-be - Alexey Brodkin <abrodkin at synopsys.com>
diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2085a_common.h
new file mode 100644
index 0000000..2bd5a47
--- /dev/null
+++ b/include/configs/ls2085a_common.h
@@ -0,0 +1,226 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS2_COMMON_H
+#define __LS2_COMMON_H
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LSCH3
+#define CONFIG_LS2085A
+#define CONFIG_GICV3
+
+/* Link Definitions */
+#define CONFIG_SYS_TEXT_BASE 0x30000000
+
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+#define CONFIG_IDENT_STRING " LS2085A-EMU"
+#define CONFIG_BOOTP_VCI_STRING "U-boot.LS2085A-EMU"
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#ifndef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
+#define CONFIG_SYS_DDR_RAW_TIMING
+#endif
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+
+#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
+
+/* SMP Definitions */
+#define CPU_RELEASE_ADDR CONFIG_SYS_INIT_SP_ADDR
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 12000000 /* 12MHz */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_MXC_I2C1_SPEED 40000000
+#define CONFIG_SYS_MXC_I2C2_SPEED 40000000
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/* IFC */
+#define CONFIG_FSL_IFC
+#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/*
+ * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
+ * address 0. But this region is limited to 256MB. To accommodate bigger NOR
+ * flash and other devices, we will map CS0 to 0x580000000 after relocation.
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
+#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+
+/*
+ * NOR Flash Timing Params
+ */
+#define CONFIG_SYS_NOR0_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
+ FTIM0_NOR_TEADC(0x1) | \
+ FTIM0_NOR_TEAHC(0x1))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \
+ FTIM1_NOR_TRAD_NOR(0x1))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) | \
+ FTIM2_NOR_TCH(0x0) | \
+ FTIM2_NOR_TWP(0x1))
+#define CONFIG_SYS_NOR_FTIM3 0x04000000
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+/* MC firmware */
+#define CONFIG_FSL_MC_ENET
+#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
+#define CONFIG_SYS_LS_MC_FW_IN_NOR
+#define CONFIG_SYS_LS_MC_FW_ADDR 0x580200000ULL
+/* TODO Actual FW length needs to be determined at runtime from FW header */
+#define CONFIG_SYS_LS_MC_FW_LENGTH (4U * 1024 * 1024)
+#define CONFIG_SYS_LS_MC_DPL_IN_NOR
+#define CONFIG_SYS_LS_MC_DPL_ADDR 0x5806C0000ULL
+/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
+#define CONFIG_SYS_LS_MC_DPL_LENGTH 4096
+#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0xe00000
+
+/* Carve the MC private DRAM block from the end of DRAM */
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_SYS_MEM_TOP_HIDE mc_get_dram_block_size()
+#endif
+
+/* Command line configuration */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+
+/* Physical Memory Map */
+/* fixme: these need to be checked against the board */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#define CONFIG_SYS_CLK_FREQ 133333333
+
+
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE 128
+
+#define CONFIG_DISPLAY_CPUINFO
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x80100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x581200000\0" \
+ "kernel_load=0x806f0000\0" \
+ "kernel_size=0x1000000\0" \
+ "console=ttyAMA0,38400n8\0"
+
+#define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \
+ "earlyprintk=uart8250-8bit,0x21c0600"
+#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
+ "$kernel_size && bootm $kernel_load"
+#define CONFIG_BOOTDELAY 1
+
+/* Store environment at top of flash */
+#define CONFIG_ENV_IS_NOWHERE 1
+#define CONFIG_ENV_SIZE 0x1000
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PROMPT "> "
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#ifndef __ASSEMBLY__
+unsigned long mc_get_dram_block_size(void);
+#endif
+
+#endif /* __LS2_COMMON_H */
diff --git a/include/configs/ls2085a_emu.h b/include/configs/ls2085a_emu.h
new file mode 100644
index 0000000..a5cea63
--- /dev/null
+++ b/include/configs/ls2085a_emu.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS2_EMU_H
+#define __LS2_EMU_H
+
+#include "ls2085a_common.h"
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR_EMU /* Support emulator */
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD on I2C bus 1 */
+
+#endif /* __LS2_EMU_H */
diff --git a/include/configs/ls2085a_simu.h b/include/configs/ls2085a_simu.h
new file mode 100644
index 0000000..46d47b0
--- /dev/null
+++ b/include/configs/ls2085a_simu.h
@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS2_SIMU_H
+#define __LS2_SIMU_H
+
+#include "ls2085a_common.h"
+
+/* SMSC 91C111 ethernet configuration */
+#define CONFIG_SMC91111
+#define CONFIG_SMC91111_BASE (0x2210000)
+
+#endif /* __LS2_SIMU_H */
--
1.7.9.5
More information about the U-Boot
mailing list