[U-Boot] [PATCH v3 11/11] odroid: add odroid_config

Przemyslaw Marczak p.marczak at samsung.com
Thu Jun 26 16:15:37 CEST 2014


This config is valid for two devices:
- Odroid X2,
- Odroid U3.

Signed-off-by: Przemyslaw Marczak <p.marczak at samsung.com>
Cc: Minkyu Kang <mk7.kang at samsung.com>
Cc: Tom Rini <trini at ti.com>

---
Changes v2:
- odroid config: add CONFIG_DFU_ALT_BOOTLOADER
- odroid config: change name of CONFIG_DFU_BOOT_ALT_* to CONFIG_DFU_ALT_BOOT_*

Changes v3:
- odroid.h: update CONFIG_DFU_ALT_BOOT_** with required bootloader binaries
- odroid.h: add multi image support (CONFIG_FIT)
- odroid.h: add "autoboot" script for multi boot options
- odroid.h: change env name: dfu_alt_info -> dfu_alt_system
- odroid.h: update config name: CONFIG_SET_DFU_ALT_INFO
- odroid.h: reduce boot delay to 0 seconds
- update: doc/README.odroid
---
 boards.cfg               |   1 +
 doc/README.odroid        | 144 +++++++++++++++++++++++++++++
 include/configs/odroid.h | 232 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 377 insertions(+)
 create mode 100644 doc/README.odroid
 create mode 100644 include/configs/odroid.h

diff --git a/boards.cfg b/boards.cfg
index 1527ebe..8e8bcb3 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -297,6 +297,7 @@ Active  arm         armv7          exynos      samsung         smdk5420
 Active  arm         armv7          exynos      samsung         smdkv310            smdkv310                              -                                                                                                                                 Chander Kashyap <k.chander at samsung.com>
 Active  arm         armv7          exynos      samsung         trats               trats                                 -                                                                                                                                 Lukasz Majewski <l.majewski at samsung.com>
 Active  arm         armv7          exynos      samsung         trats2              trats2                                -                                                                                                                                 Piotr Wilczek <p.wilczek at samsung.com>
+Active  arm         armv7          exynos      samsung         odroid              odroid                                -                                                                                                                                 Przemyslaw Marczak <p.marczak at samsung.com>
 Active  arm         armv7          exynos      samsung         universal_c210      s5pc210_universal                     -                                                                                                                                 Przemyslaw Marczak <p.marczak at samsung.com>
 Active  arm         armv7          highbank    -               highbank            highbank                              -                                                                                                                                 Rob Herring <robh at kernel.org>
 Active  arm         armv7          keystone    ti              k2hk_evm            k2hk_evm                              -                                                                                                                                 Vitaly Andrianov <vitalya at ti.com>
diff --git a/doc/README.odroid b/doc/README.odroid
new file mode 100644
index 0000000..15aba10
--- /dev/null
+++ b/doc/README.odroid
@@ -0,0 +1,144 @@
+ U-boot for Odroid X2/U3
+========================
+
+1. Summary
+==========
+This is a quick instruction for setup Odroid boards based on Exynos4412.
+Board config: odroid_config
+
+2. Supported devices
+====================
+This U-BOOT config can be used on two boards:
+- Odroid U3
+- Odroid X2
+with CPU Exynos 4412 rev 2.0 and 2GB of RAM
+
+3. Boot sequence
+================
+iROM->BL1->(BL2 + TrustZone)->U-BOOT
+
+This version of U-BOOT doesn't implement SPL but it is required(BL2)
+and can be found in "boot.tar.gz" from here:
+http://dev.odroid.com/projects/4412boot/wiki/FrontPage?action=download&value=boot.tar.gz
+
+4. Boot media layout
+====================
+The table below shows SD/eMMC cards layout for U-boot.
+The block offset is starting from 0 and the block size is 512B.
+ -------------------------------------
+|  Binary   | Block offset| part type |
+|   name    | SD   | eMMC |(eMMC only)|
+ -------------------------------------
+| Bl1       | 1    | 0    |  1 (boot) |
+| Bl2       | 31   | 30   |  1 (boot) |
+| U-boot    | 63   | 62   |  1 (boot) |
+| Tzsw      | 2111 | 2110 |  1 (boot) |
+| Uboot Env | 2500 | 2500 |  0 (user) |
+ -------------------------------------
+
+5. Prepare the SD boot card - with SD card reader
+=================================================
+To prepare bootable media you need boot binaries provided by hardkernel.
+File "boot.tar.gz" (link in point 3.) contains:
+- E4412_S.bl1.HardKernel.bin
+- E4412_S.tzsw.signed.bin
+- bl2.signed.bin
+- sd_fusing.sh
+- u-boot.bin
+
+This is all you need to boot this board. But if you want to use your custom
+u-boot then you need to change u-boot.bin with your own u-boot binary*
+and run the script "sd_fusing.sh" - this script is valid only for SD card.
+
+*note:
+The proper binary file of current U-boot is u-boot-dtb.bin.
+
+quick steps for Linux:
+- extract boot.tar.gz
+- put any SD card into the SD reader
+- check the device with "dmesg"
+- run ./sd_fusing.sh /dev/sdX - where X is SD card device (but not a partition)
+Check if Hardkernel U-boot is booting, and next do the same with your U-boot.
+
+6. Prepare the eMMC boot card
+   with a eMMC card reader (boot from eMMC card slot)
+=====================================================
+To boot the device from the eMMC slot you should use a special card reader
+which supports eMMC partiion switch. All of the boot binaries are stored
+on the eMMC boot partition which is normally hidden.
+
+The "sd_fusing.sh" script can be used after updating offsets of binaries
+according to the table from point 4. Be sure that you are working on the right
+eMMC partition - its size is usually very small, about 1-4 MiB.
+
+7. Prepare the eMMC boot card
+   with a SD card reader (boot from SD card slot)
+=================================================
+If you have an eMMC->microSD adapter you can prepare the card as in point 5.
+But then the device can boot only from the SD card slot.
+
+8. Prepare the boot media using Hardkernel U-boot
+=================================================
+You can update the U-boot to the custom one if you have an working bootloader
+delivered with the board on a eMMC/SD card. Then follow the steps:
+- install the android fastboot tool
+- connect a micro usb cable to the board
+- on the U-boot prompt, run command: fastboot (as a root)
+- on the host, run command: "fastboot flash bootloader u-boot-dtb.bin"
+- the custom U-boot should start after the board resets.
+
+9. Partition layout
+====================
+Default U-boot environment is setup for fixed partiion layout.
+
+Partition table: MSDOS. Disk layout and files as listed in the table below.
+ ----- ------ ------ ------ -------- ---------------------------------
+| Num | Name |  FS  | Size | Offset |         Reguired files          |
+|     |      | Type |  MiB |  MiB   |                                 |
+ ----- ------ ------ ------ -------- ---------------------------------
+|  1  | BOOT | fat  |  100 |   2    | uImage, exynos4412-odroid**.dtb |
+|  2  | ROOT | ext4 | 3072 |        |  any Linux system               |
+|  3  | DATA | any  | 3072 |        |                                 |
+|  4  | UMS  | any  | any  |        |                                 |
+ ----- ------ ------ ------ -------- ---------------------------------
+
+**note:
+Supported fdt files are:
+- exynos4412-odroidx2.dtb
+- exynos4412-odroidu3.dtb
+
+Supported kernel files are:
+- Image.itb
+- zImage
+- uImage
+
+The default environmental variable "dfu_alt_info" is set* for above layout.
+Each partition size is just an example, dfu_alt_info tries init four partitions.
+The size of each is not important.
+
+*note:
+$dfu_alt_info is set on a boot time and it is concatenated using two variables:
+- $dfu_alt_boot(set dynamically)
+- $dfu_alt_system(from current env).
+
+To add any changes to dfu_alt_info - please modify $dfu_alt_system only.
+Changes are visible after board reset.
+
+10. The environment and booting the kernel
+==========================================
+There are three macros defined in config for various boot options:
+Two for both, kernel with device tree support and also without it:
+- boot_uimg - load uImage
+- boot_zimg - load zImage
+The device tree support can be enabled by setting the env variable:
+- "setenv kernel_usefdt 1" (enabled by default)
+- "setenv kernel_usefdt 0" (for old kernel types)
+
+The third boot option for multi image support (more info: doc/uImage.FIT/)
+- boot_fit - for binary file: "Image.itb"
+
+Default boot command: "autoboot"
+And the boot sequence is:
+- boot_fit - if "Image.itb" exists
+- boot_zimg - if "zImage" exists
+- boot_uimg - if "uImage" exists
diff --git a/include/configs/odroid.h b/include/configs/odroid.h
new file mode 100644
index 0000000..4a4f171
--- /dev/null
+++ b/include/configs/odroid.h
@@ -0,0 +1,232 @@
+/*
+ * Copyright (C) 2014 Samsung Electronics
+ * Sanghee Kim <sh0130.kim at samsung.com>
+ * Piotr Wilczek <p.wilczek at samsung.com>
+ * Przemyslaw Marczak <p.marczak at samsung.com>
+ *
+ * Configuation settings for the Odroid-U3 (EXYNOS4412) board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_ODROID_U3_H
+#define __CONFIG_ODROID_U3_H
+
+#include <configs/exynos4-dt.h>
+
+#define CONFIG_SYS_PROMPT	"Odroid # "	/* Monitor Command Prompt */
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE	exynos4412-odroid
+
+#define CONFIG_SYS_L2CACHE_OFF
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define CONFIG_SYS_L2_PL310
+#define CONFIG_SYS_PL310_BASE	0x10502000
+#endif
+
+#define CONFIG_MACH_TYPE	4289
+
+#define CONFIG_NR_DRAM_BANKS	8
+#define CONFIG_SYS_SDRAM_BASE	0x40000000
+#define SDRAM_BANK_SIZE		(256 << 20)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
+
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+#define CONFIG_SYS_TEXT_BASE		0x43e00000
+
+#include <linux/sizes.h>
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (80 * SZ_1M))
+
+/* select serial console configuration */
+#define CONFIG_SERIAL1
+#define CONFIG_BAUDRATE			115200
+
+/* Console configuration */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE
+#define CONFIG_BOOTARGS			"Please use defined boot"
+#define CONFIG_BOOTCOMMAND		"run autoboot"
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
+
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR \
+					- GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_MEM_TOP_HIDE	(SZ_1M)	/* ram console */
+
+#define CONFIG_SYS_MONITOR_BASE	0x00000000
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		CONFIG_MMC_DEFAULT_DEV
+#define CONFIG_ENV_SIZE			4096
+#define CONFIG_ENV_OFFSET		(SZ_1K * 1280) /* 1.25 MiB offset */
+#define CONFIG_ENV_OVERWRITE
+
+/* Partitions name */
+#define PARTS_BOOT		"boot"
+#define PARTS_ROOT		"platform"
+#define PARTS_DATA		"data"
+#define PARTS_UMS		"ums"
+
+#define CONFIG_DFU_ALT \
+	"uImage fat 0 1;" \
+	"zImage fat 0 1;" \
+	"Image.itb fat 0 1;" \
+	"exynos4412-odroidu3.dtb fat 0 1;" \
+	"exynos4412-odroidx2.dtb fat 0 1;" \
+	""PARTS_BOOT" part 0 1;" \
+	""PARTS_ROOT" part 0 2;" \
+	""PARTS_DATA" part 0 3;" \
+	""PARTS_UMS" part 0 4\0"
+
+#define CONFIG_SET_DFU_ALT_INFO
+
+#define CONFIG_DFU_ALT_BOOT_EMMC \
+	"u-boot raw 0x3e 0x800 mmcpart 1;" \
+	"bl1 raw 0x0 0x1e mmcpart 1;" \
+	"bl2 raw 0x1e 0x1d mmcpart 1;" \
+	"tzsw raw 0x83e 0x138 mmcpart 1\0"
+
+#define CONFIG_DFU_ALT_BOOT_SD \
+	"u-boot raw 0x3f 0x800;" \
+	"bl1 raw 0x1 0x1e;" \
+	"bl2 raw 0x1f 0x1d;" \
+	"tzsw raw 0x83f 0x138\0"
+
+/*
+ * Bootable media layout:
+ * dev:    SD   eMMC(part boot)
+ * BL1      1    0
+ * BL2     31   30
+ * UBOOT   63   62
+ * TZSW  2111 2110
+ * ENV   2560 2560(part user)
+ *
+ * MBR Primary partiions:
+ * Num Name   Size  Offset
+ * 1.  BOOT:  100MiB 2MiB
+ * 2.  ROOT:  3GiB
+ * 3.  DATA:  3GiB
+ * 4.  UMS:   -
+*/
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadkernel=fatload mmc ${mmcbootdev}:${mmcbootpart} ${kerneladdr} " \
+		"${kernelname}\0" \
+	"loaddtb=fatload mmc ${mmcbootdev}:${mmcbootpart} ${fdtaddr} "\
+		"${fdtfile}\0" \
+	"kernel_args=" \
+		"setenv bootargs root=/dev/mmcblk${mmcrootdev}p${mmcrootpart} "\
+		"${rootopts} ${lpj} ${console} ${meminfo} ${opts} ${lcdinfo}\0"\
+	"boot_fit=" \
+		"setenv kerneladdr 0x42000000;" \
+		"setenv kernelname Image.itb;" \
+		"run loadkernel;" \
+		"run kernel_args;" \
+		"bootm ${kerneladdr}#${boardname}\0" \
+	"boot_uimg=" \
+		"setenv kerneladdr 0x40007FC0;" \
+		"setenv kernelname uImage;" \
+		"run loadkernel;" \
+		"run kernel_args;" \
+		"if test $kernel_usefdt = 1; then " \
+			"if run loaddtb; then " \
+				"bootm ${kerneladdr} - ${fdtaddr};" \
+			"fi;" \
+		"fi;" \
+		"bootm ${kerneladdr};\0" \
+	"boot_zimg=" \
+		"setenv kerneladdr 0x40007FC0;" \
+		"setenv kernelname zImage;" \
+		"run loadkernel;" \
+		"run kernel_args;" \
+		"if test $kernel_usefdt = 1; then " \
+			"if run loaddtb; then " \
+				"bootz ${kerneladdr} - ${fdtaddr};" \
+			"fi;" \
+		"fi;" \
+		"bootz ${kerneladdr};\0" \
+	"autoboot=" \
+		"if test -e mmc 0 Image.itb; then; " \
+			"run boot_fit;" \
+		"elif test -e mmc 0 zImage; then; " \
+			"run boot_zimg;" \
+		"elif test -e mmc 0 uImage; then; " \
+			"run boot_uimg;" \
+		"fi;\0" \
+	"bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \
+	"boottrace=setenv opts initcall_debug; run bootcmd\0" \
+	"console=" CONFIG_DEFAULT_CONSOLE \
+	"kernelname=uImage\0" \
+	"kernel_usefdt=1\0" \
+	"mmcbootdev=0\0" \
+	"mmcbootpart=1\0" \
+	"mmcrootdev=0\0" \
+	"mmcrootpart=2\0" \
+	"bootdelay=0\0" \
+	"boardname=\0" \
+	"rootopts=rootwait\0" \
+	"opts=always_resume=1\0" \
+	"dfu_alt_system="CONFIG_DFU_ALT \
+	"dfu_alt_info=Please reset the board\0" \
+	"consoleon=set console console=ttySAC1,115200n8; save; reset\0" \
+	"consoleoff=set console console=ram; save; reset\0" \
+	"fdtaddr=40800000\0"
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_S3C24X0
+#define CONFIG_SYS_I2C_S3C24X0_SPEED	100000
+#define CONFIG_SYS_I2C_S3C24X0_SLAVE	0
+#define CONFIG_MAX_I2C_NUM		8
+#define CONFIG_SYS_I2C_INIT_BOARD
+
+/* POWER */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_MAX77686
+
+/* GPT */
+#define CONFIG_RANDOM_UUID
+
+/* Security subsystem - enable hw_rand() */
+#define CONFIG_EXYNOS_ACE_SHA
+#define CONFIG_LIB_HW_RAND
+
+#define CONFIG_CMD_GPIO
+
+/*
+ * Supported Odroid boards: X3, U3
+ * TODO: Add Odroid X support
+ */
+#define CONFIG_MISC_COMMON
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+#define CONFIG_BOARD_TYPES
+#define CONFIG_MISC_INIT_R
+
+#undef CONFIG_REVISION_TAG
+
+#endif	/* __CONFIG_H */
-- 
1.9.1



More information about the U-Boot mailing list