[U-Boot] [PATCH v2] powerpc/t2080rdb: Add T2080PCIe-RDB board support
Shengzhou Liu
Shengzhou.Liu at freescale.com
Tue Mar 4 06:36:00 CET 2014
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.
T2080PCIe-RDB Feature Overview
------------------------------
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
- SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
- SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
- NOR: 128MB 16-bit NOR flash
- NAND: 512MB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 gold-finger
- One PCIe x4 connector
- One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a TF-card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu at freescale.com>
---
v2: update readme.
board/freescale/t208xrdb/Makefile | 13 +
board/freescale/t208xrdb/README | 208 +++++++++
board/freescale/t208xrdb/cpld.c | 71 +++
board/freescale/t208xrdb/cpld.h | 42 ++
board/freescale/t208xrdb/ddr.c | 112 +++++
board/freescale/t208xrdb/ddr.h | 47 ++
board/freescale/t208xrdb/eth_t208xrdb.c | 106 +++++
board/freescale/t208xrdb/law.c | 34 ++
board/freescale/t208xrdb/pci.c | 23 +
board/freescale/t208xrdb/t2080_pbi.cfg | 41 ++
board/freescale/t208xrdb/t2080_rcw.cfg | 8 +
board/freescale/t208xrdb/t208xrdb.c | 124 +++++
board/freescale/t208xrdb/t208xrdb.h | 13 +
board/freescale/t208xrdb/tlb.c | 151 +++++++
boards.cfg | 5 +
include/configs/T208xRDB.h | 779 ++++++++++++++++++++++++++++++++
16 files changed, 1777 insertions(+)
create mode 100644 board/freescale/t208xrdb/Makefile
create mode 100644 board/freescale/t208xrdb/README
create mode 100644 board/freescale/t208xrdb/cpld.c
create mode 100644 board/freescale/t208xrdb/cpld.h
create mode 100644 board/freescale/t208xrdb/ddr.c
create mode 100644 board/freescale/t208xrdb/ddr.h
create mode 100644 board/freescale/t208xrdb/eth_t208xrdb.c
create mode 100644 board/freescale/t208xrdb/law.c
create mode 100644 board/freescale/t208xrdb/pci.c
create mode 100644 board/freescale/t208xrdb/t2080_pbi.cfg
create mode 100644 board/freescale/t208xrdb/t2080_rcw.cfg
create mode 100644 board/freescale/t208xrdb/t208xrdb.c
create mode 100644 board/freescale/t208xrdb/t208xrdb.h
create mode 100644 board/freescale/t208xrdb/tlb.c
create mode 100644 include/configs/T208xRDB.h
diff --git a/board/freescale/t208xrdb/Makefile b/board/freescale/t208xrdb/Makefile
new file mode 100644
index 0000000..092c9ff
--- /dev/null
+++ b/board/freescale/t208xrdb/Makefile
@@ -0,0 +1,13 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_T2080RDB) += t208xrdb.o
+obj-$(CONFIG_T2080RDB) += eth_t208xrdb.o
+obj-$(CONFIG_T2080RDB) += cpld.o
+obj-$(CONFIG_PCI) += pci.o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
new file mode 100644
index 0000000..0012c6c
--- /dev/null
+++ b/board/freescale/t208xrdb/README
@@ -0,0 +1,208 @@
+T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
+It can work in two mode: standalone mode and PCIe endpoint mode.
+
+T2080 SoC Overview
+------------------
+The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
+Architecture processor cores with high-performance datapath acceleration
+logic and network and peripheral bus interfaces required for networking,
+telecom/datacom, wireless infrastructure, and mil/aerospace applications.
+
+T2080 includes the following functions and features:
+ - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
+ - 2MB L2 cache and 512KB CoreNet platform cache (CPC)
+ - Hierarchical interconnect fabric
+ - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
+ - Data Path Acceleration Architecture (DPAA) incorporating acceleration
+ - 16 SerDes lanes up to 10.3125 GHz
+ - 8 Ethernet interfaces, supporting combinations of the following:
+ - Up to four 10 Gbps Ethernet MACs
+ - Up to eight 1 Gbps Ethernet MACs
+ - Up to four 2.5 Gbps Ethernet MACs
+ - High-speed peripheral interfaces
+ - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
+ - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
+ - Additional peripheral interfaces
+ - Two serial ATA (SATA 2.0) controllers
+ - Two high-speed USB 2.0 controllers with integrated PHY
+ - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
+ - Enhanced serial peripheral interface (eSPI)
+ - Four I2C controllers
+ - Four 2-pin UARTs or two 4-pin UARTs
+ - Integrated Flash Controller supporting NAND and NOR flash
+ - Three eight-channel DMA engines
+ - Support for hardware virtualization and partitioning enforcement
+ - QorIQ Platform's Trust Architecture 2.0
+
+Differences between T2080 and T2081
+-----------------------------------
+ Feature T2080 T2081
+ 1G Ethernet numbers: 8 6
+ 10G Ethernet numbers: 4 2
+ SerDes lanes: 16 8
+ Serial RapidIO,RMan: 2 no
+ SATA Controller: 2 no
+ Aurora: yes no
+ SoC Package: 896-pins 780-pins
+
+
+T2080PCIe-RDB board Overview
+----------------------------
+ - SERDES Configuration
+ - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
+ - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
+ - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
+ - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
+ - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
+ - SerDes-2 Lane G-H: to SATA1 & SATA2
+ - Ethernet
+ - Two on-board 10M/100M/1G RGMII ethernet ports
+ - Two on-board 10Gbps XFI fiber ports
+ - Two on-board 10Gbps Base-T copper ports
+ - DDR Memory
+ - Supports 72bit 4GB DDR3-LP SODIMM
+ - PCIe
+ - One PCIe x4 gold-finger
+ - One PCIe x4 connector
+ - One PCIe x2 end-point device (C293 Crypto co-processor)
+ - IFC/Local Bus
+ - NOR: 128MB 16-bit NOR Flash
+ - NAND: 512MB 8-bit NAND flash
+ - CPLD: for system controlling with programable header on-board
+ - SATA
+ - Two SATA 2.0 onnectors on-board
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V at 1.5A per port.
+ - SDHC
+ - one TF-card connector on-board
+ - SPI
+ - On-board 64MB SPI flash
+ - Other
+ - Two Serial ports
+ - Four I2C ports
+
+
+System Memory map
+-----------------
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB
+0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB
+0x0_0000_0000 0x0_ffff_ffff DDR 4GB
+
+
+128M NOR Flash memory Map
+-------------------------
+Start Address End Address Definition Max size
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xEFE00000 0xEFE3FFFF PHY CS4315 firmware 256KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+T2080PCIe-RDB Ethernet Port Map
+-------------------------------
+Label In Uboot In Linux FMan Address Comments PHY
+ETH0 FM1 at GTEC1 fm1-mac9 0xfe4f0000 10G SFP+ (CS4315)
+ETH1 FM1 at GTEC2 fm1-mac10 0xfe4f2000 10G SFP+ (CS4315)
+ETH2 FM1 at GTEC3 fm1-mac1 0xfe4e0000 10G Base-T (AQ1202)
+ETH3 FM1 at GTEC4 fm1-mac2 0xfe4e2000 10G Base-T (AQ1202)
+ETH4 FM1 at DTSEC3 fm1-mac3 0xfe4e4000 1G RGMII (RTL8211E)
+ETH5 FM1 at DTSEC4 fm1-mac4 0xfe4e6000 1G RGMII (RTL8211E)
+
+
+T2080PCIe-RDB Default DIP-Switch setting
+----------------------------------------
+SW1[1:8] = '00010011'
+SW2[1:8] = '10111111'
+SW3[1:8] = '11100001'
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+ a. build NOR boot image
+ $ make T2080RDB
+ b. program u-boot.bin image to NOR flash
+ => tftp 1000000 u-boot.bin
+ => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+ set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+
+ Switching between default bank and alternate bank on NOR flash
+ To change boot source to vbank4:
+ via software: run command 'cpld reset altbank' in u-boot.
+ via DIP-switch: set SW3[5:7] = '011'
+
+ To change boot source to vbank0:
+ via software: run command 'cpld reset' in u-boot.
+ via DIP-Switch: set SW3[5:7] = '111'
+
+2. NAND Boot:
+ a. build PBL image for NAND boot
+ $ make T2080RDB_NAND_config
+ $ make u-boot.pbl
+ b. program u-boot.pbl to NAND flash
+ => tftp 1000000 u-boot.pbl
+ => nand erase 0 d0000
+ => nand write 1000000 0 $filesize
+ set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
+
+3. SPI Boot:
+ a. build PBL image for SPI boot
+ $ make T2080RDB_SPIFLASH_config
+ $ make u-boot.pbl
+ b. program u-boot.pbl to SPI flash
+ => tftp 1000000 u-boot.pbl
+ => sf probe 0
+ => sf erase 0 d0000
+ => sf write 1000000 0 $filesize
+ set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+ a. build PBL image for SD boot
+ $ make T2080RDB_SDCARD_config
+ $ make u-boot.pbl
+ b. program u-boot.pbl to TF card
+ => tftp 1000000 u-boot.pbl
+ => mmc write 1000000 8 1650
+ set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+How to update the ucode of Cortina CS4315/CS4340 10G PHY
+--------------------------------------------------------
+=> tftp 1000000 CS4315-CS4340-PHY-ucode.txt
+=> pro off all;era 0xefe00000 0xefefffff;cp.b 1000000 0xefe00000 $filesize
+
+
+How to update the ucode of Freescale FMAN
+-----------------------------------------
+=> tftp 1000000 fsl_fman_ucode_t2080_r1.0.bin
+=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize
+
+
+For more details, please refer to T2080PCIe-RDB User Guide and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t208xrdb/cpld.c b/board/freescale/t208xrdb/cpld.c
new file mode 100644
index 0000000..4aa126b
--- /dev/null
+++ b/board/freescale/t208xrdb/cpld.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Freescale T2080RDB board-specific CPLD controlling supports.
+ */
+
+#include <common.h>
+#include <command.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/* Set the boot bank to the alternate bank */
+void cpld_set_altbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET);
+}
+
+/* Set the boot bank to the default bank */
+void cpld_set_defbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET);
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_set_defbank();
+ } else {
+ rc = cmd_usage(cmdtp);
+ }
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset: reset to default bank\n"
+ "cpld reset altbank: reset to alternate bank\n"
+);
diff --git a/board/freescale/t208xrdb/cpld.h b/board/freescale/t208xrdb/cpld.h
new file mode 100644
index 0000000..4cee4e5
--- /dev/null
+++ b/board/freescale/t208xrdb/cpld.h
@@ -0,0 +1,42 @@
+/*
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * CPLD register set of T2080RDB board-specific.
+ */
+struct cpld_data {
+ u8 chip_id1; /* 0x00 - Chip ID1 register */
+ u8 chip_id2; /* 0x01 - Chip ID2 register */
+ u8 hw_ver; /* 0x02 - Hardware Revision Register */
+ u8 sw_ver; /* 0x03 - Software Revision register */
+ u8 res0[12]; /* 0x04 - 0x0F - not used */
+ u8 reset_ctl; /* 0x10 - Reset control Register */
+ u8 flash_csr; /* 0x11 - Flash control and status register */
+ u8 thermal_csr; /* 0x12 - Thermal control and status register */
+ u8 led_csr; /* 0x13 - LED control and status register */
+ u8 sfp_csr; /* 0x14 - SFP+ control and status register */
+ u8 misc_csr; /* 0x15 - Misc control and status register */
+ u8 boot_or; /* 0x16 - Boot config override register */
+ u8 boot_cfg1; /* 0x17 - Boot configuration register 1 */
+ u8 boot_cfg2; /* 0x18 - Boot configuration register 2 */
+} cpld_data_t;
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value) \
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_LBMAP_MASK 0x3F
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_OVERRIDE 0x40
+#define CPLD_LBMAP_ALTBANK 0x43 /* BANK OR | BANK 4 */
+#define CPLD_LBMAP_DFLTBANK 0x47 /* BANK OR | BANK 0 */
+#define CPLD_LBMAP_RESET 0xFF
+#define CPLD_LBMAP_SHIFT 0x03
+#define CPLD_BOOT_SEL 0x80
diff --git a/board/freescale/t208xrdb/ddr.c b/board/freescale/t208xrdb/ddr.c
new file mode 100644
index 0000000..01e9173
--- /dev/null
+++ b/board/freescale/t208xrdb/ddr.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or later as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
+ "wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ puts(" DDR: ");
+ return dram_size;
+}
diff --git a/board/freescale/t208xrdb/ddr.h b/board/freescale/t208xrdb/ddr.h
new file mode 100644
index 0000000..b6d4062
--- /dev/null
+++ b/board/freescale/t208xrdb/ddr.h
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
+ */
+ {2, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a},
+ {2, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09},
+ {2, 1600, 2, 5, 8, 0x0808070b, 0x0c0d0e0a},
+ {2, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a},
+ {2, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c},
+ {1, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a},
+ {1, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09},
+ {1, 1600, 2, 5, 8, 0x0808070b, 0x0c0d0e0a},
+ {1, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a},
+ {1, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+#endif
diff --git a/board/freescale/t208xrdb/eth_t208xrdb.c b/board/freescale/t208xrdb/eth_t208xrdb.c
new file mode 100644
index 0000000..ab4c0cd
--- /dev/null
+++ b/board/freescale/t208xrdb/eth_t208xrdb.c
@@ -0,0 +1,106 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu at freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ struct mii_dev *dev;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+
+ switch (srds_s1) {
+ case 0x66:
+ case 0x6b:
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_10GEC3, FM1_10GEC3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_10GEC4, FM1_10GEC4_PHY_ADDR);
+ break;
+ default:
+ printf("SerDes1 protocol 0x%x is not supported on T208xRDB\n",
+ srds_s1);
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+ return;
+}
diff --git a/board/freescale/t208xrdb/law.c b/board/freescale/t208xrdb/law.c
new file mode 100644
index 0000000..eb82431
--- /dev/null
+++ b/board/freescale/t208xrdb/law.c
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ /* Limit DCSR to 32M to access NPC Trace Buffer */
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t208xrdb/pci.c b/board/freescale/t208xrdb/pci.c
new file mode 100644
index 0000000..ba7041a
--- /dev/null
+++ b/board/freescale/t208xrdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2007-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t208xrdb/t2080_pbi.cfg b/board/freescale/t208xrdb/t2080_pbi.cfg
new file mode 100644
index 0000000..e200d92
--- /dev/null
+++ b/board/freescale/t208xrdb/t2080_pbi.cfg
@@ -0,0 +1,41 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Refer doc/README.pblimage for more details about how-to configure
+# and create PBL boot image
+#
+
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#512KB SRAM
+09010100 00000000
+09010104 fff80009
+09010f00 08000000
+#enable CPC1
+09010000 80000000
+#Configure LAW for CPC1
+09000d00 00000000
+09000d04 fff80000
+09000d08 81000012
+#Initialize eSPI controller, default configuration is slow for eSPI to
+#load data, this configuration comes from u-boot eSPI driver.
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Errata for slowing down the MDC clock to make it <= 2.5 MHZ
+094fc030 00008148
+094fd030 00008148
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
diff --git a/board/freescale/t208xrdb/t2080_rcw.cfg b/board/freescale/t208xrdb/t2080_rcw.cfg
new file mode 100644
index 0000000..cd62cc8
--- /dev/null
+++ b/board/freescale/t208xrdb/t2080_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header for T2080RDB
+aa55aa55 010e0100
+#SerDes Protocol: 0x66_0x16
+#Core/DDR: 1533Mhz/1600MT/s
+120c0017 15000000 00000000 00000000
+66160002 00008400 ec104000 c1000000
+00000000 00000000 00000000 000307fc
+00000000 00000000 00000000 00000004
diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c
new file mode 100644
index 0000000..f3fec2a
--- /dev/null
+++ b/board/freescale/t208xrdb/t208xrdb.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright 2009-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include "t208xrdb.h"
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
+
+ printf("Board: %sRDB, ", cpu->name);
+ printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
+ CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+
+#ifdef CONFIG_SDCARD
+ puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+ puts("SPI\n");
+#else
+ u8 reg;
+
+ reg = CPLD_READ(flash_csr);
+
+ if (reg & CPLD_BOOT_SEL) {
+ puts("NAND\n");
+ } else {
+ reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
+ printf("NOR vBank%d\n", ~reg & 0x7);
+ }
+#endif
+
+ puts("SERDES Reference Clocks:\n");
+ printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
+ printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+}
diff --git a/board/freescale/t208xrdb/t208xrdb.h b/board/freescale/t208xrdb/t208xrdb.h
new file mode 100644
index 0000000..13380d0
--- /dev/null
+++ b/board/freescale/t208xrdb/t208xrdb.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t208xrdb/tlb.c b/board/freescale/t208xrdb/tlb.c
new file mode 100644
index 0000000..085d9f5
--- /dev/null
+++ b/board/freescale/t208xrdb/tlb.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the
+ * space is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 1, 0x80000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_512M, 1),
+
+ /* *I*G* - PCIe 2, 0xa0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 3, 0xb0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+
+ /* *I*G* - PCIe 4, 0xc0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_32M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ /*
+ * *I*G - NAND
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so we use entry 16 for nand.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 16, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 17, BOOKE_PAGESZ_4K, 1),
+#endif
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for
+ * fetching ucode and ENV from master
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 18, BOOKE_PAGESZ_1M, 1),
+#endif
+#if defined(CONFIG_SYS_RAMBOOT)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 19, BOOKE_PAGESZ_2G, 1)
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 3c3ebb8..bd00425 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -982,6 +982,11 @@ Active powerpc mpc85xx - freescale t208xqds
Active powerpc mpc85xx - freescale t208xqds T2081QDS_SPIFLASH T208xQDS:PPC_T2081,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t208xqds T2081QDS_NAND T208xQDS:PPC_T2081,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t208xqds T2081QDS_SRIO_PCIE_BOOT T208xQDS:PPC_T2081,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB T208xRDB:PPC_T2080
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SDCARD T208xRDB:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SPIFLASH T208xRDB:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_NAND T208xRDB:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000
+Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SRIO_PCIE_BOOT T208xRDB:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000
Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SPIFLASH T4240QDS:PPC_T4160,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
new file mode 100644
index 0000000..5d336e4
--- /dev/null
+++ b/include/configs/T208xRDB.h
@@ -0,0 +1,779 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * T2080 RDB/PCIe board configuration file
+ */
+
+#ifndef __T2080RDB_H
+#define __T2080RDB_H
+
+#define CONFIG_T2080RDB
+#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
+#define CONFIG_MMC
+#define CONFIG_SPI_FLASH
+#define CONFIG_USB_EHCI
+#define CONFIG_FSL_SATA_V2
+
+/* High Level Configuration Options */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MP /* support multiple processors */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xrdb/t2080_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xrdb/t2080_rcw.cfg
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1658)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 66660000
+#define CONFIG_DDR_CLK_FREQ 133330000
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+#define CTRL_INTLV_PREFERED cacheline
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe8000000
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS }
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE 0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT (0xf)
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2 0x0
+
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */\
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C3_SPEED 100000
+#define CONFIG_SYS_FSL_I2C4_SPEED 100000
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
+#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
+#define I2C_MUX_CH_DEFAULT 0x8
+
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+#endif
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE4 /* PCIE controler 4 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */
+#define CONFIG_NET_MULTI
+#define CONFIG_E1000
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 18
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 18
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN /* RMan */
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
+#define CONFIG_CORTINA_FW_ADDR 0x120000
+
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680)
+#define CONFIG_CORTINA_FW_ADDR (512 * 1808)
+
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_CORTINA_FW_ADDR (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
+#define CONFIG_CORTINA_FW_ADDR 0xFFE10000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000
+#define CONFIG_CORTINA_FW_ADDR 0xEFE00000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_CORTINA
+#define CONFIG_PHY_AQ1202
+#define CONFIG_PHY_REALTEK
+#define CONFIG_CORTINA_FW_LENGTH 0x40000
+#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
+#define RGMII_PHY2_ADDR 0x02
+#define FM1_10GEC1_PHY_ADDR 0x0c /* Cortina CS4315 */
+#define FM1_10GEC2_PHY_ADDR 0x0d
+#define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */
+#define FM1_10GEC4_PHY_ADDR 0x01
+#endif
+
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1 at DTSEC3"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Environment
+ */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define __USB_PHY_TYPE utmi
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t2080rdb/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t2080rdb/t2080rdb.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+#define CONFIG_PROOF_POINTS \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;" \
+ "cpu 2 release 0x29000000 - - -;" \
+ "cpu 3 release 0x29000000 - - -;" \
+ "cpu 4 release 0x29000000 - - -;" \
+ "cpu 5 release 0x29000000 - - -;" \
+ "cpu 6 release 0x29000000 - - -;" \
+ "cpu 7 release 0x29000000 - - -;" \
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;" \
+ "cpu 2 release 0x01000000 - - -;" \
+ "cpu 3 release 0x01000000 - - -;" \
+ "cpu 4 release 0x01000000 - - -;" \
+ "cpu 5 release 0x01000000 - - -;" \
+ "cpu 6 release 0x01000000 - - -;" \
+ "cpu 7 release 0x01000000 - - -;" \
+ "go 0x01000000"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#undef CONFIG_CMD_USB
+#endif
+
+#endif /* __T2080RDB_H */
--
1.8.0
More information about the U-Boot
mailing list