[U-Boot] [linux-sunxi] [PATCH v3 0/4] uboot sata support for sunxi platform

[Ezaul Zillmer]

Hi Ian


U-Boot SPL 2014.01-rc1-gb754a91 (Mar 12 2014 - 09:11:26)
Board: Cubieboard2
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.01-rc1-gb754a91 (Mar 12 2014 - 09:11:26) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: Cubieboard2
I2C:   ready
DRAM:  1 GiB
WARNING: Caches not enabled
MMC:   SUNXI SD/MMC: 0
SCSI:  SUNXI SCSI INIT
SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst 
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   mii0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0 
** Unrecognized filesystem type **
** File not found boot/uEnv.txt **
** File not found uEnv.txt **
** Unrecognized filesystem type **
414 bytes read in 11 ms (36.1 KiB/s)
Jumping to boot.scr
## Executing script at 44000000
45384 bytes read in 31 ms (1.4 MiB/s)
invalid extent block
invalid extent block
ext4fs_devread read outside partition 4294967120
20752 bytes read in 16 ms (1.2 MiB/s)
Wrong Image Format for bootm command
ERROR: can't get kernel image!
45384 bytes read in 18 ms (2.4 MiB/s)
invalid extent block
invalid extent block
ext4fs_devread read outside partition 4294967120
** Unrecognized filesystem type **
** File not found /script.bin **


 
What is not wrong that the boot SCSI wheel 
Where am I going wrong with leaving boot.cmd? 
use today as well 

boot.cmd 
setenv bootargs console = tty0 console = ttyS0, 115200 = hdmi.audio EDID: 0 
= disp.screen0_output_mode EDID: 1280x800p60 root = / dev/mmcblk0p1 
rootfstype = ext4 rootwait panic = 10 
ext4load mmc 0 0x43000000 boot / script.bin 
ext4load mmc 0 0x46000000 boot / uImage 
ext4load mmc 0 0x49000000 boot/cubie2.dtb 
env September fdt_high ffffffff 
bootm 0x46000000 - 0x49000000 

MMC for swap SCSI? 

It should be assimo Boot.cmd? 

setenv bootargs console = tty0 console = ttyS0, 115200 = hdmi.audio EDID: 0 
= disp.screen0_output_mode EDID: 1280x800p60 root = / dev/sda1 rootfstype = 
ext4 rootwait panic = 10 
ext4load 0 0x43000000 scsi boot / script.bin 
ext4load 0 0x46000000 scsi boot / uImage 
ext4load scsi 0 0x49000000 boot/cubie2.dtb 
env September fdt_high ffffffff 
bootm 0x46000000 - 0x49000000 

I thank 
Hug!




Em sábado, 8 de março de 2014 01h16min30s UTC-3, Ian Campbell escreveu:
>
> On Fri, 2014-03-07 at 08:44 -0800, Ezaul Zillmer wrote: 
> > You would have a repository with these updates where I could play with 
> > git, 
> > compile and test my cubieboard2 using kernel 3.14.rc5 
>
> git://gitorious.org/ijc/u-boot.git ahci-sunxi 
>
> It is based on jwrdegoede/sunxi-next. 
>
> Ian. 
>
>
>