[U-Boot] [PATCH 2/2] MarSBoard: add new board

Eric Bénard eric at eukrea.com
Wed Mar 26 19:26:03 CET 2014


this board is produced by Embest/Element 14 and is based on i.MX6 Dual
The following features are tested :
- UART2 (console)
- eMMC
- uSDCard
- Ethernet
- USB Host (through 2 ports hub)
- HDMI output
- I2C 1/2
- SPI NOR Flash

Boot on SPI NOR and through USB loader are tested.

For more informations on this board :
http://www.embest-tech.com/shop/star/marsboard.html

Signed-off-by: Eric Bénard <eric at eukrea.com>
---
 board/embest/marsboard/Makefile    |   9 +
 board/embest/marsboard/marsboard.c | 489 +++++++++++++++++++++++++++++++++++++
 boards.cfg                         |   1 +
 include/configs/marsboard.h        | 304 +++++++++++++++++++++++
 4 files changed, 803 insertions(+)
 create mode 100644 board/embest/marsboard/Makefile
 create mode 100644 board/embest/marsboard/marsboard.c
 create mode 100644 include/configs/marsboard.h

diff --git a/board/embest/marsboard/Makefile b/board/embest/marsboard/Makefile
new file mode 100644
index 0000000..e87cc87
--- /dev/null
+++ b/board/embest/marsboard/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := marsboard.o
diff --git a/board/embest/marsboard/marsboard.c b/board/embest/marsboard/marsboard.c
new file mode 100644
index 0000000..3735462
--- /dev/null
+++ b/board/embest/marsboard/marsboard.c
@@ -0,0 +1,489 @@
+/*
+ * Copyright (C) 2014 Eukréa Electromatique
+ * Author: Eric Bénard <eric at eukrea.com>
+ *         Fabio Estevam <fabio.estevam at freescale.com>
+ *         Jon Nettleton <jon.nettleton at gmail.com>
+ *
+ * based on sabresd.c which is :
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ * and on hummingboard.c which is :
+ * Copyright (C) 2013 SolidRun ltd.
+ * Copyright (C) 2013 Jon Nettleton <jon.nettleton at gmail.com>.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CLK_CTRL (PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST |			\
+	PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_PD  (PAD_CTL_PUS_100K_DOWN |		\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* GPIO16 -> AR8035 25MHz */
+	MX6_PAD_GPIO_16__ENET_REF_CLK	  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	/* AR8035 PHY Reset */
+	MX6_PAD_EIM_D31__GPIO3_IO31		| MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+	/* AR8035 PHY Interrupt */
+	MX6_PAD_ENET_TX_EN__GPIO1_IO28		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* Reset AR8035 PHY */
+	gpio_direction_output(IMX_GPIO_NR(3, 31) , 0);
+	mdelay(2);
+	gpio_set_value(IMX_GPIO_NR(3, 31), 1);
+}
+
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	/* from linux/arch/arm/mach-imx/mach-imx6q.c :
+	 * Ar803x phy SmartEEE feature cause link status generates glitch,
+	 * which cause ethernet link down/up issue, so disable SmartEEE
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_2__GPIO1_IO02	| MUX_PAD_CTRL(NO_PAD_CTRL), /* WP */
+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CLK_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_RST__GPIO7_IO08    | MUX_PAD_CTRL(NO_PAD_CTRL), /* eMMC RST */
+};
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC3_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC3 is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	s32 status = 0;
+	int i;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    uSDCard slot (bottom)
+	 * mmc1                    eMMC
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			usdhc_cfg[0].max_bus_width = 4;
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			usdhc_cfg[1].max_bus_width = 4;
+			gpio_direction_output(IMX_GPIO_NR(7, 8) , 0);
+			udelay(250);
+			gpio_set_value(IMX_GPIO_NR(7, 8), 1);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return status;
+		}
+
+		status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+	}
+
+	return status;
+}
+#endif
+
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+}
+
+struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+#if defined(CONFIG_VIDEO_IPUV3)
+struct display_info_t {
+	int	bus;
+	int	addr;
+	int	pixfmt;
+	int	(*detect)(struct display_info_t const *dev);
+	void	(*enable)(struct display_info_t const *dev);
+	struct	fb_videomode mode;
+};
+
+static int detect_hdmi(struct display_info_t const *dev)
+{
+	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+	return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT;
+}
+
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+static struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+
+int board_video_skip(void)
+{
+	int i;
+	int ret;
+	char const *panel = getenv("panel");
+	if (!panel) {
+		for (i = 0; i < ARRAY_SIZE(displays); i++) {
+			struct display_info_t const *dev = displays+i;
+			if (dev->detect && dev->detect(dev)) {
+				panel = dev->mode.name;
+				printf("auto-detected panel %s\n", panel);
+				break;
+			}
+		}
+		if (!panel) {
+			panel = displays[0].mode.name;
+			printf("No panel detected: default to %s\n", panel);
+			i = 0;
+		}
+	} else {
+		for (i = 0; i < ARRAY_SIZE(displays); i++) {
+			if (!strcmp(panel, displays[i].mode.name))
+				break;
+		}
+	}
+	if (i < ARRAY_SIZE(displays)) {
+		ret = ipuv3_fb_init(&displays[i].mode, 0,
+				    displays[i].pixfmt);
+		if (!ret) {
+			displays[i].enable(displays+i);
+			printf("Display: %s (%ux%u)\n",
+			       displays[i].mode.name,
+			       displays[i].mode.xres,
+			       displays[i].mode.yres);
+		} else
+			printf("LCD %s cannot be configured: %d\n",
+			       displays[i].mode.name, ret);
+	} else {
+		printf("unsupported panel %s\n", panel);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	/* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */
+	reg = readl(&mxc_ccm->CCGR3);
+	reg |=  MXC_CCM_CCGR3_LDB_DI0_MASK | MXC_CCM_CCGR3_LDB_DI1_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+
+	/* set LDB0, LDB1 clk select to 011/011 */
+	reg = readl(&mxc_ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+	      | (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	reg = readl(&mxc_ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV | MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV;
+	writel(reg, &mxc_ccm->cscmr2);
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	     | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW
+	     | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+	     | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
+	     | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
+	     | IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED
+	     | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK
+			| IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+
+	return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+#ifdef CONFIG_SYS_I2C
+	/* i2c1 : Expansion connector */
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	/* i2c2 : HDMI EDID */
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	/* i2c3 : LVDS, Expansion connector */
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+#endif
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	{"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: MarSBoard\n");
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index a29417c..06a32bc 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -324,6 +324,7 @@ Active  arm         armv7          mx6         freescale       mx6sabresd
 Active  arm         armv7          mx6         freescale       mx6slevk            mx6slevk                             mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL                                                                   Fabio Estevam <fabio.estevam at freescale.com>
 Active  arm         armv7          mx6         solidrun        hummingboard        hummingboard_solo                    hummingboard:IMX_CONFIG=board/solidrun/hummingboard/solo.cfg,MX6S,DDR_MB=512                                                      Jon Nettleton <jon.nettleton at gmail.com>
 Active  arm         armv7          mx6         embest          riotboard           riotboard                            riotboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024                                                 Eric Bénard <eric at eukrea.com>
+Active  arm         armv7          mx6         embest          marsboard           marsboard                            marsboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q.cfg,MX6Q,DDR_MB=1024                                                   Eric Bénard <eric at eukrea.com>
 Active  arm         armv7          omap3       -               overo               omap3_overo                          -                                                                                                                                 Steve Sakoman <sakoman at gmail.com>
 Active  arm         armv7          omap3       -               pandora             omap3_pandora                        -                                                                                                                                 Grazvydas Ignotas <notasas at gmail.com>
 Active  arm         armv7          omap3       8dtech          eco5pk              eco5pk                               -                                                                                                                                 Raphael Assenat <raph at 8d.com>
diff --git a/include/configs/marsboard.h b/include/configs/marsboard.h
new file mode 100644
index 0000000..ef7789a
--- /dev/null
+++ b/include/configs/marsboard.h
@@ -0,0 +1,304 @@
+/*
+ * Copyright (C) 2014 Eukréa Electromatique
+ * Author: Eric Bénard <eric at eukrea.com>
+ *
+ * Configuration settings for the Embest MarsBoard
+ *
+ * based on mx6*sabre*.h which are :
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MARSBOARD_CONFIG_H
+#define __MARSBOARD_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#include "mx6_common.h"
+#include <linux/sizes.h>
+
+#define CONFIG_MXC_UART_BASE		UART2_BASE
+#define CONFIG_CONSOLE_DEV		"ttymxc0"
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"
+#define CONFIG_DEFAULT_FDT_FILE	"imx6q-marsboard.dtb"
+#define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)
+
+#define CONFIG_MX6
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+
+#define CONFIG_CMD_FUSE
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		4
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+#define CONFIG_CMD_SF
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		(0 | (IMX_GPIO_NR(2, 30) << 8))
+#define CONFIG_SF_DEFAULT_SPEED		20000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#endif
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX              1
+#define CONFIG_BAUDRATE                        115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY               1
+
+#define CONFIG_LOADADDR                        0x12000000
+#define CONFIG_SYS_TEXT_BASE           0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x18000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"console=" CONFIG_CONSOLE_DEV "\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"initrd_high=0xffffffff\0" \
+	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
+	"mmcpart=1\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"update_spi_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if ${get_cmd} ${update_spi_firmware_filename}; then " \
+			"if sf probe; then "	\
+				"sf erase 0 0xc0000; " \
+				"sf write ${loadaddr} 0x400 ${filesize}; " \
+			"fi; "	\
+		"fi\0"	\
+	"update_sd_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if mmc dev ${mmcdev}; then "	\
+			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
+				"setexpr fw_sz ${filesize} / 0x200; " \
+				"setexpr fw_sz ${fw_sz} + 1; "	\
+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+			"fi; "	\
+		"fi\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc dev ${mmcdev};" \
+	"if mmc rescan; then " \
+		"if run loadbootscript; then " \
+		"run bootscript; " \
+		"else " \
+			"if run loadimage; then " \
+				"run mmcboot; " \
+			"else run netboot; " \
+			"fi; " \
+		"fi; " \
+	"else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT     200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE              256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START       0x10000000
+#define CONFIG_SYS_MEMTEST_END         0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE               (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE			(8 * 1024)
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET		(6 * 64 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV		1	/* SDHC3 */
+#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
+#define CONFIG_ENV_OFFSET		(768 * 1024)
+#define CONFIG_ENV_SECT_SIZE		(8 * 1024)
+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+#endif
+
+#define CONFIG_OF_LIBFDT
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
+
+#endif                         /* __MARSBOARD_CONFIG_H */
-- 
1.8.5.3



More information about the U-Boot mailing list