[U-Boot] [PATCH 09/10] exynos: Enable the LCD backlight for snow

[Ajay kumar]

Hi Simon,

Find my comments below:

On Wed, Mar 26, 2014 at 11:26 PM, Simon Glass <sjg at chromium.org> wrote:

> The backlight uses FETs on the TPS65090. Enable this so that the display
> is visible.
>
> Signed-off-by: Simon Glass <sjg at chromium.org>
> ---
>
>  board/samsung/smdk5250/exynos5-dt.c | 90
> +++++++++++++++++++++++++++++++++++++
>  1 file changed, 90 insertions(+)
>
> diff --git a/board/samsung/smdk5250/exynos5-dt.c
> b/board/samsung/smdk5250/exynos5-dt.c
> index c83b034..a0ae641 100644
> --- a/board/samsung/smdk5250/exynos5-dt.c
> +++ b/board/samsung/smdk5250/exynos5-dt.c
> @@ -20,6 +20,7 @@
>  #include <asm/arch/sromc.h>
>  #include <power/pmic.h>
>  #include <power/max77686_pmic.h>
> +#include <power/tps65090_pmic.h>
>  #include <tmu.h>
>
>  DECLARE_GLOBAL_DATA_PTR;
> @@ -60,6 +61,52 @@ int checkboard(void)
>  #endif
>
>  #ifdef CONFIG_LCD
>
We should make sure this code runs only for snow, and not for SMDK.
Only Snow contains the bridge chip.

> +static int board_dp_bridge_setup(void)
> +{
> +       struct exynos5_gpio_part1 *gpio1 =
> +               (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
> +       const int MAX_TRIES = 10;
> +       int num_tries;
> +
> +       debug("%s\n", __func__);
> +
> +       /* Setup the GPIOs */
> +
> +       /* PD is ACTIVE_LOW, and initially de-asserted */
> +       s5p_gpio_set_pull(&gpio1->y2, 5, GPIO_PULL_NONE);
> +       s5p_gpio_direction_output(&gpio1->y2, 5, 1);
> +
> +       /* Reset is ACTIVE_LOW */
> +       s5p_gpio_set_pull(&gpio1->x1, 5, GPIO_PULL_NONE);
> +       s5p_gpio_direction_output(&gpio1->x1, 5, 0);
> +
> +       udelay(10);
> +       s5p_gpio_set_value(&gpio1->x1, 5, 1);
> +
> +       s5p_gpio_direction_input(&gpio1->x0, 7);
> +
> +       /*
> +        * We need to wait for 90ms after bringing up the bridge since
> there
> +        * is a phantom "high" on the HPD chip during its bootup.  The
> phantom
> +        * high comes within 7ms of de-asserting PD and persists for at
> least
> +        * 15ms.  The real high comes roughly 50ms after PD is
> de-asserted. The
> +        * phantom high makes it hard for us to know when the NXP chip is
> up.
> +        */
> +       mdelay(90);
> +
> +       for (num_tries = 0; num_tries < MAX_TRIES; num_tries++) {
> +               /* Check HPD.  If it's high, we're all good. */
> +               if (s5p_gpio_get_value(&gpio1->x0, 7))
> +                               return 0;
> +
> +               debug("%s: eDP bridge failed to come up; try %d of %d\n",
> +                     __func__, num_tries, MAX_TRIES);
> +       }
> +
> +       /* Immediately go into bridge reset if the hp line is not high */
> +       return -ENODEV;
> +}
> +
>  void exynos_cfg_lcd_gpio(void)
>  {
>         struct exynos5_gpio_part1 *gpio1 =
> @@ -81,4 +128,47 @@ void exynos_set_dp_phy(unsigned int onoff)
>  {
>         set_dp_phy_ctrl(onoff);
>  }
> +
> +void exynos_backlight_on(unsigned int onoff)
> +{
> +       debug("%s(%u)\n", __func__, onoff);
> +
> +       if (onoff) {
> +#ifdef CONFIG_POWER_TPS65090
> +               struct exynos5_gpio_part1 *gpio1 =
> +                       (struct exynos5_gpio_part1 *)
> +                                       samsung_get_base_gpio_part1();
> +               int ret;
> +
> +               ret = tps65090_fet_enable(1); /* Enable FET1, backlight */
> +               if (ret)
> +                       return;
> +
> +               /* T5 in the LCD timing spec (defined as > 10ms) */
> +               mdelay(10);
>
Can you check for backlight without using the above delay?

> +
> +               /* board_dp_backlight_pwm */
> +               s5p_gpio_direction_output(&gpio1->b2, 0, 1);
>
+
> +               /* T6 in the LCD timing spec (defined as > 10ms) */
> +               mdelay(10);
>
Can you check for backlight without using the above delay?

> +
> +               /* board_dp_backlight_en */
> +               s5p_gpio_direction_output(&gpio1->x3, 0, 1);
> +#endif
> +       }
> +}
> +
> +void exynos_lcd_power_on(void)
> +{
> +       debug("%s\n", __func__);
> +
> +#ifdef CONFIG_POWER_TPS65090
> +       /* board_dp_lcd_vdd */
> +       tps65090_fet_enable(6); /* Enable FET6, lcd panel */
> +#endif
> +
> +       board_dp_bridge_setup();
>
returning int. check for return value and print in case of failure.

> +}
> +
>  #endif
> --
> 1.9.1.423.g4596e3a
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>


Regards,
Ajay Kumar