[U-Boot] [PATCH v6 16/17] video: dcu: Add Sii9022A HDMI Transmitter support

Alison Wang alison.wang at freescale.com
Fri Sep 5 07:44:12 CEST 2014


From: Wang Huan <b18965 at freescale.com>

On LS1021ATWR, Silicon's Sii9022A HDMI Transmitter
is used. This patch adds the common setting for this
chip.

Signed-off-by: Alison Wang <alison.wang at freescale.com>
---
Change log:
 v6: No change.
 v5: Change the patch order.
 v4: Add commit messages.
 v3: New file.

 board/freescale/common/Makefile       |   2 +
 board/freescale/common/dcu_sii9022a.c | 153 ++++++++++++++++++++++++++++++++++
 board/freescale/common/dcu_sii9022a.h |  13 +++
 3 files changed, 168 insertions(+)
 create mode 100644 board/freescale/common/dcu_sii9022a.c
 create mode 100644 board/freescale/common/dcu_sii9022a.h

diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 50d7731..32b5a3b 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -36,6 +36,8 @@ endif
 
 obj-$(CONFIG_FSL_DIU_CH7301)	+= diu_ch7301.o
 
+obj-$(CONFIG_FSL_DCU_SII9022A)    += dcu_sii9022a.o
+
 obj-$(CONFIG_MPC8541CDS)	+= cds_pci_ft.o
 obj-$(CONFIG_MPC8548CDS)	+= cds_pci_ft.o
 obj-$(CONFIG_MPC8555CDS)	+= cds_pci_ft.o
diff --git a/board/freescale/common/dcu_sii9022a.c b/board/freescale/common/dcu_sii9022a.c
new file mode 100644
index 0000000..2da627e
--- /dev/null
+++ b/board/freescale/common/dcu_sii9022a.c
@@ -0,0 +1,153 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_dcu_fb.h>
+#include <i2c.h>
+#include <linux/fb.h>
+
+#define PIXEL_CLK_LSB_REG		0x00
+#define PIXEL_CLK_MSB_REG		0x01
+#define VERT_FREQ_LSB_REG		0x02
+#define VERT_FREQ_MSB_REG		0x03
+#define TOTAL_PIXELS_LSB_REG		0x04
+#define TOTAL_PIXELS_MSB_REG		0x05
+#define TOTAL_LINES_LSB_REG		0x06
+#define TOTAL_LINES_MSB_REG		0x07
+#define TPI_INBUS_FMT_REG		0x08
+#define TPI_INPUT_FMT_REG		0x09
+#define TPI_OUTPUT_FMT_REG		0x0A
+#define TPI_SYS_CTRL_REG		0x1A
+#define TPI_PWR_STAT_REG		0x1E
+#define TPI_AUDIO_HANDING_REG		0x25
+#define TPI_AUDIO_INTF_REG		0x26
+#define TPI_AUDIO_FREQ_REG		0x27
+#define TPI_SET_PAGE_REG		0xBC
+#define TPI_SET_OFFSET_REG		0xBD
+#define TPI_RW_ACCESS_REG		0xBE
+#define TPI_TRANS_MODE_REG		0xC7
+
+#define TPI_INBUS_CLOCK_RATIO_1		(1 << 6)
+#define TPI_INBUS_FULL_PIXEL_WIDE	(1 << 5)
+#define TPI_INBUS_RISING_EDGE		(1 << 4)
+#define TPI_INPUT_CLR_DEPTH_8BIT	(0 << 6)
+#define TPI_INPUT_VRANGE_EXPAN_AUTO	(0 << 2)
+#define TPI_INPUT_CLR_RGB		(0 << 0)
+#define TPI_OUTPUT_CLR_DEPTH_8BIT	(0 << 6)
+#define TPI_OUTPUT_VRANGE_COMPRE_AUTO	(0 << 2)
+#define TPI_OUTPUT_CLR_HDMI_RGB		(0 << 0)
+#define TPI_SYS_TMDS_OUTPUT		(0 << 4)
+#define TPI_SYS_AV_NORAML		(0 << 3)
+#define TPI_SYS_AV_MUTE			(1 << 3)
+#define TPI_SYS_DVI_MODE		(0 << 0)
+#define TPI_SYS_HDMI_MODE		(1 << 0)
+#define TPI_PWR_STAT_MASK		(3 << 0)
+#define TPI_PWR_STAT_D0			(0 << 0)
+#define TPI_AUDIO_PASS_BASIC		(0 << 0)
+#define TPI_AUDIO_INTF_I2S		(2 << 6)
+#define TPI_AUDIO_INTF_NORMAL		(0 << 4)
+#define TPI_AUDIO_TYPE_PCM		(1 << 0)
+#define TPI_AUDIO_SAMP_SIZE_16BIT	(1 << 6)
+#define TPI_AUDIO_SAMP_FREQ_44K		(2 << 3)
+#define TPI_SET_PAGE_SII9022A		0x01
+#define TPI_SET_OFFSET_SII9022A		0x82
+#define TPI_RW_EN_SRC_TERMIN		(1 << 0)
+#define TPI_TRANS_MODE_ENABLE		(0 << 7)
+
+/* Programming of Silicon SIi9022a HDMI Transmitter */
+int dcu_set_dvi_encoder(struct fb_videomode *videomode)
+{
+	u8 temp;
+	u16 temp1, temp2;
+	u32 temp3;
+
+	i2c_set_bus_num(CONFIG_SYS_I2C_DVI_BUS_NUM);
+
+	/* Enable TPI transmitter mode */
+	temp = TPI_TRANS_MODE_ENABLE;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_TRANS_MODE_REG, 1, &temp, 1);
+
+	/* Enter into D0 state, full operation */
+	i2c_read(CONFIG_SYS_I2C_DVI_ADDR, TPI_PWR_STAT_REG, 1, &temp, 1);
+	temp &= ~TPI_PWR_STAT_MASK;
+	temp |= TPI_PWR_STAT_D0;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_PWR_STAT_REG, 1, &temp, 1);
+
+	/* Enable source termination */
+	temp = TPI_SET_PAGE_SII9022A;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_SET_PAGE_REG, 1, &temp, 1);
+	temp = TPI_SET_OFFSET_SII9022A;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_SET_OFFSET_REG, 1, &temp, 1);
+
+	i2c_read(CONFIG_SYS_I2C_DVI_ADDR, TPI_RW_ACCESS_REG, 1, &temp, 1);
+	temp |= TPI_RW_EN_SRC_TERMIN;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_RW_ACCESS_REG, 1, &temp, 1);
+
+	/* Set TPI system control */
+	temp = TPI_SYS_TMDS_OUTPUT | TPI_SYS_AV_NORAML | TPI_SYS_DVI_MODE;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_SYS_CTRL_REG, 1, &temp, 1);
+
+	/* Set pixel clock */
+	temp1 = PICOS2KHZ(videomode->pixclock) / 10;
+	temp = (u8)(temp1 & 0xFF);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, PIXEL_CLK_LSB_REG, 1, &temp, 1);
+	temp = (u8)(temp1 >> 8);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, PIXEL_CLK_MSB_REG, 1, &temp, 1);
+
+	/* Set total pixels per line */
+	temp1 = videomode->hsync_len + videomode->left_margin +
+		videomode->xres + videomode->right_margin;
+	temp = (u8)(temp1 & 0xFF);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TOTAL_PIXELS_LSB_REG, 1, &temp, 1);
+	temp = (u8)(temp1 >> 8);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TOTAL_PIXELS_MSB_REG, 1, &temp, 1);
+
+	/* Set total lines */
+	temp2 = videomode->vsync_len + videomode->upper_margin +
+		videomode->yres + videomode->lower_margin;
+	temp = (u8)(temp2 & 0xFF);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TOTAL_LINES_LSB_REG, 1, &temp, 1);
+	temp = (u8)(temp2 >> 8);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TOTAL_LINES_MSB_REG, 1, &temp, 1);
+
+	/* Set vertical frequency in Hz */
+	temp3 = temp1 * temp2;
+	temp3 = (PICOS2KHZ(videomode->pixclock) * 1000) / temp3;
+	temp1 = (u16)temp3 * 100;
+	temp = (u8)(temp1 & 0xFF);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, VERT_FREQ_LSB_REG, 1, &temp, 1);
+	temp = (u8)(temp1 >> 8);
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, VERT_FREQ_MSB_REG, 1, &temp, 1);
+
+	/* Set TPI input bus and pixel repetition data */
+	temp = TPI_INBUS_CLOCK_RATIO_1 | TPI_INBUS_FULL_PIXEL_WIDE |
+		TPI_INBUS_RISING_EDGE;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_INBUS_FMT_REG, 1, &temp, 1);
+
+	/* Set TPI AVI Input format data */
+	temp = TPI_INPUT_CLR_DEPTH_8BIT | TPI_INPUT_VRANGE_EXPAN_AUTO |
+		TPI_INPUT_CLR_RGB;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_INPUT_FMT_REG, 1, &temp, 1);
+
+	/* Set TPI AVI Output format data */
+	temp = TPI_OUTPUT_CLR_DEPTH_8BIT | TPI_OUTPUT_VRANGE_COMPRE_AUTO |
+		TPI_OUTPUT_CLR_HDMI_RGB;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_OUTPUT_FMT_REG, 1, &temp, 1);
+
+	/* Set TPI audio configuration write data */
+	temp = TPI_AUDIO_PASS_BASIC;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_AUDIO_HANDING_REG, 1, &temp, 1);
+
+	temp = TPI_AUDIO_INTF_I2S | TPI_AUDIO_INTF_NORMAL |
+		TPI_AUDIO_TYPE_PCM;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_AUDIO_INTF_REG, 1, &temp, 1);
+
+	temp = TPI_AUDIO_SAMP_SIZE_16BIT | TPI_AUDIO_SAMP_FREQ_44K;
+	i2c_write(CONFIG_SYS_I2C_DVI_ADDR, TPI_AUDIO_FREQ_REG, 1, &temp, 1);
+
+	return 0;
+}
diff --git a/board/freescale/common/dcu_sii9022a.h b/board/freescale/common/dcu_sii9022a.h
new file mode 100644
index 0000000..de76733
--- /dev/null
+++ b/board/freescale/common/dcu_sii9022a.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __DCU_HDMI_SII9022A__
+#define __DCU_HDMI_SII9022A__
+
+/* Programming of Silicon SII9022A connector HDMI Transmitter*/
+int dcu_set_dvi_encoder(struct fb_videomode *videomode);
+
+#endif
-- 
2.1.0.27.g96db324



More information about the U-Boot mailing list