[U-Boot] [PULL] Please pull u-boot-imx

Albert ARIBAUD albert.u.boot at aribaud.net
Tue Sep 16 16:38:59 CEST 2014


Hi Stefano,

On Fri, 12 Sep 2014 16:03:15 +0200, Stefano Babic <sbabic at denx.de>
wrote:

> Hi Albert,
> 
> please pull from u-boot-imx, thanks !
> 
> The board cm_fx6 cannot be built due to a couple of missing patches that
> are already merged into u-boot-spi. Please ignore this issue, the board
> will be compiled clean at the next iteration after Jagan's tree will be
> merged by Tom.
> 
> The following changes since commit a6bc0195dba895fa0e9facc718d17eb098695685:
> 
>   Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'
> (2014-09-09 09:19:10 +0200)
> 
> are available in the git repository at:
> 
> 
>   git://www.denx.de/git/u-boot-imx.git master
> 
> for you to fetch changes up to 4c97f16911e229f6d5bbea5bee52449916e5fa92:
> 
>   imx: mx6slevk: Change to use generic board (2014-09-11 11:04:26 +0200)
> 
> ----------------------------------------------------------------
> Fabio Estevam (9):
>       net: fec_mxc: Adjust RX DMA alignment for mx6solox
>       net: fec_mxc: Poll FEC_TBD_READY after polling TDAR
>       tools: imximage: Fix the maximum DCD size for mx53/mx6
>       mx6dlsabresd: Use its own DCD table
>       mx6qsabreauto: Remove imx6q-sabreauto.dts
>       mx6: imx-regs: Provide a structure for GPC registers
>       pcie_imx: Add mx6solox support
>       mx6sxsabresd: Add PCI support
>       README.imximage: Fix the maximum DCD size
> 
> Guillaume GARDET (1):
>       imx: nitrogen6x: Replace 'fatload' by 'load' command in env
> settings to be filesystem independent
> 
> Nikita Kiryanov (16):
>       mx6: add clock enabling functions
>       compulab: eeprom: add support for defining eeprom i2c bus

The commit above (52658fda7abc) breaks trimslice build (and later will
break cm_fx6 when it is introduced by 0991866cf7, or possibly before
that, at f66113c0ef) with the following errors :

| board/compulab/common/eeprom.c:37:24: error: 'CONFIG_SYS_I2C_EEPROM_BUS' undeclared (first use in this function) 

| board/compulab/common/eeprom.c:37:24: error: 'CONFIG_SYS_I2C_EEPROM_BUS' undeclared (first use in this function) 
| board/compulab/common/eeprom.c:37:24: note: each undeclared identifier is reported only once for each function it appears in 

(The repeat is certainly due to the same source file being built for SPL
then for U-Boot. Why the note is emitted only in one intance and not
the other is waaaaay beyond me.)

>       sata: dwc_ahsata: implement sata_port_status
>       i2c: imx: add macros to setup pads for multiple SoC types
>       arm: mx6: ddr: cleanup
>       arm: mx6: ddr: do not write into reserved bit
>       arm: mx6: ddr: configure MMDC for slow_pd
>       arm: mx6: ddr: fix cs0_end calculation
>       arm: mx6: add get_cpu_type()
>       arm: mx6: add support for Compulab cm-fx6 CoM
>       arm: mx6: cm_fx6: add nand support
>       arm: mx6: cm_fx6: add ethernet support
>       arm: mx6: cm_fx6: add usb support
>       arm: mx6: cm_fx6: add i2c support
>       arm: mx6: cm_fx6: use eeprom
>       arm: mx6: cm_fx6: add sata support
> 
> Nikolay Dimitrov (1):
>       mx6: Fix ECSPI typo in soc_boot_modes
> 
> Stefan Agner (2):
>       arm: vf610: lpuart: fix status register handling
>       arm: vf610: lpuart: disable FIFO on initializaton
> 
> Stefano Babic (1):
>       imx: Fix build of mx6sxsabresd
> 
> Thierry Reding (1):
>       imx: ventana: Avoid undefined behaviour
> 
> Tim Harvey (6):
>       imx: ventana: updated notes regarding NAND boot errata
>       imx: ventana: base SPL MMDC calibration on width and size not board
>       imx: ventana: add GW5520 support
>       imx: ventana: added cputype env var
>       pci: add support for board_pci_fixup_dev function
>       imx: ventana: add pci fixup for PLX PEX860x switch GPIO
> 
> Ye.Li (4):
>       iMX6: Disable the L2 before chaning the PL310 latency
>       imximage: Fix imximage IVT bug for EIM-NOR boot
>       imx: mx6q/dlarm2: Change to use generic board
>       imx: mx6slevk: Change to use generic board
> 
>  arch/arm/Kconfig                            |   4 +
>  arch/arm/cpu/armv7/mx6/clock.c              | 107 +++++-
>  arch/arm/cpu/armv7/mx6/ddr.c                | 277 ++++++++--------
>  arch/arm/cpu/armv7/mx6/soc.c                |  11 +-
>  arch/arm/dts/Makefile                       |   1 -
>  arch/arm/dts/imx6q-sabreauto.dts            |  13 -
>  arch/arm/include/asm/arch-mx6/clock.h       |   5 +
>  arch/arm/include/asm/arch-mx6/imx-regs.h    |  13 +
>  arch/arm/include/asm/arch-mx6/iomux.h       |   9 +
>  arch/arm/include/asm/arch-mx6/sys_proto.h   |   5 +-
>  arch/arm/include/asm/imx-common/mxc_i2c.h   |  33 ++
>  board/compulab/cm_fx6/Kconfig               |  23 ++
>  board/compulab/cm_fx6/MAINTAINERS           |   6 +
>  board/compulab/cm_fx6/Makefile              |  12 +
>  board/compulab/cm_fx6/cm_fx6.c              | 483
> ++++++++++++++++++++++++++++
>  board/compulab/cm_fx6/common.c              |  84 +++++
>  board/compulab/cm_fx6/common.h              |  37 +++
>  board/compulab/cm_fx6/imximage.cfg          |   8 +
>  board/compulab/cm_fx6/spl.c                 | 366 +++++++++++++++++++++
>  board/compulab/common/eeprom.c              |  13 +-
>  board/freescale/mx6sabresd/mx6dlsabresd.cfg | 131 ++++++++
>  board/gateworks/gw_ventana/eeprom.c         |   3 +
>  board/gateworks/gw_ventana/gsc.c            |   4 +
>  board/gateworks/gw_ventana/gw_ventana.c     | 118 ++++++-
>  board/gateworks/gw_ventana/gw_ventana_spl.c | 189 ++++++-----
>  board/gateworks/gw_ventana/ventana_eeprom.h |   1 +
>  configs/cm_fx6_defconfig                    |   4 +
>  configs/mx6dlsabresd_defconfig              |   2 +-
>  doc/README.imximage                         |   2 +-
>  drivers/block/dwc_ahsata.c                  |  17 +
>  drivers/net/fec_mxc.c                       |  42 ++-
>  drivers/pci/pci.c                           |   4 +
>  drivers/pci/pcie_imx.c                      |  40 ++-
>  drivers/serial/serial_lpuart.c              |  19 +-
>  include/configs/cm_fx6.h                    | 290 +++++++++++++++++
>  include/configs/cm_t335.h                   |   1 +
>  include/configs/cm_t35.h                    |   1 +
>  include/configs/cm_t54.h                    |   1 +
>  include/configs/gw_ventana.h                |   1 +
>  include/configs/mx6qarm2.h                  |   2 +
>  include/configs/mx6qsabreauto.h             |   3 -
>  include/configs/mx6slevk.h                  |   2 +
>  include/configs/mx6sxsabresd.h              |  10 +
>  include/configs/nitrogen6x.h                |   6 +-
>  include/pci.h                               |   7 +
>  include/sata.h                              |   1 +
>  tools/imximage.c                            |   7 +
>  tools/imximage.h                            |   2 +-
>  48 files changed, 2140 insertions(+), 280 deletions(-)
>  delete mode 100644 arch/arm/dts/imx6q-sabreauto.dts
>  create mode 100644 board/compulab/cm_fx6/Kconfig
>  create mode 100644 board/compulab/cm_fx6/MAINTAINERS
>  create mode 100644 board/compulab/cm_fx6/Makefile
>  create mode 100644 board/compulab/cm_fx6/cm_fx6.c
>  create mode 100644 board/compulab/cm_fx6/common.c
>  create mode 100644 board/compulab/cm_fx6/common.h
>  create mode 100644 board/compulab/cm_fx6/imximage.cfg
>  create mode 100644 board/compulab/cm_fx6/spl.c
>  create mode 100644 board/freescale/mx6sabresd/mx6dlsabresd.cfg
>  create mode 100644 configs/cm_fx6_defconfig
>  create mode 100644 include/configs/cm_fx6.h
> 
> Best regards,
> Stefano

Amicalement,
-- 
Albert.


More information about the U-Boot mailing list