[U-Boot] [PATCH v3 08/11] dm: imx: Use gpio_request() to request GPIOs

[Simon Glass]

GPIOs should be requested before use. Without this, driver model will not
permit the GPIO to be used.

Signed-off-by: Simon Glass <sjg at chromium.org>
---

Changes in v3:
- Add a check for the Ethernet gpio_request() also
- Add a comment for the CONFIG_SPL_BUILD #ifdef
- Just warn when one of the board init stages fails

Changes in v2:
- Check return values of gpio_request()

 arch/arm/imx-common/i2c-mxv7.c | 24 ++++++++++++++++++++++++
 board/compulab/cm_fx6/cm_fx6.c | 22 ++++++++++++++++++++--
 board/compulab/cm_fx6/common.c |  8 ++++++++
 3 files changed, 52 insertions(+), 2 deletions(-)

diff --git a/arch/arm/imx-common/i2c-mxv7.c b/arch/arm/imx-common/i2c-mxv7.c
index 70cff5c..aaf6936 100644
--- a/arch/arm/imx-common/i2c-mxv7.c
+++ b/arch/arm/imx-common/i2c-mxv7.c
@@ -4,6 +4,7 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #include <common.h>
+#include <malloc.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/errno.h>
@@ -72,10 +73,26 @@ static void * const i2c_bases[] = {
 int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
 	      struct i2c_pads_info *p)
 {
+	char *name1, *name2;
 	int ret;
 
 	if (i2c_index >= ARRAY_SIZE(i2c_bases))
 		return -EINVAL;
+
+	name1 = malloc(9);
+	name2 = malloc(9);
+	if (!name1 || !name2)
+		return -ENOMEM;
+	sprintf(name1, "i2c_sda%d", i2c_index);
+	sprintf(name2, "i2c_scl%d", i2c_index);
+	ret = gpio_request(p->sda.gp, name1);
+	if (ret)
+		goto err_req1;
+
+	ret = gpio_request(p->scl.gp, name2);
+	if (ret)
+		goto err_req2;
+
 	/* Enable i2c clock */
 	ret = enable_i2c_clk(1, i2c_index);
 	if (ret)
@@ -93,5 +110,12 @@ int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
 
 err_idle:
 err_clk:
+	gpio_free(p->scl.gp);
+err_req2:
+	gpio_free(p->sda.gp);
+err_req1:
+	free(name1);
+	free(name2);
+
 	return ret;
 }
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 10a568f..a089e82 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -71,8 +71,21 @@ static iomux_v3_cfg_t const sata_pads[] = {
 
 static int cm_fx6_setup_issd(void)
 {
+	int ret;
+	int i;
+
 	SETUP_IOMUX_PADS(sata_pads);
+
+	for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
+		ret = gpio_request(cm_fx6_issd_gpios[i], "sata");
+		if (ret)
+			return ret;
+	}
+
 	/* Make sure this gpio has logical 0 value */
+	ret = gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int");
+	if (ret)
+		return ret;
 	gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
 	udelay(100);
 
@@ -350,12 +363,17 @@ static int handle_mac_address(void)
 
 int board_eth_init(bd_t *bis)
 {
-	int res = handle_mac_address();
-	if (res)
+	int err;
+
+	err = handle_mac_address();
+	if (err)
 		puts("No MAC address found\n");
 
 	SETUP_IOMUX_PADS(enet_pads);
 	/* phy reset */
+	err = gpio_request(CM_FX6_ENET_NRST, "enet_nrst");
+	if (err)
+		printf("Etnernet NRST gpio request failed: %d\n", err);
 	gpio_direction_output(CM_FX6_ENET_NRST, 0);
 	udelay(500);
 	gpio_set_value(CM_FX6_ENET_NRST, 1);
diff --git a/board/compulab/cm_fx6/common.c b/board/compulab/cm_fx6/common.c
index 1f39679..20b758b 100644
--- a/board/compulab/cm_fx6/common.c
+++ b/board/compulab/cm_fx6/common.c
@@ -79,6 +79,14 @@ void cm_fx6_set_ecspi_iomux(void)
 
 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 {
+	/* DM does not support SPL yet and this function is not implemented */
+#ifndef CONFIG_SPL_BUILD
+	int ret;
+
+	ret = gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0");
+	if (ret)
+		return ret;
+#endif
 	return (bus == 0 && cs == 0) ? (CM_FX6_ECSPI_BUS0_CS0) : -1;
 }
 #endif
-- 
2.1.0.rc2.206.gedb03e5