[U-Boot] [PULL] Please pull u-boot-imx
Albert ARIBAUD
albert.u.boot at aribaud.net
Wed Sep 17 23:33:35 CEST 2014
Hi Stefano,
On Fri, 12 Sep 2014 16:03:15 +0200, Stefano Babic <sbabic at denx.de>
wrote:
> Hi Albert,
>
> please pull from u-boot-imx, thanks !
>
> The board cm_fx6 cannot be built due to a couple of missing patches that
> are already merged into u-boot-spi. Please ignore this issue, the board
> will be compiled clean at the next iteration after Jagan's tree will be
> merged by Tom.
>
> The following changes since commit a6bc0195dba895fa0e9facc718d17eb098695685:
>
> Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'
> (2014-09-09 09:19:10 +0200)
>
> are available in the git repository at:
>
>
> git://www.denx.de/git/u-boot-imx.git master
>
> for you to fetch changes up to 4c97f16911e229f6d5bbea5bee52449916e5fa92:
>
> imx: mx6slevk: Change to use generic board (2014-09-11 11:04:26 +0200)
>
> ----------------------------------------------------------------
> Fabio Estevam (9):
> net: fec_mxc: Adjust RX DMA alignment for mx6solox
> net: fec_mxc: Poll FEC_TBD_READY after polling TDAR
> tools: imximage: Fix the maximum DCD size for mx53/mx6
> mx6dlsabresd: Use its own DCD table
> mx6qsabreauto: Remove imx6q-sabreauto.dts
> mx6: imx-regs: Provide a structure for GPC registers
> pcie_imx: Add mx6solox support
> mx6sxsabresd: Add PCI support
> README.imximage: Fix the maximum DCD size
>
> Guillaume GARDET (1):
> imx: nitrogen6x: Replace 'fatload' by 'load' command in env
> settings to be filesystem independent
>
> Nikita Kiryanov (16):
> mx6: add clock enabling functions
> compulab: eeprom: add support for defining eeprom i2c bus
> sata: dwc_ahsata: implement sata_port_status
> i2c: imx: add macros to setup pads for multiple SoC types
> arm: mx6: ddr: cleanup
> arm: mx6: ddr: do not write into reserved bit
> arm: mx6: ddr: configure MMDC for slow_pd
> arm: mx6: ddr: fix cs0_end calculation
> arm: mx6: add get_cpu_type()
> arm: mx6: add support for Compulab cm-fx6 CoM
> arm: mx6: cm_fx6: add nand support
> arm: mx6: cm_fx6: add ethernet support
> arm: mx6: cm_fx6: add usb support
> arm: mx6: cm_fx6: add i2c support
> arm: mx6: cm_fx6: use eeprom
> arm: mx6: cm_fx6: add sata support
>
> Nikolay Dimitrov (1):
> mx6: Fix ECSPI typo in soc_boot_modes
>
> Stefan Agner (2):
> arm: vf610: lpuart: fix status register handling
> arm: vf610: lpuart: disable FIFO on initializaton
>
> Stefano Babic (1):
> imx: Fix build of mx6sxsabresd
>
> Thierry Reding (1):
> imx: ventana: Avoid undefined behaviour
>
> Tim Harvey (6):
> imx: ventana: updated notes regarding NAND boot errata
> imx: ventana: base SPL MMDC calibration on width and size not board
> imx: ventana: add GW5520 support
> imx: ventana: added cputype env var
> pci: add support for board_pci_fixup_dev function
> imx: ventana: add pci fixup for PLX PEX860x switch GPIO
>
> Ye.Li (4):
> iMX6: Disable the L2 before chaning the PL310 latency
> imximage: Fix imximage IVT bug for EIM-NOR boot
> imx: mx6q/dlarm2: Change to use generic board
> imx: mx6slevk: Change to use generic board
>
> arch/arm/Kconfig | 4 +
> arch/arm/cpu/armv7/mx6/clock.c | 107 +++++-
> arch/arm/cpu/armv7/mx6/ddr.c | 277 ++++++++--------
> arch/arm/cpu/armv7/mx6/soc.c | 11 +-
> arch/arm/dts/Makefile | 1 -
> arch/arm/dts/imx6q-sabreauto.dts | 13 -
> arch/arm/include/asm/arch-mx6/clock.h | 5 +
> arch/arm/include/asm/arch-mx6/imx-regs.h | 13 +
> arch/arm/include/asm/arch-mx6/iomux.h | 9 +
> arch/arm/include/asm/arch-mx6/sys_proto.h | 5 +-
> arch/arm/include/asm/imx-common/mxc_i2c.h | 33 ++
> board/compulab/cm_fx6/Kconfig | 23 ++
> board/compulab/cm_fx6/MAINTAINERS | 6 +
> board/compulab/cm_fx6/Makefile | 12 +
> board/compulab/cm_fx6/cm_fx6.c | 483
> ++++++++++++++++++++++++++++
> board/compulab/cm_fx6/common.c | 84 +++++
> board/compulab/cm_fx6/common.h | 37 +++
> board/compulab/cm_fx6/imximage.cfg | 8 +
> board/compulab/cm_fx6/spl.c | 366 +++++++++++++++++++++
> board/compulab/common/eeprom.c | 13 +-
> board/freescale/mx6sabresd/mx6dlsabresd.cfg | 131 ++++++++
> board/gateworks/gw_ventana/eeprom.c | 3 +
> board/gateworks/gw_ventana/gsc.c | 4 +
> board/gateworks/gw_ventana/gw_ventana.c | 118 ++++++-
> board/gateworks/gw_ventana/gw_ventana_spl.c | 189 ++++++-----
> board/gateworks/gw_ventana/ventana_eeprom.h | 1 +
> configs/cm_fx6_defconfig | 4 +
> configs/mx6dlsabresd_defconfig | 2 +-
> doc/README.imximage | 2 +-
> drivers/block/dwc_ahsata.c | 17 +
> drivers/net/fec_mxc.c | 42 ++-
> drivers/pci/pci.c | 4 +
> drivers/pci/pcie_imx.c | 40 ++-
> drivers/serial/serial_lpuart.c | 19 +-
> include/configs/cm_fx6.h | 290 +++++++++++++++++
> include/configs/cm_t335.h | 1 +
> include/configs/cm_t35.h | 1 +
> include/configs/cm_t54.h | 1 +
> include/configs/gw_ventana.h | 1 +
> include/configs/mx6qarm2.h | 2 +
> include/configs/mx6qsabreauto.h | 3 -
> include/configs/mx6slevk.h | 2 +
> include/configs/mx6sxsabresd.h | 10 +
> include/configs/nitrogen6x.h | 6 +-
> include/pci.h | 7 +
> include/sata.h | 1 +
> tools/imximage.c | 7 +
> tools/imximage.h | 2 +-
> 48 files changed, 2140 insertions(+), 280 deletions(-)
> delete mode 100644 arch/arm/dts/imx6q-sabreauto.dts
> create mode 100644 board/compulab/cm_fx6/Kconfig
> create mode 100644 board/compulab/cm_fx6/MAINTAINERS
> create mode 100644 board/compulab/cm_fx6/Makefile
> create mode 100644 board/compulab/cm_fx6/cm_fx6.c
> create mode 100644 board/compulab/cm_fx6/common.c
> create mode 100644 board/compulab/cm_fx6/common.h
> create mode 100644 board/compulab/cm_fx6/imximage.cfg
> create mode 100644 board/compulab/cm_fx6/spl.c
> create mode 100644 board/freescale/mx6sabresd/mx6dlsabresd.cfg
> create mode 100644 configs/cm_fx6_defconfig
> create mode 100644 include/configs/cm_fx6.h
>
> Best regards,
> Stefano
>
Applied to u-boot-arm/master [1], thanks!
[1] with two boards (trimslice and cm_fx6)temporarily failing to build
until spi tree gets pulled)
Amicalement,
--
Albert.
More information about the U-Boot
mailing list