[U-Boot] [PATCH v2 7/7] arm: ls102xa: Add SD boot support for LS1021ATWR board
Alison Wang
b18965 at freescale.com
Fri Sep 26 12:33:42 CEST 2014
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu at freescale.com>
Signed-off-by: Alison Wang <alison.wang at freescale.com>
Signed-off-by: Jason Jin <jason.jin at freescale.com>
---
Change log:
v2: Use generic u-boot-spl.lds.
board/freescale/ls1021atwr/ls1021atwr.c | 31 +++++++++++++++-
board/freescale/ls1021atwr/ls102xa_pbi.cfg | 13 +++++++
board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg | 14 ++++++++
configs/ls1021atwr_sdcard_defconfig | 4 +++
include/configs/ls1021atwr.h | 52 +++++++++++++++++++++++++++
5 files changed, 113 insertions(+), 1 deletion(-)
create mode 100644 board/freescale/ls1021atwr/ls102xa_pbi.cfg
create mode 100644 board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg
create mode 100644 configs/ls1021atwr_sdcard_defconfig
diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c
index b522ff2..7c0654a 100644
--- a/board/freescale/ls1021atwr/ls1021atwr.c
+++ b/board/freescale/ls1021atwr/ls1021atwr.c
@@ -16,6 +16,7 @@
#include <netdev.h>
#include <fsl_mdio.h>
#include <tsec.h>
+#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -65,6 +66,7 @@ struct cpld_data {
u8 rev2; /* Reserved */
};
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
static void convert_serdes_mux(int type, int need_reset);
void cpld_show(void)
@@ -100,11 +102,14 @@ void cpld_show(void)
in_8(&cpld_data->serdes_mux));
#endif
}
+#endif
int checkboard(void)
{
puts("Board: LS1021ATWR\n");
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
cpld_show();
+#endif
return 0;
}
@@ -213,6 +218,7 @@ int board_eth_init(bd_t *bis)
}
#endif
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
int config_serdes_mux(void)
{
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
@@ -244,6 +250,7 @@ int config_serdes_mux(void)
return 0;
}
+#endif
int board_early_init_f(void)
{
@@ -270,13 +277,33 @@ int board_early_init_f(void)
return 0;
}
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong dummy)
+{
+ /* Set global data pointer */
+ gd = &gdata;
+
+ /* Clear the BSS */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ get_clocks();
+
+ preloader_console_init();
+
+ dram_init();
+
+ board_init_r(NULL, 0);
+}
+#endif
+
int board_init(void)
{
#ifndef CONFIG_SYS_FSL_NO_SERDES
fsl_serdes_init();
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
config_serdes_mux();
#endif
-
+#endif
return 0;
}
@@ -304,6 +331,7 @@ u16 flash_read16(void *addr)
return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
}
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
static void convert_flash_bank(char bank)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
@@ -486,3 +514,4 @@ U_BOOT_CMD(
" -change lane C & lane D to PCIeX2\n"
"\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n"
);
+#endif
diff --git a/board/freescale/ls1021atwr/ls102xa_pbi.cfg b/board/freescale/ls1021atwr/ls102xa_pbi.cfg
new file mode 100644
index 0000000..76373ce
--- /dev/null
+++ b/board/freescale/ls1021atwr/ls102xa_pbi.cfg
@@ -0,0 +1,13 @@
+#PBI commands
+
+09570200 ffffffff
+09570158 00000300
+09570200 00000000
+8940007c 21f47300
+
+#Configure Scratch register
+09ee0200 10000000
+#Configure alternate space
+09570158 00080000
+#Flush PBL data
+096100c0 000FFFFF
diff --git a/board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg b/board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg
new file mode 100644
index 0000000..6c83e3b
--- /dev/null
+++ b/board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg
@@ -0,0 +1,14 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+
+#enable IFC, disable QSPI and DSPI
+#0608000a 00000000 00000000 00000000
+#20000000 00404000 60025a00 21042000
+#00200000 00000000 00000000 01038000
+#00000000 001b1200 00000000 00000000
+
+#disable IFC, enable QSPI and DSPI
+0608000a 00000000 00000000 00000000
+20000000 00407900 60025a00 21046000
+00000000 00000000 00000000 01038000
+20024800 881b1540 00000000 00000000
diff --git a/configs/ls1021atwr_sdcard_defconfig b/configs/ls1021atwr_sdcard_defconfig
new file mode 100644
index 0000000..0eb556a
--- /dev/null
+++ b/configs/ls1021atwr_sdcard_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_LS1021ATWR=y
diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h
index 45b2272..cbf4082 100644
--- a/include/configs/ls1021atwr.h
+++ b/include/configs/ls1021atwr.h
@@ -35,6 +35,40 @@
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg
+#endif
+
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg
+#define CONFIG_SPL_PBL_PAD
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+
+#define CONFIG_SPL_TEXT_BASE 0x10000000
+#define CONFIG_SPL_MAX_SIZE 0x1a000
+#define CONFIG_SPL_STACK 0x1001d000
+#define CONFIG_SPL_PAD_TO 0x1c000
+#define CONFIG_SYS_TEXT_BASE 0x82000000
+
+#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+#define CONFIG_SPL_BSS_START_ADDR 0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_MONITOR_LEN 0x80000
+#define CONFIG_SYS_NO_FLASH
+#endif
+
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0x67f80000
#endif
@@ -51,6 +85,7 @@
/*
* IFC Definitions
*/
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE 0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
@@ -93,6 +128,7 @@
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#endif
/* CPLD */
@@ -225,7 +261,12 @@
#define CONFIG_CMDLINE_TAG
#define CONFIG_CMDLINE_EDITING
+
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
#define CONFIG_CMD_IMLS
+#else
+#undef CONFIG_CMD_IMLS
+#endif
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
@@ -272,17 +313,28 @@
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
+#if defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x20000
+#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
--
2.1.0.27.g96db324
More information about the U-Boot
mailing list