[U-Boot] [PATCH v4 2/2] imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boards
Ye.Li
B37916 at freescale.com
Mon Sep 29 17:26:29 CEST 2014
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916 at freescale.com>
---
Changes since v3:
- Add maintainer and status information
Changes since v2:
- Rework the short log subject
Changes since v1:
- The (CONFIG_DDR_32BIT) is true only for mx6dlarm2
board/freescale/mx6qarm2/MAINTAINERS | 2 +
board/freescale/mx6qarm2/imximage.cfg | 189 +++++++++++++++-
board/freescale/mx6qarm2/imximage_mx6dl.cfg | 319 +++++++++++++++++++++++++++
board/freescale/mx6qarm2/mx6qarm2.c | 7 +-
configs/mx6dlarm2_defconfig | 2 +-
configs/mx6dlarm2_lpddr2_defconfig | 3 +
configs/mx6qarm2_defconfig | 2 +-
configs/mx6qarm2_lpddr2_defconfig | 3 +
include/configs/mx6qarm2.h | 5 -
9 files changed, 518 insertions(+), 14 deletions(-)
create mode 100644 configs/mx6dlarm2_lpddr2_defconfig
create mode 100644 configs/mx6qarm2_lpddr2_defconfig
diff --git a/board/freescale/mx6qarm2/MAINTAINERS b/board/freescale/mx6qarm2/MAINTAINERS
index c8d594b..52cf7f9 100644
--- a/board/freescale/mx6qarm2/MAINTAINERS
+++ b/board/freescale/mx6qarm2/MAINTAINERS
@@ -6,3 +6,5 @@ F: board/freescale/mx6qarm2/
F: include/configs/mx6qarm2.h
F: configs/mx6qarm2_defconfig
F: configs/mx6dlarm2_defconfig
+F: configs/mx6qarm2_lpddr2_defconfig
+F: configs/mx6dlarm2_lpddr2_defconfig
diff --git a/board/freescale/mx6qarm2/imximage.cfg b/board/freescale/mx6qarm2/imximage.cfg
index 710f34d..c85bde5 100644
--- a/board/freescale/mx6qarm2/imximage.cfg
+++ b/board/freescale/mx6qarm2/imximage.cfg
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2011-2014 Freescale Semiconductor, Inc.
* Jason Liu <r64343 at freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
@@ -30,6 +30,185 @@ BOOT_FROM sd
* Address absolute address of the register
* value value to be stored in the register
*/
+#ifdef CONFIG_MX6DQ_LPDDR2
+/* DCD */
+DATA 4 0x020C4018 0x60324
+
+DATA 4 0x020E05a8 0x00003038
+DATA 4 0x020E05b0 0x00003038
+DATA 4 0x020E0524 0x00003038
+DATA 4 0x020E051c 0x00003038
+
+DATA 4 0x020E0518 0x00003038
+DATA 4 0x020E050c 0x00003038
+DATA 4 0x020E05b8 0x00003038
+DATA 4 0x020E05c0 0x00003038
+
+DATA 4 0x020E05ac 0x00000038
+DATA 4 0x020E05b4 0x00000038
+DATA 4 0x020E0528 0x00000038
+DATA 4 0x020E0520 0x00000038
+
+DATA 4 0x020E0514 0x00000038
+DATA 4 0x020E0510 0x00000038
+DATA 4 0x020E05bc 0x00000038
+DATA 4 0x020E05c4 0x00000038
+
+DATA 4 0x020E056c 0x00000038
+DATA 4 0x020E0578 0x00000038
+DATA 4 0x020E0588 0x00000038
+DATA 4 0x020E0594 0x00000038
+
+DATA 4 0x020E057c 0x00000038
+DATA 4 0x020E0590 0x00000038
+DATA 4 0x020E0598 0x00000038
+DATA 4 0x020E058c 0x00000000
+
+DATA 4 0x020E059c 0x00000038
+DATA 4 0x020E05a0 0x00000038
+DATA 4 0x020E0784 0x00000038
+DATA 4 0x020E0788 0x00000038
+
+DATA 4 0x020E0794 0x00000038
+DATA 4 0x020E079c 0x00000038
+DATA 4 0x020E07a0 0x00000038
+DATA 4 0x020E07a4 0x00000038
+
+DATA 4 0x020E07a8 0x00000038
+DATA 4 0x020E0748 0x00000038
+DATA 4 0x020E074c 0x00000038
+DATA 4 0x020E0750 0x00020000
+
+DATA 4 0x020E0758 0x00000000
+DATA 4 0x020E0774 0x00020000
+DATA 4 0x020E078c 0x00000038
+DATA 4 0x020E0798 0x00080000
+
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b401c 0x00008000
+
+DATA 4 0x021b085c 0x1b5f01ff
+DATA 4 0x021b485c 0x1b5f01ff
+
+DATA 4 0x021b0800 0xa1390000
+DATA 4 0x021b4800 0xa1390000
+
+DATA 4 0x021b0890 0x00400000
+DATA 4 0x021b4890 0x00400000
+
+DATA 4 0x021b48bc 0x00055555
+
+DATA 4 0x021b08b8 0x00000800
+DATA 4 0x021b48b8 0x00000800
+
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+DATA 4 0x021b481c 0x33333333
+DATA 4 0x021b4820 0x33333333
+DATA 4 0x021b4824 0x33333333
+DATA 4 0x021b4828 0x33333333
+
+DATA 4 0x021b082c 0xf3333333
+DATA 4 0x021b0830 0xf3333333
+DATA 4 0x021b0834 0xf3333333
+DATA 4 0x021b0838 0xf3333333
+DATA 4 0x021b482c 0xf3333333
+DATA 4 0x021b4830 0xf3333333
+DATA 4 0x021b4834 0xf3333333
+DATA 4 0x021b4838 0xf3333333
+
+DATA 4 0x021b0848 0x49383b39
+DATA 4 0x021b0850 0x30364738
+DATA 4 0x021b4848 0x3e3c3846
+DATA 4 0x021b4850 0x4c294b35
+
+DATA 4 0x021b083c 0x20000000
+DATA 4 0x021b0840 0x0
+DATA 4 0x021b483c 0x20000000
+DATA 4 0x021b4840 0x0
+
+DATA 4 0x021b0858 0xf00
+DATA 4 0x021b4858 0xf00
+
+DATA 4 0x021b08b8 0x800
+DATA 4 0x021b48b8 0x800
+
+DATA 4 0x021b000c 0x555a61a5
+DATA 4 0x021b0004 0x20036
+DATA 4 0x021b0010 0x160e83
+DATA 4 0x021b0014 0xdd
+DATA 4 0x021b0018 0x8174c
+DATA 4 0x021b002c 0xf9f26d2
+DATA 4 0x021b0030 0x20e
+DATA 4 0x021b0038 0x200aac
+DATA 4 0x021b0008 0x0
+
+DATA 4 0x021b0040 0x5f
+
+DATA 4 0x021b0000 0xc3010000
+
+DATA 4 0x021b400c 0x555a61a5
+DATA 4 0x021b4004 0x20036
+DATA 4 0x021b4010 0x160e83
+DATA 4 0x021b4014 0xdd
+DATA 4 0x021b4018 0x8174c
+DATA 4 0x021b402c 0xf9f26d2
+DATA 4 0x021b4030 0x20e
+DATA 4 0x021b4038 0x200aac
+DATA 4 0x021b4008 0x0
+
+DATA 4 0x021b4040 0x3f
+DATA 4 0x021b4000 0xc3010000
+
+DATA 4 0x021b001c 0x3f8030
+DATA 4 0x021b001c 0xff0a8030
+DATA 4 0x021b001c 0xc2018030
+DATA 4 0x021b001c 0x6028030
+DATA 4 0x021b001c 0x2038030
+
+DATA 4 0x021b401c 0x3f8030
+DATA 4 0x021b401c 0xff0a8030
+DATA 4 0x021b401c 0xc2018030
+DATA 4 0x021b401c 0x6028030
+DATA 4 0x021b401c 0x2038030
+
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b4800 0xa1390003
+
+DATA 4 0x021b0020 0x7800
+DATA 4 0x021b4020 0x7800
+
+DATA 4 0x021b0818 0x0
+DATA 4 0x021b4818 0x0
+
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b4800 0xa1390003
+
+DATA 4 0x021b08b8 0x800
+DATA 4 0x021b48b8 0x800
+
+DATA 4 0x021b001c 0x0
+DATA 4 0x021b401c 0x0
+
+DATA 4 0x021b0404 0x00011006
+
+DATA 4 0x020c4068 0x00C03F3F
+DATA 4 0x020c406c 0x0030FC03
+DATA 4 0x020c4070 0x0FFFC000
+DATA 4 0x020c4074 0x3FF00000
+DATA 4 0x020c4078 0x00FFF300
+DATA 4 0x020c407c 0x0F0000C3
+DATA 4 0x020c4080 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 0x020e0010 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
+
+#else
DATA 4 0x020e05a8 0x00000030
DATA 4 0x020e05b0 0x00000030
DATA 4 0x020e0524 0x00000030
@@ -142,12 +321,8 @@ DATA 4 0x021b48b8 0x00000800
DATA 4 0x021b001c 0x00000000
DATA 4 0x021b0404 0x00011006
-DATA 4 0x020e0010 0xF00000FF
-DATA 4 0x020e0018 0x00070007
-DATA 4 0x020e001c 0x00070007
-
DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC00
+DATA 4 0x020c406c 0x0030FC03
DATA 4 0x020c4070 0x0FFFC000
DATA 4 0x020c4074 0x3FF00000
DATA 4 0x020c4078 0x00FFF300
@@ -159,3 +334,5 @@ DATA 4 0x020e0010 0xF00000CF
/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
DATA 4 0x020e0018 0x007F007F
DATA 4 0x020e001c 0x007F007F
+
+#endif /* CONFIG_MX6DQ_LPDDR2 */
diff --git a/board/freescale/mx6qarm2/imximage_mx6dl.cfg b/board/freescale/mx6qarm2/imximage_mx6dl.cfg
index eef723c..ae8dcc6 100644
--- a/board/freescale/mx6qarm2/imximage_mx6dl.cfg
+++ b/board/freescale/mx6qarm2/imximage_mx6dl.cfg
@@ -30,6 +30,324 @@ BOOT_FROM sd
* Address absolute address of the register
* value value to be stored in the register
*/
+
+
+
+#ifdef CONFIG_MX6DL_LPDDR2
+
+/* IOMUX SETTINGS */
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 */
+DATA 4 0x020E04bc 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 */
+DATA 4 0x020E04c0 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 */
+DATA 4 0x020E04c4 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 */
+DATA 4 0x020E04c8 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS4 */
+DATA 4 0x020E04cc 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS5 */
+DATA 4 0x020E04d0 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS6 */
+DATA 4 0x020E04d4 0x00003028
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS7 */
+DATA 4 0x020E04d8 0x00003028
+
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+DATA 4 0x020E0470 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+DATA 4 0x020E0474 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM2 */
+DATA 4 0x020E0478 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM3 */
+DATA 4 0x020E047c 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM4 */
+DATA 4 0x020E0480 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM5 */
+DATA 4 0x020E0484 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM6 */
+DATA 4 0x020E0488 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM7 */
+DATA 4 0x020E048c 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+DATA 4 0x020E0464 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+DATA 4 0x020E0490 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0 */
+DATA 4 0x020E04ac 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_1 */
+DATA 4 0x020E04b0 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+DATA 4 0x020E0494 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCKE0 */
+DATA 4 0x020E04a4 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCKE1 */
+DATA 4 0x020E04a8 0x00000038
+/*
+ * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2
+ * DSE can be configured using Group Control Register:
+ * IOMUXC_SW_PAD_CTL_GRP_CTLDS
+ */
+DATA 4 0x020E04a0 0x00000000
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0 */
+DATA 4 0x020E04b4 0x00000038
+/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT1 */
+DATA 4 0x020E04b8 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+DATA 4 0x020E0764 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+DATA 4 0x020E0770 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B2DS */
+DATA 4 0x020E0778 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B3DS */
+DATA 4 0x020E077c 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B4DS */
+DATA 4 0x020E0780 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B5DS */
+DATA 4 0x020E0784 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B6DS */
+DATA 4 0x020E078c 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_B7DS */
+DATA 4 0x020E0748 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+DATA 4 0x020E074c 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+DATA 4 0x020E076c 0x00000038
+/* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+DATA 4 0x020E0750 0x00020000
+/* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+DATA 4 0x020E0754 0x00000000
+/* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+DATA 4 0x020E0760 0x00020000
+/* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+DATA 4 0x020E0774 0x00080000
+
+/*
+ * DDR Controller Registers
+ *
+ * Manufacturer: Mocron
+ * Device Part Number: MT42L64M64D2KH-18
+ * Clock Freq.: 528MHz
+ * MMDC channels: Both MMDC0, MMDC1
+ *Density per CS in Gb: 256M
+ * Chip Selects used: 2
+ * Number of Banks: 8
+ * Row address: 14
+ * Column address: 9
+ * Data bus width 32
+ */
+
+/* MMDC_P0_BASE_ADDR = 0x021b0000 */
+/* MMDC_P1_BASE_ADDR = 0x021b4000 */
+
+/* MMDC0_MDSCR, set the Configuration request bit during MMDC set up */
+DATA 4 0x021b001c 0x00008000
+
+/* MMDC0_MDSCR, set the Configuration request bit during MMDC set up */
+DATA 4 0x021b401c 0x00008000
+
+/*LPDDR2 ZQ params */
+DATA 4 0x021b085c 0x1b5f01ff
+DATA 4 0x021b485c 0x1b5f01ff
+
+/* Calibration setup. */
+/* DDR_PHY_P0_MPZQHWCTRL, enable on time ZQ calibration */
+DATA 4 0x021b0800 0xa1390003
+
+/*ca bus abs delay */
+DATA 4 0x021b0890 0x00400000
+/*ca bus abs delay */
+DATA 4 0x021b4890 0x00400000
+/* values of 20,40,50,60,7f tried. no difference seen */
+
+/* DDR_PHY_P1_MPWRCADL */
+DATA 4 0x021b48bc 0x00055555
+
+/*frc_msr.*/
+DATA 4 0x021b08b8 0x00000800
+/*frc_msr.*/
+DATA 4 0x021b48b8 0x00000800
+
+/* DDR_PHY_P0_MPREDQBY0DL3 */
+DATA 4 0x021b081c 0x33333333
+/* DDR_PHY_P0_MPREDQBY1DL3 */
+DATA 4 0x021b0820 0x33333333
+/* DDR_PHY_P0_MPREDQBY2DL3 */
+DATA 4 0x021b0824 0x33333333
+/* DDR_PHY_P0_MPREDQBY3DL3 */
+DATA 4 0x021b0828 0x33333333
+/* DDR_PHY_P1_MPREDQBY0DL3 */
+DATA 4 0x021b481c 0x33333333
+/* DDR_PHY_P1_MPREDQBY1DL3 */
+DATA 4 0x021b4820 0x33333333
+/* DDR_PHY_P1_MPREDQBY2DL3 */
+DATA 4 0x021b4824 0x33333333
+/* DDR_PHY_P1_MPREDQBY3DL3 */
+DATA 4 0x021b4828 0x33333333
+
+/*
+ * Read and write data delay, per byte.
+ * For optimized DDR operation it is recommended to run mmdc_calibration
+ * on your board, and replace 4 delay register assigns with resulted values
+ * Note:
+ * a. DQS gating is not relevant for LPDDR2. DSQ gating calibration section
+ * should be skipped, or the write/read calibration comming after that
+ * will stall
+ * b. The calibration code that runs for both MMDC0 & MMDC1 should be used.
+ */
+
+DATA 4 0x021b0848 0x4b4b524f
+DATA 4 0x021b4848 0x494f4c44
+
+DATA 4 0x021b0850 0x3c3d303c
+DATA 4 0x021b4850 0x3c343d38
+
+/*dqs gating dis */
+DATA 4 0x021b083c 0x20000000
+DATA 4 0x021b0840 0x0
+DATA 4 0x021b483c 0x20000000
+DATA 4 0x021b4840 0x0
+
+/*clk delay */
+DATA 4 0x021b0858 0xa00
+/*clk delay */
+DATA 4 0x021b4858 0xa00
+
+/*frc_msr */
+DATA 4 0x021b08b8 0x00000800
+/*frc_msr */
+DATA 4 0x021b48b8 0x00000800
+/* Calibration setup end */
+
+/* Channel0 - startng address 0x80000000 */
+/* MMDC0_MDCFG0 */
+DATA 4 0x021b000c 0x34386145
+
+/* MMDC0_MDPDC */
+DATA 4 0x021b0004 0x00020036
+/* MMDC0_MDCFG1 */
+DATA 4 0x021b0010 0x00100c83
+/* MMDC0_MDCFG2 */
+DATA 4 0x021b0014 0x000000Dc
+/* MMDC0_MDMISC */
+DATA 4 0x021b0018 0x0000174C
+/* MMDC0_MDRWD;*/
+DATA 4 0x021b002c 0x0f9f26d2
+/* MMDC0_MDOR */
+DATA 4 0x021b0030 0x0000020e
+/* MMDC0_MDCFG3LP */
+DATA 4 0x021b0038 0x00190778
+/* MMDC0_MDOTC */
+DATA 4 0x021b0008 0x00000000
+
+/* CS0_END */
+DATA 4 0x021b0040 0x0000005f
+/* ROC */
+DATA 4 0x021b0404 0x0000000f
+
+/* MMDC0_MDCTL */
+DATA 4 0x021b0000 0xc3010000
+
+/* Channel1 - starting address 0x10000000 */
+/* MMDC1_MDCFG0 */
+DATA 4 0x021b400c 0x34386145
+
+/* MMDC1_MDPDC */
+DATA 4 0x021b4004 0x00020036
+/* MMDC1_MDCFG1 */
+DATA 4 0x021b4010 0x00100c83
+/* MMDC1_MDCFG2 */
+DATA 4 0x021b4014 0x000000Dc
+/* MMDC1_MDMISC */
+DATA 4 0x021b4018 0x0000174C
+/* MMDC1_MDRWD;*/
+DATA 4 0x021b402c 0x0f9f26d2
+/* MMDC1_MDOR */
+DATA 4 0x021b4030 0x0000020e
+/* MMDC1_MDCFG3LP */
+DATA 4 0x021b4038 0x00190778
+/* MMDC1_MDOTC */
+DATA 4 0x021b4008 0x00000000
+
+/* CS0_END */
+DATA 4 0x021b4040 0x0000003f
+
+/* MMDC1_MDCTL */
+DATA 4 0x021b4000 0xc3010000
+
+/* Channel0 : Configure DDR device:*/
+/* MRW: BA=0 CS=0 MR_ADDR=63 MR_OP=0 */
+DATA 4 0x021b001c 0x003f8030
+/* MRW: BA=0 CS=0 MR_ADDR=10 MR_OP=ff */
+DATA 4 0x021b001c 0xff0a8030
+/* MRW: BA=0 CS=0 MR_ADDR=1 MR_OP=a2 */
+DATA 4 0x021b001c 0xa2018030
+/* MRW: BA=0 CS=0 MR_ADDR=2 MR_OP=6. tcl=8, tcwl=4 */
+DATA 4 0x021b001c 0x06028030
+/* MRW: BA=0 CS=0 MR_ADDR=3 MR_OP=2.drive=240/6 */
+DATA 4 0x021b001c 0x01038030
+
+/* Channel1 : Configure DDR device:*/
+/* MRW: BA=0 CS=0 MR_ADDR=63 MR_OP=0 */
+DATA 4 0x021b401c 0x003f8030
+/* MRW: BA=0 CS=0 MR_ADDR=10 MR_OP=ff */
+DATA 4 0x021b401c 0xff0a8030
+/* MRW: BA=0 CS=0 MR_ADDR=1 MR_OP=a2 */
+DATA 4 0x021b401c 0xa2018030
+/* MRW: BA=0 CS=0 MR_ADDR=2 MR_OP=6. tcl=8, tcwl=4 */
+DATA 4 0x021b401c 0x06028030
+/* MRW: BA=0 CS=0 MR_ADDR=3 MR_OP=2.drive=240/6 */
+DATA 4 0x021b401c 0x01038030
+
+/* MMDC0_MDREF */
+DATA 4 0x021b0020 0x00005800
+/* MMDC1_MDREF */
+DATA 4 0x021b4020 0x00005800
+
+/* DDR_PHY_P0_MPODTCTRL */
+DATA 4 0x021b0818 0x0
+/* DDR_PHY_P1_MPODTCTRL */
+DATA 4 0x021b4818 0x0
+
+/*
+ * calibration values based on calibration compare of 0x00ffff00:
+ * Note, these calibration values are based on Freescale's board
+ * May need to run calibration on target board to fine tune these
+ */
+
+/* DDR_PHY_P0_MPZQHWCTRL, enable automatic ZQ calibration */
+DATA 4 0x021b0800 0xa1310003
+
+/* DDR_PHY_P0_MPMUR0, frc_msr */
+DATA 4 0x021b08b8 0x00000800
+/* DDR_PHY_P1_MPMUR0, frc_msr */
+DATA 4 0x021b48b8 0x00000800
+
+/*
+ * MMDC0_MDSCR, clear this register
+ * (especially the configuration bit as initialization is complete)
+ */
+DATA 4 0x021b001c 0x00000000
+/*
+ * MMDC0_MDSCR, clear this register
+ * (especially the configuration bit as initialization is complete)
+ */
+DATA 4 0x021b401c 0x00000000
+
+DATA 4 0x020c4068 0x00C03F3F
+DATA 4 0x020c406c 0x0030FC03
+DATA 4 0x020c4070 0x0FFFC000
+DATA 4 0x020c4074 0x3FF00000
+DATA 4 0x020c4078 0x00FFF300
+DATA 4 0x020c407c 0x0F0000C3
+DATA 4 0x020c4080 0x000003FF
+
+DATA 4 0x020e0010 0xF00000CF
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
+
+#else /* CONFIG_MX6DL_LPDDR2 */
+
DATA 4 0x020e0798 0x000c0000
DATA 4 0x020e0758 0x00000000
DATA 4 0x020e0588 0x00000030
@@ -141,3 +459,4 @@ DATA 4 0x020c4080 0x000003FF
DATA 4 0x020e0010 0xF00000CF
DATA 4 0x020e0018 0x007F007F
DATA 4 0x020e001c 0x007F007F
+#endif /* CONFIG_MX6DL_LPDDR2 */
diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c
index f2e577d..667dca5 100644
--- a/board/freescale/mx6qarm2/mx6qarm2.c
+++ b/board/freescale/mx6qarm2/mx6qarm2.c
@@ -32,7 +32,12 @@ DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+#if defined(CONFIG_MX6DL) && !defined(CONFIG_MX6DL_LPDDR2) && \
+ defined(CONFIG_DDR_32BIT)
+ gd->ram_size = ((phys_size_t)CONFIG_DDR_MB * 1024 * 1024) / 2;
+#else
+ gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
+#endif
return 0;
}
diff --git a/configs/mx6dlarm2_defconfig b/configs/mx6dlarm2_defconfig
index b4b78e5..de0193f 100644
--- a/configs/mx6dlarm2_defconfig
+++ b/configs/mx6dlarm2_defconfig
@@ -1,3 +1,3 @@
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage_mx6dl.cfg,MX6DL"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage_mx6dl.cfg,MX6DL,DDR_MB=2048"
CONFIG_ARM=y
CONFIG_TARGET_MX6QARM2=y
diff --git a/configs/mx6dlarm2_lpddr2_defconfig b/configs/mx6dlarm2_lpddr2_defconfig
new file mode 100644
index 0000000..cc432cf
--- /dev/null
+++ b/configs/mx6dlarm2_lpddr2_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage_mx6dl.cfg,MX6DL,MX6DL_LPDDR2,DDR_MB=512"
+CONFIG_ARM=y
+CONFIG_TARGET_MX6QARM2=y
diff --git a/configs/mx6qarm2_defconfig b/configs/mx6qarm2_defconfig
index a251615..3fe3559 100644
--- a/configs/mx6qarm2_defconfig
+++ b/configs/mx6qarm2_defconfig
@@ -1,3 +1,3 @@
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg,MX6Q"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg,MX6Q,DDR_MB=2048"
CONFIG_ARM=y
CONFIG_TARGET_MX6QARM2=y
diff --git a/configs/mx6qarm2_lpddr2_defconfig b/configs/mx6qarm2_lpddr2_defconfig
new file mode 100644
index 0000000..491e22a
--- /dev/null
+++ b/configs/mx6qarm2_lpddr2_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg,MX6Q,MX6DQ_LPDDR2,DDR_MB=512"
+CONFIG_ARM=y
+CONFIG_TARGET_MX6QARM2=y
diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h
index ed57e4a..6e01fa0 100644
--- a/include/configs/mx6qarm2.h
+++ b/include/configs/mx6qarm2.h
@@ -168,11 +168,6 @@
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-#ifdef CONFIG_DDR_32BIT
-#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
-#else
-#define PHYS_SDRAM_SIZE (2u * 1024 * 1024 * 1024)
-#endif
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
--
1.7.4.1
More information about the U-Boot
mailing list