[U-Boot] [RESEND PATCH 5/6] usb: host: Add ehci-vf USB driver for ARM Vybrid SoC's
Sanchayan Maity
maitysanchayan at gmail.com
Wed Apr 1 11:54:22 CEST 2015
Signed-off-by: Sanchayan Maity <maitysanchayan at gmail.com>
---
arch/arm/include/asm/arch-vf610/crm_regs.h | 14 ++
arch/arm/include/asm/arch-vf610/imx-regs.h | 4 +
drivers/usb/host/Makefile | 1 +
drivers/usb/host/ehci-vf.c | 204 +++++++++++++++++++++++++++++
4 files changed, 223 insertions(+)
create mode 100644 drivers/usb/host/ehci-vf.c
diff --git a/arch/arm/include/asm/arch-vf610/crm_regs.h b/arch/arm/include/asm/arch-vf610/crm_regs.h
index 78708e2..851c3b9 100644
--- a/arch/arm/include/asm/arch-vf610/crm_regs.h
+++ b/arch/arm/include/asm/arch-vf610/crm_regs.h
@@ -124,6 +124,10 @@ struct anadig_reg {
#define CCM_CCSR_PLL1_PFD_CLK_SEL_MASK (0x7 << 16)
#define CCM_CCSR_PLL1_PFD_CLK_SEL(v) (((v) & 0x7) << 16)
+#define CCM_CCSR_PLL3_PFD4_EN (1 << 31)
+#define CCM_CCSR_PLL3_PFD3_EN (1 << 30)
+#define CCM_CCSR_PLL3_PFD2_EN (1 << 29)
+#define CCM_CCSR_PLL3_PFD1_EN (1 << 28)
#define CCM_CCSR_PLL2_PFD4_EN (1 << 15)
#define CCM_CCSR_PLL2_PFD3_EN (1 << 14)
#define CCM_CCSR_PLL2_PFD2_EN (1 << 13)
@@ -189,6 +193,7 @@ struct anadig_reg {
#define CCM_REG_CTRL_MASK 0xffffffff
#define CCM_CCGR0_UART0_CTRL_MASK (0x3 << 14)
#define CCM_CCGR0_UART1_CTRL_MASK (0x3 << 16)
+#define CCM_CCGR1_USBC0_CTRL_MASK (0x3 << 8)
#define CCM_CCGR1_PIT_CTRL_MASK (0x3 << 14)
#define CCM_CCGR1_WDOGA5_CTRL_MASK (0x3 << 28)
#define CCM_CCGR2_QSPI0_CTRL_MASK (0x3 << 8)
@@ -207,14 +212,23 @@ struct anadig_reg {
#define CCM_CCGR6_OCOTP_CTRL_MASK (0x3 << 10)
#define CCM_CCGR6_DDRMC_CTRL_MASK (0x3 << 28)
#define CCM_CCGR7_SDHC1_CTRL_MASK (0x3 << 4)
+#define CCM_CCGR7_USBC1_CTRL_MASK (0x3 << 8)
#define CCM_CCGR9_FEC0_CTRL_MASK 0x3
#define CCM_CCGR9_FEC1_CTRL_MASK (0x3 << 2)
#define CCM_CCGR10_NFC_CTRL_MASK 0x3
+#define ANADIG_PLL7_CTRL_BYPASS (1 << 16)
+#define ANADIG_PLL7_CTRL_ENABLE (1 << 13)
+#define ANADIG_PLL7_CTRL_POWERDOWN (1 << 12)
+#define ANADIG_PLL7_CTRL_DIV_SELECT (1 << 1)
#define ANADIG_PLL5_CTRL_BYPASS (1 << 16)
#define ANADIG_PLL5_CTRL_ENABLE (1 << 13)
#define ANADIG_PLL5_CTRL_POWERDOWN (1 << 12)
#define ANADIG_PLL5_CTRL_DIV_SELECT 1
+#define ANADIG_PLL3_CTRL_BYPASS (1 << 16)
+#define ANADIG_PLL3_CTRL_ENABLE (1 << 13)
+#define ANADIG_PLL3_CTRL_POWERDOWN (1 << 12)
+#define ANADIG_PLL3_CTRL_DIV_SELECT (1 << 1)
#define ANADIG_PLL2_CTRL_ENABLE (1 << 13)
#define ANADIG_PLL2_CTRL_POWERDOWN (1 << 12)
#define ANADIG_PLL2_CTRL_DIV_SELECT 1
diff --git a/arch/arm/include/asm/arch-vf610/imx-regs.h b/arch/arm/include/asm/arch-vf610/imx-regs.h
index a5908ca..26057fe 100644
--- a/arch/arm/include/asm/arch-vf610/imx-regs.h
+++ b/arch/arm/include/asm/arch-vf610/imx-regs.h
@@ -52,6 +52,7 @@
#define SAI2_BASE_ADDR (AIPS0_BASE_ADDR + 0x00031000)
#define SAI3_BASE_ADDR (AIPS0_BASE_ADDR + 0x00032000)
#define CRC_BASE_ADDR (AIPS0_BASE_ADDR + 0x00033000)
+#define USBC0_BASE_ADDR (AIPS0_BASE_ADDR + 0x00034000)
#define PDB_BASE_ADDR (AIPS0_BASE_ADDR + 0x00036000)
#define PIT_BASE_ADDR (AIPS0_BASE_ADDR + 0x00037000)
#define FTM0_BASE_ADDR (AIPS0_BASE_ADDR + 0x00038000)
@@ -65,6 +66,8 @@
#define QSPI0_BASE_ADDR (AIPS0_BASE_ADDR + 0x00044000)
#define IOMUXC_BASE_ADDR (AIPS0_BASE_ADDR + 0x00048000)
#define ANADIG_BASE_ADDR (AIPS0_BASE_ADDR + 0x00050000)
+#define USB_PHY0_BASE_ADDR (AIPS0_BASE_ADDR + 0x00050800)
+#define USB_PHY1_BASE_ADDR (AIPS0_BASE_ADDR + 0x00050C00)
#define SCSC_BASE_ADDR (AIPS0_BASE_ADDR + 0x00052000)
#define ASRC_BASE_ADDR (AIPS0_BASE_ADDR + 0x00060000)
#define SPDIF_BASE_ADDR (AIPS0_BASE_ADDR + 0x00061000)
@@ -84,6 +87,7 @@
#define DDR_BASE_ADDR (AIPS1_BASE_ADDR + 0x0002E000)
#define ESDHC0_BASE_ADDR (AIPS1_BASE_ADDR + 0x00031000)
#define ESDHC1_BASE_ADDR (AIPS1_BASE_ADDR + 0x00032000)
+#define USBC1_BASE_ADDR (AIPS1_BASE_ADDR + 0x00034000)
#define ENET_BASE_ADDR (AIPS1_BASE_ADDR + 0x00050000)
#define ENET1_BASE_ADDR (AIPS1_BASE_ADDR + 0x00051000)
#define NFC_BASE_ADDR (AIPS1_BASE_ADDR + 0x00060000)
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index eb6f34b..4bd9321 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_USB_EHCI_SUNXI) += ehci-sunxi.o
obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
obj-$(CONFIG_USB_EHCI_UNIPHIER) += ehci-uniphier.o
obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
+obj-$(CONFIG_USB_EHCI_VF) += ehci-vf.o
obj-$(CONFIG_USB_EHCI_RMOBILE) += ehci-rmobile.o
obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
diff --git a/drivers/usb/host/ehci-vf.c b/drivers/usb/host/ehci-vf.c
new file mode 100644
index 0000000..4aa3b9c
--- /dev/null
+++ b/drivers/usb/host/ehci-vf.c
@@ -0,0 +1,204 @@
+/*
+ * Copyright (c) 2015 Sanchayan Maity <sanchayan.maity at toradex.com>
+ * Copyright (C) 2015 Toradex AG
+ *
+ * Based on ehci-mx6 driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <errno.h>
+#include <linux/compiler.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <usb/ehci-fsl.h>
+
+#include "ehci.h"
+
+#define USB_NC_REG_OFFSET 0x00000800
+#define USBCx_CTRL_OFFSET 0x00000000
+#define USBCx_PHY_CTRL_OFFSET 0x00000018
+
+#define USBPHY_CTRL 0x00000030
+#define USBPHY_CTRL_SET 0x00000034
+#define USBPHY_CTRL_CLR 0x00000038
+#define USBPHY_CTRL_TOG 0x0000003c
+
+#define USBPHY_PWD 0x00000000
+#define USBPHY_TX 0x00000010
+#define USBPHY_RX 0x00000020
+#define USBPHY_DEBUG 0x00000050
+#define USBPHY_CTRL_SFTRST 0x80000000
+#define USBPHY_CTRL_CLKGATE 0x40000000
+#define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
+#define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
+#define USBPHY_CTRL_OTG_ID 0x08000000
+
+#define ANADIG_PLL_CTRL_BYPASS 0x00010000
+#define ANADIG_PLL_CTRL_ENABLE 0x00002000
+#define ANADIG_PLL_CTRL_POWER 0x00001000
+#define ANADIG_PLL_CTRL_EN_USB_CLKS 0x00000040
+
+#define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
+#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
+
+/* USBCMD */
+#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
+#define UCMD_RESET (1 << 1) /* controller reset */
+
+static const unsigned phy_bases[] = {
+ USB_PHY0_BASE_ADDR,
+ USB_PHY1_BASE_ADDR,
+};
+
+static const unsigned nc_reg_bases[] = {
+ USBC0_BASE_ADDR,
+ USBC1_BASE_ADDR,
+};
+
+static void usb_internal_phy_clock_gate(int index)
+{
+ u32 reg;
+ void __iomem *phy_reg;
+
+ phy_reg = (void __iomem *)phy_bases[index];
+ reg = __raw_readl(phy_reg + USBPHY_CTRL);
+ reg &= ~USBPHY_CTRL_CLKGATE;
+ __raw_writel(reg, phy_reg + USBPHY_CTRL_SET);
+}
+
+static void usb_power_config(int index)
+{
+ struct anadig_reg __iomem *anadig =
+ (struct anadig_reg __iomem *)ANADIG_BASE_ADDR;
+ void __iomem *pll_ctrl;
+ u32 reg;
+
+ switch (index) {
+ case 0:
+ pll_ctrl = &anadig->pll3_ctrl;
+ break;
+ case 1:
+ pll_ctrl = &anadig->pll7_ctrl;
+ break;
+ default:
+ return;
+ }
+
+ reg = __raw_readl(pll_ctrl);
+ reg &= ~ANADIG_PLL_CTRL_BYPASS;
+ __raw_writel(reg, pll_ctrl);
+
+ reg = __raw_readl(pll_ctrl);
+ reg |= ANADIG_PLL_CTRL_ENABLE | ANADIG_PLL_CTRL_POWER
+ | ANADIG_PLL_CTRL_EN_USB_CLKS;
+ __raw_writel(reg, pll_ctrl);
+}
+
+static void usb_phy_enable(int index, struct usb_ehci *ehci)
+{
+ void __iomem *phy_reg;
+ void __iomem *phy_ctrl;
+ void __iomem *usb_cmd;
+ u32 val;
+
+ phy_reg = (void __iomem *)phy_bases[index];
+ phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
+ usb_cmd = (void __iomem *)&ehci->usbcmd;
+
+ /* Stop then Reset */
+ val = __raw_readl(usb_cmd);
+ val &= ~UCMD_RUN_STOP;
+ __raw_writel(val, usb_cmd);
+ while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
+ ;
+
+ val = __raw_readl(usb_cmd);
+ val |= UCMD_RESET;
+ __raw_writel(val, usb_cmd);
+ while (__raw_readl(usb_cmd) & UCMD_RESET)
+ ;
+
+ /* Reset USBPHY module */
+ val = __raw_readl(phy_ctrl);
+ val |= USBPHY_CTRL_SFTRST;
+ __raw_writel(val, phy_ctrl);
+ udelay(10);
+
+ /* Remove CLKGATE and SFTRST */
+ val = __raw_readl(phy_ctrl);
+ val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
+ __raw_writel(val, phy_ctrl);
+ udelay(10);
+
+ /* Power up the PHY */
+ __raw_writel(0, phy_reg + USBPHY_PWD);
+ /* enable FS/LS device */
+ val = __raw_readl(phy_ctrl);
+ val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
+ __raw_writel(val, phy_ctrl);
+}
+
+static void usb_oc_config(int index)
+{
+ void __iomem *ctrl;
+ u32 val;
+
+ ctrl = (void __iomem *)(nc_reg_bases[index] + USB_NC_REG_OFFSET +
+ USBCx_CTRL_OFFSET);
+
+ val = __raw_readl(ctrl);
+ val |= UCTRL_OVER_CUR_POL;
+ __raw_writel(val, ctrl);
+
+ val = __raw_readl(ctrl);
+ val |= UCTRL_OVER_CUR_DIS;
+ __raw_writel(val, ctrl);
+}
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ struct usb_ehci *ehci;
+
+ if (index >= ARRAY_SIZE(nc_reg_bases))
+ return -EINVAL;
+
+ if (init == USB_INIT_DEVICE && index == 1)
+ return -ENODEV;
+ if (init == USB_INIT_HOST && index == 0)
+ return -ENODEV;
+
+ ehci = (struct usb_ehci *)nc_reg_bases[index];
+
+ usb_power_config(index);
+ usb_oc_config(index);
+ usb_internal_phy_clock_gate(index);
+ usb_phy_enable(index, ehci);
+
+ *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+ *hcor = (struct ehci_hcor *)((uint32_t)*hccr +
+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+ if (init == USB_INIT_DEVICE) {
+ setbits_le32(&ehci->usbmode, CM_DEVICE);
+ __raw_writel((PORT_PTS_UTMI | PORT_PTS_PTW), &ehci->portsc);
+ setbits_le32(&ehci->portsc, USB_EN);
+ } else if (init == USB_INIT_HOST) {
+ setbits_le32(&ehci->usbmode, CM_HOST);
+ __raw_writel((PORT_PTS_UTMI | PORT_PTS_PTW), &ehci->portsc);
+ setbits_le32(&ehci->portsc, USB_EN);
+ }
+
+ return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+ return 0;
+}
--
2.3.4
More information about the U-Boot
mailing list