[U-Boot] [PATCH v1] dm: sf: Add Atmel DataFlash spi flash driver
Haikun Wang
haikun.wang at freescale.com
Fri Apr 17 12:58:27 CEST 2015
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Signed-off-by: Haikun Wang <haikun.wang at freescale.com>
---
drivers/mtd/spi/Makefile | 1 +
drivers/mtd/spi/spi_dataflash.c | 674 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 675 insertions(+)
create mode 100644 drivers/mtd/spi/spi_dataflash.c
diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
index c61b784..51de583 100644
--- a/drivers/mtd/spi/Makefile
+++ b/drivers/mtd/spi/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_SPL_SPI_LOAD) += spi_spl_load.o
obj-$(CONFIG_SPL_SPI_BOOT) += fsl_espi_spl.o
endif
+obj-$(CONFIG_DM_SPI_DATAFLASH) += spi_dataflash.o
#ifndef CONFIG_DM_SPI
obj-$(CONFIG_SPI_FLASH) += sf_probe.o
#endif
diff --git a/drivers/mtd/spi/spi_dataflash.c b/drivers/mtd/spi/spi_dataflash.c
new file mode 100644
index 0000000..0b92964
--- /dev/null
+++ b/drivers/mtd/spi/spi_dataflash.c
@@ -0,0 +1,674 @@
+/*
+ *
+ * Atmel DataFlash probing
+ *
+ * Copyright (C) 2004-2009, 2015 Freescale Semiconductor, Inc.
+ * Haikun Wang (haikun.wang at freescale.com)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+*/
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <malloc.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <asm/io.h>
+#include <div64.h>
+#include <linux/err.h>
+#include <linux/math64.h>
+
+#include "sf_internal.h"
+
+/*
+ * DataFlash is a kind of SPI flash. Most AT45 chips have two buffers in
+ * each chip, which may be used for double buffered I/O; but this driver
+ * doesn't (yet) use these for any kind of i/o overlap or prefetching.
+ *
+ * Sometimes DataFlash is packaged in MMC-format cards, although the
+ * MMC stack can't (yet?) distinguish between MMC and DataFlash
+ * protocols during enumeration.
+ */
+
+/* reads can bypass the buffers */
+#define OP_READ_CONTINUOUS 0xE8
+#define OP_READ_PAGE 0xD2
+
+/* group B requests can run even while status reports "busy" */
+#define OP_READ_STATUS 0xD7 /* group B */
+
+/* move data between host and buffer */
+#define OP_READ_BUFFER1 0xD4 /* group B */
+#define OP_READ_BUFFER2 0xD6 /* group B */
+#define OP_WRITE_BUFFER1 0x84 /* group B */
+#define OP_WRITE_BUFFER2 0x87 /* group B */
+
+/* erasing flash */
+#define OP_ERASE_PAGE 0x81
+#define OP_ERASE_BLOCK 0x50
+
+/* move data between buffer and flash */
+#define OP_TRANSFER_BUF1 0x53
+#define OP_TRANSFER_BUF2 0x55
+#define OP_MREAD_BUFFER1 0xD4
+#define OP_MREAD_BUFFER2 0xD6
+#define OP_MWERASE_BUFFER1 0x83
+#define OP_MWERASE_BUFFER2 0x86
+#define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */
+#define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */
+
+/* write to buffer, then write-erase to flash */
+#define OP_PROGRAM_VIA_BUF1 0x82
+#define OP_PROGRAM_VIA_BUF2 0x85
+
+/* compare buffer to flash */
+#define OP_COMPARE_BUF1 0x60
+#define OP_COMPARE_BUF2 0x61
+
+/* read flash to buffer, then write-erase to flash */
+#define OP_REWRITE_VIA_BUF1 0x58
+#define OP_REWRITE_VIA_BUF2 0x59
+
+/* newer chips report JEDEC manufacturer and device IDs; chip
+ * serial number and OTP bits; and per-sector writeprotect.
+ */
+#define OP_READ_ID 0x9F
+#define OP_READ_SECURITY 0x77
+#define OP_WRITE_SECURITY_REVC 0x9A
+#define OP_WRITE_SECURITY 0x9B /* revision D */
+
+
+struct dataflash {
+ uint8_t command[16];
+ unsigned short page_offset; /* offset in flash address */
+ struct spi_flash *flash;
+};
+
+/* ......................................................................... */
+
+/*
+ * Return the status of the DataFlash device.
+ */
+static inline int dataflash_status(struct spi_slave *spi)
+{
+ int ret;
+ char status;
+ /* NOTE: at45db321c over 25 MHz wants to write
+ * a dummy byte after the opcode...
+ */
+ ret = spi_flash_cmd(spi, OP_READ_STATUS, &status, 1);
+ return ret ? -EIO : status;
+}
+
+/*
+ * Poll the DataFlash device until it is READY.
+ * This usually takes 5-20 msec or so; more for sector erase.
+ * ready: return > 0
+ */
+static int dataflash_waitready(struct spi_slave *spi)
+{
+ int status;
+ int timeout = 1000;
+
+ for (; timeout-- ;) {
+ status = dataflash_status(spi);
+ if (status < 0)
+ status = 0;
+
+ if (status & (1 << 7)) /* RDY/nBSY */
+ return status;
+
+ mdelay(3);
+ }
+
+ return -ETIME;
+}
+
+/* ......................................................................... */
+
+/*
+ * Erase pages of flash.
+ */
+static int spi_dataflash_erase(struct udevice *dev, u32 offset, size_t len)
+{
+ struct dataflash *dataflash;
+ struct spi_flash *spi_flash;
+ struct spi_slave *spi;
+ unsigned blocksize;
+ uint8_t *command;
+ uint32_t rem;
+
+ dataflash = dev->priv;
+ spi_flash = dataflash->flash;
+ spi = spi_flash->spi;
+
+ blocksize = spi_flash->page_size << 3;
+
+ memset(dataflash->command, 0 , sizeof(dataflash->command));
+
+ debug("%s: erase addr=0x%llx len 0x%llx\n",
+ dev->name, (long long)offset, (long long)len);
+
+ div_u64_rem(len, spi_flash->page_size, &rem);
+ if (rem)
+ return -EINVAL;
+ div_u64_rem(offset, spi_flash->page_size, &rem);
+ if (rem)
+ return -EINVAL;
+
+ command = dataflash->command;
+
+ while (len > 0) {
+ unsigned int pageaddr;
+ int status;
+ int do_block;
+
+ /* Calculate flash page address; use block erase (for speed) if
+ * we're at a block boundary and need to erase the whole block.
+ */
+ pageaddr = div_u64(offset, spi_flash->page_size);
+ do_block = (pageaddr & 0x7) == 0 && len >= blocksize;
+ pageaddr = pageaddr << dataflash->page_offset;
+
+ command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
+ command[1] = (uint8_t)(pageaddr >> 16);
+ command[2] = (uint8_t)(pageaddr >> 8);
+ command[3] = 0;
+
+ debug("ERASE %s: (%x) %x %x %x [%i]\n",
+ do_block ? "block" : "page",
+ command[0], command[1], command[2], command[3],
+ pageaddr);
+
+ status = spi_flash_write_common(spi_flash, command, 4, NULL, 0);
+ if (status < 0)
+ return -EIO;
+
+ status = dataflash_waitready(spi);
+ if (status < 0)
+ return status;
+
+ if (do_block) {
+ offset += blocksize;
+ len -= blocksize;
+ } else {
+ offset += spi_flash->page_size;
+ len -= spi_flash->page_size;
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * Read from the DataFlash device.
+ * from : Start offset in flash device
+ * len : Amount to read
+ * retlen : About of data actually read
+ * buf : Buffer containing the data
+ */
+static int spi_dataflash_read(struct udevice *dev, u32 offset, size_t len,
+ void *buf)
+{
+ struct dataflash *dataflash;
+ struct spi_flash *spi_flash;
+ unsigned int addr;
+ uint8_t *command;
+ int status;
+
+ dataflash = dev->priv;
+ spi_flash = dataflash->flash;
+
+ memset(dataflash->command, 0 , sizeof(dataflash->command));
+
+ debug("%s: erase addr=0x%llx len 0x%llx\n",
+ dev->name, (long long)offset, (long long)len);
+ debug("READ: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ /* Calculate flash page/byte address */
+ addr = (((unsigned)offset / spi_flash->page_size)
+ << dataflash->page_offset)
+ + ((unsigned)offset % spi_flash->page_size);
+
+ command = dataflash->command;
+
+ /* Continuous read, max clock = f(car) which may be less than
+ * the peak rate available. Some chips support commands with
+ * fewer "don't care" bytes. Both buffers stay unchanged.
+ */
+ command[0] = OP_READ_CONTINUOUS;
+ command[1] = (uint8_t)(addr >> 16);
+ command[2] = (uint8_t)(addr >> 8);
+ command[3] = (uint8_t)(addr >> 0);
+
+ /* plus 4 "don't care" bytes, command len: 4 + 4 "don't care" bytes */
+ status = spi_flash_read_common(spi_flash, command, 8, buf, len);
+
+ return status;
+}
+
+/*
+ * Write to the DataFlash device.
+ * to : Start offset in flash device
+ * len : Amount to write
+ * retlen : Amount of data actually written
+ * buf : Buffer containing the data
+ */
+int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len,
+ const void *buf)
+{
+ struct dataflash *dataflash;
+ struct spi_flash *spi_flash;
+ struct spi_slave *spi;
+ uint8_t *command;
+ unsigned int pageaddr, addr, to, writelen;
+ size_t remaining = len;
+ u_char *writebuf = (u_char *)buf;
+ int status = -EINVAL;
+
+ dataflash = dev->priv;
+ spi_flash = dataflash->flash;
+ spi = spi_flash->spi;
+
+ memset(dataflash->command, 0 , sizeof(dataflash->command));
+
+ debug("%s: write 0x%x..0x%x\n",
+ dev->name, (unsigned)offset, (unsigned)(offset + len));
+
+ command = dataflash->command;
+
+ pageaddr = ((unsigned)offset / spi_flash->page_size);
+ to = ((unsigned)offset % spi_flash->page_size);
+ if (to + len > spi_flash->page_size)
+ writelen = spi_flash->page_size - to;
+ else
+ writelen = len;
+
+ while (remaining > 0) {
+ debug("write @ %i:%i len=%i\n",
+ pageaddr, to, writelen);
+
+ /* REVISIT:
+ * (a) each page in a sector must be rewritten at least
+ * once every 10K sibling erase/program operations.
+ * (b) for pages that are already erased, we could
+ * use WRITE+MWRITE not PROGRAM for ~30% speedup.
+ * (c) WRITE to buffer could be done while waiting for
+ * a previous MWRITE/MWERASE to complete ...
+ * (d) error handling here seems to be mostly missing.
+ *
+ * Two persistent bits per page, plus a per-sector counter,
+ * could support (a) and (b) ... we might consider using
+ * the second half of sector zero, which is just one block,
+ * to track that state. (On AT91, that sector should also
+ * support boot-from-DataFlash.)
+ */
+
+ addr = pageaddr << dataflash->page_offset;
+
+ /* (1) Maybe transfer partial page to Buffer1 */
+ if (writelen != spi_flash->page_size) {
+ command[0] = OP_TRANSFER_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = 0;
+
+ debug("TRANSFER: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ status = spi_flash_write_common(spi_flash,
+ command, 4, NULL, 0);
+ if (status < 0)
+ return -EIO;
+
+ status = dataflash_waitready(spi);
+ if (status < 0)
+ return status;
+ }
+
+ /* (2) Program full page via Buffer1 */
+ addr += to;
+ command[0] = OP_PROGRAM_VIA_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = (addr & 0x000000FF);
+
+ debug("PROGRAM: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ status = spi_flash_write_common(spi_flash,
+ command, 4, writebuf, writelen);
+ if (status < 0)
+ return -EIO;
+
+ status = dataflash_waitready(spi);
+ if (status < 0)
+ return status;
+
+#ifdef CONFIG_SPI_DATAFLASH_WRITE_VERIFY
+
+ /* (3) Compare to Buffer1 */
+ addr = pageaddr << priv->page_offset;
+ command[0] = OP_COMPARE_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = 0;
+
+ debug("COMPARE: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ status = spi_flash_write_common(spi_flash,
+ command, 4, writebuf, writelen);
+ if (status < 0)
+ return -EIO;
+
+ status = dataflash_waitready(spi);
+
+ /* Check result of the compare operation */
+ if (status & (1 << 6)) {
+ printf("SPI DataFlash: write compare page %u, err %d\n",
+ pageaddr, status);
+ remaining = 0;
+ status = -EIO;
+ break;
+ } else {
+ status = 0;
+ }
+
+#endif /* CONFIG_MTD_DATAFLASH_WRITE_VERIFY */
+ remaining = remaining - writelen;
+ pageaddr++;
+ to = 0;
+ writebuf += writelen;
+
+ if (remaining > spi_flash->page_size)
+ writelen = spi_flash->page_size;
+ else
+ writelen = remaining;
+ }
+
+ return status;
+}
+
+/* ......................................................................... */
+
+/*
+ * Register DataFlash device with MTD subsystem.
+ */
+static int add_dataflash(struct dataflash *dataflash, char *name, int nr_pages,
+ int pagesize, int pageoffset, char revision)
+{
+ struct spi_flash *spi_flash;
+
+ spi_flash = dataflash->flash;
+
+ dataflash->page_offset = pageoffset;
+
+ spi_flash->name = name;
+ spi_flash->page_size = pagesize;
+ spi_flash->size = nr_pages * pagesize;
+ spi_flash->erase_size = pagesize;
+
+#ifndef CONFIG_SPL_BUILD
+ printf("SPI DataFlash: Detected %s with page size ", spi_flash->name);
+ print_size(spi_flash->page_size, ", erase size ");
+ print_size(spi_flash->erase_size, ", total ");
+ print_size(spi_flash->size, "");
+ printf("revision %c", revision);
+ puts("\n");
+#endif
+
+ return 0;
+}
+
+struct flash_info {
+ char *name;
+
+ /* JEDEC id has a high byte of zero plus three data bytes:
+ * the manufacturer id, then a two byte device id.
+ */
+ uint32_t jedec_id;
+
+ /* The size listed here is what works with OP_ERASE_PAGE. */
+ unsigned nr_pages;
+ uint16_t pagesize;
+ uint16_t pageoffset;
+
+ uint16_t flags;
+#define SUP_POW2PS 0x0002 /* supports 2^N byte pages */
+#define IS_POW2PS 0x0001 /* uses 2^N byte pages */
+};
+
+static struct flash_info dataflash_data[] = {
+ /*
+ * NOTE: chips with SUP_POW2PS (rev D and up) need two entries,
+ * one with IS_POW2PS and the other without. The entry with the
+ * non-2^N byte page size can't name exact chip revisions without
+ * losing backwards compatibility for cmdlinepart.
+ *
+ * These newer chips also support 128-byte security registers (with
+ * 64 bytes one-time-programmable) and software write-protection.
+ */
+ { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS},
+ { "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
+ { "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
+ { "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
+ { "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
+ { "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */
+
+ { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
+ { "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
+ { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
+};
+
+static struct flash_info *jedec_probe(struct spi_slave *spi, u8 *id)
+{
+ int tmp;
+ uint32_t jedec;
+ struct flash_info *info;
+ int status;
+
+ /* JEDEC also defines an optional "extended device information"
+ * string for after vendor-specific data, after the three bytes
+ * we use here. Supporting some chips might require using it.
+ *
+ * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
+ * That's not an error; only rev C and newer chips handle it, and
+ * only Atmel sells these chips.
+ */
+ if (id[0] != 0x1f)
+ return NULL;
+
+ jedec = id[0];
+ jedec = jedec << 8;
+ jedec |= id[1];
+ jedec = jedec << 8;
+ jedec |= id[2];
+
+ for (tmp = 0, info = dataflash_data;
+ tmp < ARRAY_SIZE(dataflash_data);
+ tmp++, info++) {
+ if (info->jedec_id == jedec) {
+ if (info->flags & SUP_POW2PS) {
+ status = dataflash_status(spi);
+ if (status < 0) {
+ debug("SPI DataFlash: status error %d\n",
+ status);
+ return NULL;
+ }
+ if (status & 0x1) {
+ if (info->flags & IS_POW2PS)
+ return info;
+ } else {
+ if (!(info->flags & IS_POW2PS))
+ return info;
+ }
+ } else {
+ return info;
+ }
+ }
+ }
+
+ /*
+ * Treat other chips as errors ... we won't know the right page
+ * size (it might be binary) even when we can tell which density
+ * class is involved (legacy chip id scheme).
+ */
+ printf("SPI DataFlash: Unsupported flash IDs: ");
+ printf("manuf %02x, jedec %04x, ext_jedec %04x\n",
+ id[0], jedec, id[3] << 8 | id[4]);
+ return NULL;
+}
+
+/*
+ * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
+ * or else the ID code embedded in the status bits:
+ *
+ * Device Density ID code #Pages PageSize Offset
+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
+ * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
+ */
+static int spi_dataflash_probe(struct udevice *dev)
+{
+ struct spi_slave *spi = dev_get_parentdata(dev);
+ struct spi_flash *spi_flash;
+ struct dataflash *dataflash;
+ struct flash_info *info;
+ u8 idcode[5];
+ int ret, status = 0;
+
+ spi_flash = dev->uclass_priv;
+ spi_flash->dev = dev;
+ spi_flash->spi = spi;
+ spi_flash->memory_map = spi->memory_map;
+ spi_flash->dual_flash = spi->option;
+
+ dataflash = dev->priv;
+ dataflash->flash = spi_flash;
+
+ ret = spi_claim_bus(spi);
+ if (ret)
+ return ret;
+
+ ret = spi_flash_cmd(spi, CMD_READ_ID, idcode, sizeof(idcode));
+ if (ret) {
+ printf("SPI DataFlash: Failed to get idcodes\n");
+ goto err_read_cmd;
+ }
+
+ /*
+ * Try to detect dataflash by JEDEC ID.
+ * If it succeeds we know we have either a C or D part.
+ * D will support power of 2 pagesize option.
+ * Both support the security register, though with different
+ * write procedures.
+ */
+ info = jedec_probe(spi, idcode);
+ if (info != NULL)
+ return add_dataflash(dataflash, info->name, info->nr_pages,
+ info->pagesize, info->pageoffset,
+ (info->flags & SUP_POW2PS) ? 'd' : 'c');
+
+ /*
+ * Older chips support only legacy commands, identifing
+ * capacity using bits in the status byte.
+ */
+ status = dataflash_status(spi);
+ if (status <= 0 || status == 0xff) {
+ debug("SPI DataFlash: read status error %d\n", status);
+ if (status == 0 || status == 0xff)
+ status = -ENODEV;
+ goto err_read_cmd;
+ }
+
+ /* if there's a device there, assume it's dataflash.
+ * board setup should have set spi->max_speed_max to
+ * match f(car) for continuous reads, mode 0 or 3.
+ */
+ switch (status & 0x3c) {
+ case 0x0c: /* 0 0 1 1 x x */
+ status = add_dataflash(dataflash, "AT45DB011B", 512, 264, 9, 0);
+ break;
+ case 0x14: /* 0 1 0 1 x x */
+ status = add_dataflash(dataflash,
+ "AT45DB021B", 1024, 264, 9, 0);
+ break;
+ case 0x1c: /* 0 1 1 1 x x */
+ status = add_dataflash(dataflash,
+ "AT45DB041x", 2048, 264, 9, 0);
+ break;
+ case 0x24: /* 1 0 0 1 x x */
+ status = add_dataflash(dataflash,
+ "AT45DB081B", 4096, 264, 9, 0);
+ break;
+ case 0x2c: /* 1 0 1 1 x x */
+ status = add_dataflash(dataflash,
+ "AT45DB161x", 4096, 528, 10, 0);
+ break;
+ case 0x34: /* 1 1 0 1 x x */
+ status = add_dataflash(dataflash,
+ "AT45DB321x", 8192, 528, 10, 0);
+ break;
+ case 0x38: /* 1 1 1 x x x */
+ case 0x3c:
+ status = add_dataflash(dataflash,
+ "AT45DB642x", 8192, 1056, 11, 0);
+ break;
+ /* obsolete AT45DB1282 not (yet?) supported */
+ default:
+ dev_info(&spi->dev, "unsupported device (%x)\n",
+ status & 0x3c);
+ status = -ENODEV;
+ goto err_read_cmd;
+ }
+
+ spi_release_bus(spi);
+
+ return 0;
+
+err_read_cmd:
+ spi_release_bus(spi);
+
+ return status;
+}
+
+static const struct dm_spi_flash_ops spi_dataflash_ops = {
+ .read = spi_dataflash_read,
+ .write = spi_dataflash_write,
+ .erase = spi_dataflash_erase,
+};
+
+static const struct udevice_id spi_dataflash_ids[] = {
+ { .compatible = "atmel,at45", },
+ { .compatible = "atmel,dataflash", },
+ { }
+};
+
+U_BOOT_DRIVER(spi_dataflash) = {
+ .name = "mtd_dataflash",
+ .id = UCLASS_SPI_FLASH,
+ .of_match = spi_dataflash_ids,
+ .probe = spi_dataflash_probe,
+ .priv_auto_alloc_size = sizeof(struct dataflash),
+ .ops = &spi_dataflash_ops,
+};
--
2.1.0.27.g96db324
More information about the U-Boot
mailing list