[U-Boot] [PATCH 3/3] sf: ti_qspi: Enable EDMA for reads in SPL

Tom Rini trini at konsulko.com
Wed Apr 22 16:25:46 CEST 2015


On Wed, Apr 22, 2015 at 04:45:05PM +0530, Jagan Teki wrote:
> On 15 July 2014 at 02:07, Tom Rini <trini at ti.com> wrote:
> > On Sat, Jul 12, 2014 at 06:42:31PM +0530, Jagan Teki wrote:
> >> On Sat, Jul 12, 2014 at 2:23 AM, Tom Rini <trini at ti.com> wrote:
> >> > From: Vinothkumar Rajendran <vinothr at ti.com>
> >> >
> >> > By default QSPI data through-put in memory mapped mode is ~2.4MB/sec @
> >> > 48MHz. Added edma memory copy functionality in spi flash driver to
> >> > improve the data through put to 5.1MB/Sec.
> > [snip]
> >> > +#include <asm/arch/edma.h>
> >> > +#include "../dma/ti_edma.h"
> >>
> >> This looks odd to me - header inclusion, as .h in drivers even.
> >
> > I could shove this under arch/arm/include/asm/ti-common I suppose.
> 
> Any changes in code logic or updates?

Since I posted? No, I was waiting for your reply :)

> >> >  /* ti qpsi register bit masks */
> >> >  #define QSPI_TIMEOUT                    2000000
> >> > @@ -340,3 +342,72 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
> >> >
> >> >         return 0;
> >> >  }
> >> > +
> >> > +#if defined(CONFIG_SPL_DMA_SUPPORT) && defined(CONFIG_TI_EDMA)
> >> > +void spi_flash_copy_mmap(void *data, void *offset, size_t len)
> >> > +{
> >> > +       struct edma_param_entry edma_param;
> >> > +       int           b_cnt_value = 1;
> >> > +       int           rem_bytes  = 0;
> >> > +       int           a_cnt_value = len;
> >> > +       unsigned int          addr      = (unsigned int) (data);
> >> > +       unsigned int          max_acnt  = 0x7FFFU;
> >> > +       unsigned int edma_ch_num = 1;
> >> > +
> >> > +       if (len > max_acnt)
> >> > +       {
> >> > +               b_cnt_value = (len / max_acnt);
> >> > +               rem_bytes  = (len % max_acnt);
> >> > +               a_cnt_value = max_acnt;
> >> > +       }
> >> > +
> >> > +       /* Compute QSPI address and size */
> >> > +       edma_param.opt      = 0;
> >> > +       edma_param.src_addr  = ((unsigned int) offset);
> >> > +       edma_param.dest_addr = addr;
> >> > +       edma_param.a_cnt     = a_cnt_value;
> >> > +       edma_param.b_cnt     = b_cnt_value;
> >> > +       edma_param.c_cnt     = 1;
> >> > +       edma_param.src_bidx  = a_cnt_value;
> >> > +       edma_param.dest_bidx = a_cnt_value;
> >> > +       edma_param.src_cidx  = 0;
> >> > +       edma_param.dest_cidx = 0;
> >> > +       edma_param.link_addr = 0xFFFF;
> >> > +       edma_param.opt     |=
> >> > +               (EDMA_TPCC_OPT_TCINTEN_MASK |
> >> > +                ((edma_ch_num <<
> >> > +                  EDMA_TPCC_OPT_TCC_SHIFT) &
> >> > +                 EDMA_TPCC_OPT_TCC_MASK) | EDMA_TPCC_OPT_SYNCDIM_MASK);
> >> > +
> >> > +       edma_set_param(edma_ch_num, &edma_param);
> >> > +       edma_enable_transfer(edma_ch_num);
> >> > +
> >> > +       while (!(edma_get_intr_status() & (1 << edma_ch_num))) ;
> >> > +       edma_clr_intr(edma_ch_num);
> >> > +       if (rem_bytes != 0)
> >> > +       {
> >> > +               /* Compute QSPI address and size */
> >> > +               edma_param.opt     = 0;
> >> > +               edma_param.src_addr =
> >> > +                       (b_cnt_value * max_acnt) + ((unsigned int) offset);
> >> > +               edma_param.dest_addr = (addr + (max_acnt * b_cnt_value));
> >> > +               edma_param.a_cnt     = rem_bytes;
> >> > +               edma_param.b_cnt     = 1;
> >> > +               edma_param.c_cnt     = 1;
> >> > +               edma_param.src_bidx  = rem_bytes;
> >> > +               edma_param.dest_bidx = rem_bytes;
> >> > +               edma_param.src_cidx  = 0;
> >> > +               edma_param.dest_cidx = 0;
> >> > +               edma_param.link_addr = 0xFFFF;
> >> > +               edma_param.opt     |=
> >> > +                       (EDMA_TPCC_OPT_TCINTEN_MASK |
> >> > +                        ((edma_ch_num << EDMA_TPCC_OPT_TCC_SHIFT) & EDMA_TPCC_OPT_TCC_MASK));
> >> > +               edma_set_param(edma_ch_num, &edma_param);
> >> > +               edma_enable_transfer(edma_ch_num);
> >> > +
> >> > +               while (!(edma_get_intr_status() & (1 << edma_ch_num))) ;
> >> > +               edma_clr_intr(edma_ch_num);
> >> > +       }
> >> > +       *((unsigned int *) offset) += len;
> >> > +}
> >> > +#endif
> >>
> >> I'm some how !OK with this memory or flash change in spi driver.
> >> Any better approach to move this - may be in DMA driver itself and
> >> picking up the
> >> memory attributes from sf layer.
> >>
> >> I'm not much clear about this now, but will come back again.
> >
> > Well, are you happy with how drivers/spi/mxs_spi.c works (search around
> > on mxs_dma)?  I can re-jigger things along those lines I suppose.
> 
> thanks!

So you're happy with how mxs_spi.c does DMA then?  I'll pencil in some
time to rework this code using that driver as a model then, thanks.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150422/5f7c831a/attachment.sig>


More information about the U-Boot mailing list