[U-Boot] [PATCH v2 1/4] sunxi: emac: port to phylib
Hans de Goede
hdegoede at redhat.com
Sat Apr 25 13:51:45 CEST 2015
This is a preparation-patch for adding device-model support to the emac
driver.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
drivers/net/sunxi_emac.c | 111 +++++++++++++++++++++++++----------------
include/configs/sunxi-common.h | 2 +
2 files changed, 71 insertions(+), 42 deletions(-)
diff --git a/drivers/net/sunxi_emac.c b/drivers/net/sunxi_emac.c
index 7b31f8c..b9fd1b8 100644
--- a/drivers/net/sunxi_emac.c
+++ b/drivers/net/sunxi_emac.c
@@ -156,9 +156,9 @@ struct sunxi_sramc_regs {
#define DMA_CPU_TRRESHOLD 2000
struct emac_eth_dev {
- u32 speed;
- u32 duplex;
- u32 phy_configured;
+ struct emac_regs *regs;
+ struct mii_dev *bus;
+ struct phy_device *phydev;
int link_printed;
};
@@ -195,11 +195,10 @@ static void emac_outblk_32bit(void *reg, void *data, int count)
}
/* Read a word from phyxcer */
-static int emac_phy_read(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short *value)
+static int emac_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
{
- struct eth_device *dev = eth_get_dev_by_name(devname);
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_eth_dev *priv = bus->priv;
+ struct emac_regs *regs = priv->regs;
/* issue the phy address and reg */
writel(addr << 8 | reg, ®s->mac_madr);
@@ -213,18 +212,16 @@ static int emac_phy_read(const char *devname, unsigned char addr,
/* push down the phy io line */
writel(0x0, ®s->mac_mcmd);
- /* and write data */
- *value = readl(®s->mac_mrdd);
-
- return 0;
+ /* And read data */
+ return readl(®s->mac_mrdd);
}
/* Write a word to phyxcer */
-static int emac_phy_write(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short value)
+static int emac_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
+ u16 value)
{
- struct eth_device *dev = eth_get_dev_by_name(devname);
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_eth_dev *priv = bus->priv;
+ struct emac_regs *regs = priv->regs;
/* issue the phy address and reg */
writel(addr << 8 | reg, ®s->mac_madr);
@@ -244,12 +241,44 @@ static int emac_phy_write(const char *devname, unsigned char addr,
return 0;
}
-static void emac_setup(struct eth_device *dev)
+static int sunxi_emac_init_phy(struct emac_eth_dev *priv, void *dev)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ int ret, mask = 0xffffffff;
+
+#ifdef CONFIG_PHY_ADDR
+ mask = 1 << CONFIG_PHY_ADDR;
+#endif
+
+ priv->bus = mdio_alloc();
+ if (!priv->bus) {
+ printf("Failed to allocate MDIO bus\n");
+ return -ENOMEM;
+ }
+
+ priv->bus->read = emac_mdio_read;
+ priv->bus->write = emac_mdio_write;
+ priv->bus->priv = priv;
+ strcpy(priv->bus->name, "emac");
+
+ ret = mdio_register(priv->bus);
+ if (ret)
+ return ret;
+
+ priv->phydev = phy_find_by_mask(priv->bus, mask,
+ PHY_INTERFACE_MODE_MII);
+ if (!priv->phydev)
+ return -ENODEV;
+
+ phy_connect_dev(priv->phydev, dev);
+ phy_config(priv->phydev);
+
+ return 0;
+}
+
+static void emac_setup(struct emac_eth_dev *priv)
+{
+ struct emac_regs *regs = priv->regs;
u32 reg_val;
- u16 phy_val;
- u32 duplex_flag;
/* Set up TX */
writel(EMAC_TX_SETUP, ®s->tx_mode);
@@ -262,12 +291,8 @@ static void emac_setup(struct eth_device *dev)
writel(EMAC_MAC_CTL0_SETUP, ®s->mac_ctl0);
/* Set MAC CTL1 */
- emac_phy_read(dev->name, 1, 0, &phy_val);
- debug("PHY SETUP, reg 0 value: %x\n", phy_val);
- duplex_flag = !!(phy_val & (1 << 8));
-
reg_val = 0;
- if (duplex_flag)
+ if (priv->phydev->duplex == DUPLEX_FULL)
reg_val = (0x1 << 0);
writel(EMAC_MAC_CTL1_SETUP | reg_val, ®s->mac_ctl1);
@@ -302,7 +327,7 @@ static int sunxi_emac_eth_init(struct eth_device *dev, bd_t *bd)
{
struct emac_regs *regs = (struct emac_regs *)dev->iobase;
struct emac_eth_dev *priv = dev->priv;
- u16 phy_reg;
+ int ret;
/* Init EMAC */
@@ -320,7 +345,7 @@ static int sunxi_emac_eth_init(struct eth_device *dev, bd_t *bd)
udelay(1);
/* Set up EMAC */
- emac_setup(dev);
+ emac_setup(priv);
writel(dev->enetaddr[0] << 16 | dev->enetaddr[1] << 8 |
dev->enetaddr[2], ®s->mac_a1);
@@ -332,29 +357,32 @@ static int sunxi_emac_eth_init(struct eth_device *dev, bd_t *bd)
emac_reset(dev);
/* PHY POWER UP */
- emac_phy_read(dev->name, 1, 0, &phy_reg);
- emac_phy_write(dev->name, 1, 0, phy_reg & (~(0x1 << 11)));
- mdelay(1);
-
- emac_phy_read(dev->name, 1, 0, &phy_reg);
-
- priv->speed = miiphy_speed(dev->name, 0);
- priv->duplex = miiphy_duplex(dev->name, 0);
+ ret = phy_startup(priv->phydev);
+ if (ret) {
+ printf("Could not initialize PHY %s\n",
+ priv->phydev->dev->name);
+ return ret;
+ }
/* Print link status only once */
if (!priv->link_printed) {
printf("ENET Speed is %d Mbps - %s duplex connection\n",
- priv->speed, (priv->duplex == HALF) ? "HALF" : "FULL");
+ priv->phydev->speed,
+ priv->phydev->duplex ? "FULL" : "HALF");
priv->link_printed = 1;
}
/* Set EMAC SPEED depend on PHY */
- clrsetbits_le32(®s->mac_supp, 1 << 8,
- ((phy_reg & (0x1 << 13)) >> 13) << 8);
+ if (priv->phydev->speed == SPEED_100)
+ setbits_le32(®s->mac_supp, 1 << 8);
+ else
+ clrbits_le32(®s->mac_supp, 1 << 8);
/* Set duplex depend on phy */
- clrsetbits_le32(®s->mac_ctl1, 1 << 0,
- ((phy_reg & (0x1 << 8)) >> 8) << 0);
+ if (priv->phydev->duplex == DUPLEX_FULL)
+ setbits_le32(®s->mac_ctl1, 1 << 0);
+ else
+ clrbits_le32(®s->mac_ctl1, 1 << 0);
/* Enable RX/TX */
setbits_le32(®s->ctl, 0x7);
@@ -505,6 +533,7 @@ int sunxi_emac_initialize(void)
/* Set MII clock */
clrsetbits_le32(®s->mac_mcfg, 0xf << 2, 0xd << 2);
+ priv->regs = regs;
dev->iobase = (int)regs;
dev->priv = priv;
dev->init = sunxi_emac_eth_init;
@@ -515,7 +544,5 @@ int sunxi_emac_initialize(void)
eth_register(dev);
- miiphy_register(dev->name, emac_phy_read, emac_phy_write);
-
- return 0;
+ return sunxi_emac_init_phy(priv, dev);
}
diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index f97e626..40c7f63 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -350,7 +350,9 @@ extern int soft_i2c_gpio_scl;
/* Ethernet support */
#ifdef CONFIG_SUNXI_EMAC
+#define CONFIG_PHY_ADDR 1
#define CONFIG_MII /* MII PHY management */
+#define CONFIG_PHYLIB
#endif
#ifdef CONFIG_SUNXI_GMAC
--
2.3.5
More information about the U-Boot
mailing list