[U-Boot] [PATCH v2 4/6] sunxi: axp: Move axp gpio code to a separate axpi-gpio driver
Hans de Goede
hdegoede at redhat.com
Sun Apr 26 11:51:25 CEST 2015
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.
This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.
Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.
The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/include/asm/arch-sunxi/gpio.h | 13 +++
board/sunxi/Kconfig | 6 ++
board/sunxi/board.c | 6 +-
configs/A13-OLinuXino_defconfig | 1 +
configs/Ainol_AW1_defconfig | 1 +
configs/Ampe_A76_defconfig | 1 +
configs/Astar_MID756_defconfig | 1 +
configs/Ippo_q8h_v1_2_a33_1024x600_defconfig | 1 +
configs/Ippo_q8h_v1_2_defconfig | 1 +
configs/Ippo_q8h_v5_defconfig | 1 +
configs/TZX-Q8-713B7_defconfig | 1 +
configs/UTOO_P66_defconfig | 1 +
configs/Yones_Toptech_BD1078_defconfig | 1 +
configs/forfun_q88db_defconfig | 1 +
configs/iNet_86VS_defconfig | 1 +
drivers/gpio/Makefile | 1 +
drivers/gpio/axp_gpio.c | 147 +++++++++++++++++++++++++++
drivers/gpio/sunxi_gpio.c | 17 ++--
drivers/power/axp209.c | 64 ------------
drivers/power/axp221.c | 64 ------------
include/axp152.h | 11 ++
include/axp209.h | 33 ++----
include/axp221.h | 21 ++--
23 files changed, 222 insertions(+), 173 deletions(-)
create mode 100644 drivers/gpio/axp_gpio.c
diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
index c9bfb4c..902e95b 100644
--- a/arch/arm/include/asm/arch-sunxi/gpio.h
+++ b/arch/arm/include/asm/arch-sunxi/gpio.h
@@ -217,4 +217,17 @@ int sunxi_name_to_gpio_bank(const char *name);
int sunxi_name_to_gpio(const char *name);
#define name_to_gpio(name) sunxi_name_to_gpio(name)
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
+int axp_gpio_init(void);
+#else
+static inline int axp_gpio_init(void) { return 0; }
+#endif
+
+struct udevice;
+
+int axp_gpio_direction_input(struct udevice *dev, unsigned offset);
+int axp_gpio_direction_output(struct udevice *dev, unsigned offset, int val);
+int axp_gpio_get_value(struct udevice *dev, unsigned offset);
+int axp_gpio_set_value(struct udevice *dev, unsigned offset, int val);
+
#endif /* _SUNXI_GPIO_H */
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index 3997637..a37b19e 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -328,6 +328,12 @@ config I2C4_ENABLE
See I2C0_ENABLE help text.
endif
+config AXP_GPIO
+ boolean "Enable support for gpio-s on axp PMICs"
+ default n
+ ---help---
+ Say Y here to enable support for the gpio pins of the axp PMIC ICs.
+
config VIDEO
boolean "Enable graphical uboot console on HDMI, LCD or VGA"
default y
diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index 6b93f92..ee66f98 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -80,7 +80,7 @@ DECLARE_GLOBAL_DATA_PTR;
/* add board specific code here */
int board_init(void)
{
- int id_pfr1;
+ int id_pfr1, ret;
gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100);
@@ -93,6 +93,10 @@ int board_init(void)
asm volatile("mcr p15, 0, %0, c14, c0, 0" : : "r"(24000000));
}
+ ret = axp_gpio_init();
+ if (ret)
+ return ret;
+
/* Uses dm gpio code so do this here and not in i2c_init_board() */
return soft_i2c_board_init();
}
diff --git a/configs/A13-OLinuXino_defconfig b/configs/A13-OLinuXino_defconfig
index 7fb466c..7b7b116 100644
--- a/configs/A13-OLinuXino_defconfig
+++ b/configs/A13-OLinuXino_defconfig
@@ -10,6 +10,7 @@ CONFIG_VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
diff --git a/configs/Ainol_AW1_defconfig b/configs/Ainol_AW1_defconfig
index a91a598..ff41444 100644
--- a/configs/Ainol_AW1_defconfig
+++ b/configs/Ainol_AW1_defconfig
@@ -10,6 +10,7 @@ CONFIG_MMC0_CD_PIN="PH1"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:40000,le:87,ri:112,up:38,lo:141,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_VIDEO_LCD_BL_EN="PH7"
diff --git a/configs/Ampe_A76_defconfig b/configs/Ampe_A76_defconfig
index 7bceb50..375cc68 100644
--- a/configs/Ampe_A76_defconfig
+++ b/configs/Ampe_A76_defconfig
@@ -9,6 +9,7 @@ CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:45,ri:82,up:22,lo:
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
diff --git a/configs/Astar_MID756_defconfig b/configs/Astar_MID756_defconfig
index ab55cbf..0072ab8 100644
--- a/configs/Astar_MID756_defconfig
+++ b/configs/Astar_MID756_defconfig
@@ -8,6 +8,7 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-astar-mid756"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
diff --git a/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig b/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
index a07c625..f54e2ee 100644
--- a/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
+++ b/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
@@ -6,6 +6,7 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-ippo-q8h-v1.2-lcd1024x600"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
diff --git a/configs/Ippo_q8h_v1_2_defconfig b/configs/Ippo_q8h_v1_2_defconfig
index 606472b..a6d58e7 100644
--- a/configs/Ippo_q8h_v1_2_defconfig
+++ b/configs/Ippo_q8h_v1_2_defconfig
@@ -4,6 +4,7 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-ippo-q8h-v1.2"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
diff --git a/configs/Ippo_q8h_v5_defconfig b/configs/Ippo_q8h_v5_defconfig
index f75737e..7f6e4ce 100644
--- a/configs/Ippo_q8h_v5_defconfig
+++ b/configs/Ippo_q8h_v5_defconfig
@@ -4,6 +4,7 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-ippo-q8h-v5"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
diff --git a/configs/TZX-Q8-713B7_defconfig b/configs/TZX-Q8-713B7_defconfig
index 1c1fbaa..3484a2f 100644
--- a/configs/TZX-Q8-713B7_defconfig
+++ b/configs/TZX-Q8-713B7_defconfig
@@ -9,6 +9,7 @@ CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
diff --git a/configs/UTOO_P66_defconfig b/configs/UTOO_P66_defconfig
index a449936..ee44b51 100644
--- a/configs/UTOO_P66_defconfig
+++ b/configs/UTOO_P66_defconfig
@@ -11,6 +11,7 @@ CONFIG_VIDEO_LCD_RESET="PG11"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
CONFIG_VIDEO_LCD_TL059WV5C0=y
+CONFIG_AXP_GPIO=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_MMC0_CD_PIN="PG0"
CONFIG_ARM=y
diff --git a/configs/Yones_Toptech_BD1078_defconfig b/configs/Yones_Toptech_BD1078_defconfig
index 6f6e89d..b675726 100644
--- a/configs/Yones_Toptech_BD1078_defconfig
+++ b/configs/Yones_Toptech_BD1078_defconfig
@@ -14,6 +14,7 @@ CONFIG_MMC1_PINS="PH"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:63000,le:32,ri:287,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_PANEL_LVDS=y
diff --git a/configs/forfun_q88db_defconfig b/configs/forfun_q88db_defconfig
index bafbed9..7722915 100644
--- a/configs/forfun_q88db_defconfig
+++ b/configs/forfun_q88db_defconfig
@@ -8,6 +8,7 @@ CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
diff --git a/configs/iNet_86VS_defconfig b/configs/iNet_86VS_defconfig
index 869a6d7..0646f9f 100644
--- a/configs/iNet_86VS_defconfig
+++ b/configs/iNet_86VS_defconfig
@@ -8,6 +8,7 @@ CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:45,ri:209,up:22,lo
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 8ca8b05..4a09302 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -7,6 +7,7 @@
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_DM_GPIO) += gpio-uclass.o
+obj-$(CONFIG_AXP_GPIO) += axp_gpio.o
endif
/* TODO(sjg at chromium.org): Only tegra supports driver model in SPL */
ifdef CONFIG_TEGRA_GPIO
diff --git a/drivers/gpio/axp_gpio.c b/drivers/gpio/axp_gpio.c
new file mode 100644
index 0000000..d04ec22
--- /dev/null
+++ b/drivers/gpio/axp_gpio.c
@@ -0,0 +1,147 @@
+/*
+ * (C) Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ *
+ * X-Powers AXP Power Management ICs gpio driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pmic_bus.h>
+#include <errno.h>
+
+#ifdef CONFIG_AXP152_POWER
+#include <axp152.h>
+#elif defined CONFIG_AXP209_POWER
+#include <axp209.h>
+#elif defined CONFIG_AXP221_POWER
+#include <axp221.h>
+#else
+#error Unknown AXP model
+#endif
+
+static u8 axp_get_gpio_ctrl_reg(unsigned pin)
+{
+ switch (pin) {
+ case 0: return AXP_GPIO0_CTRL;
+ case 1: return AXP_GPIO1_CTRL;
+#ifdef AXP_GPIO2_CTRL
+ case 2: return AXP_GPIO2_CTRL;
+#endif
+#ifdef AXP_GPIO3_CTRL
+ case 3: return AXP_GPIO3_CTRL;
+#endif
+ }
+ return 0;
+}
+
+int axp_gpio_direction_input(struct udevice *dev, unsigned pin)
+{
+ u8 reg;
+
+ switch (pin) {
+#ifndef CONFIG_AXP152_POWER /* NA on axp152 */
+ case SUNXI_GPIO_AXP0_VBUS_DETECT:
+ return 0;
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, AXP_GPIO_CTRL_INPUT);
+ }
+}
+
+int axp_gpio_direction_output(struct udevice *dev, unsigned pin, int val)
+{
+ __maybe_unused int ret;
+ u8 reg;
+
+ switch (pin) {
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ ret = pmic_bus_clrbits(AXP221_MISC_CTRL,
+ AXP221_MISC_CTRL_N_VBUSEN_FUNC);
+ if (ret)
+ return ret;
+
+ return axp_gpio_set_value(dev, pin, val);
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, val ? AXP_GPIO_CTRL_OUTPUT_HIGH :
+ AXP_GPIO_CTRL_OUTPUT_LOW);
+ }
+}
+
+int axp_gpio_get_value(struct udevice *dev, unsigned pin)
+{
+ u8 reg, val, mask;
+ int ret;
+
+ switch (pin) {
+#ifndef CONFIG_AXP152_POWER /* NA on axp152 */
+ case SUNXI_GPIO_AXP0_VBUS_DETECT:
+ ret = pmic_bus_read(AXP_POWER_STATUS, &val);
+ mask = AXP_POWER_STATUS_VBUS_PRESENT;
+ break;
+#endif
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ ret = pmic_bus_read(AXP221_VBUS_IPSOUT, &val);
+ mask = AXP221_VBUS_IPSOUT_DRIVEBUS;
+ break;
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ ret = pmic_bus_read(AXP_GPIO_STATE, &val);
+ mask = 1 << (pin + AXP_GPIO_STATE_OFFSET);
+ }
+ if (ret)
+ return ret;
+
+ return (val & mask) ? 1 : 0;
+}
+
+int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val)
+{
+ u8 reg;
+
+ switch (pin) {
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ if (val)
+ return pmic_bus_setbits(AXP221_VBUS_IPSOUT,
+ AXP221_VBUS_IPSOUT_DRIVEBUS);
+ else
+ return pmic_bus_clrbits(AXP221_VBUS_IPSOUT,
+ AXP221_VBUS_IPSOUT_DRIVEBUS);
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, val ? AXP_GPIO_CTRL_OUTPUT_HIGH :
+ AXP_GPIO_CTRL_OUTPUT_LOW);
+ }
+}
+
+int axp_gpio_init(void)
+{
+ int ret;
+
+ ret = pmic_bus_init();
+ if (ret)
+ return ret;
+
+ return 0;
+}
diff --git a/drivers/gpio/sunxi_gpio.c b/drivers/gpio/sunxi_gpio.c
index 0774b70..5a0b5e4 100644
--- a/drivers/gpio/sunxi_gpio.c
+++ b/drivers/gpio/sunxi_gpio.c
@@ -15,15 +15,10 @@
#include <errno.h>
#include <fdtdec.h>
#include <malloc.h>
+#include <asm/arch/gpio.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <dm/device-internal.h>
-#ifdef CONFIG_AXP209_POWER
-#include <axp209.h>
-#endif
-#ifdef CONFIG_AXP221_POWER
-#include <axp221.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -79,7 +74,7 @@ int gpio_free(unsigned gpio)
int gpio_direction_input(unsigned gpio)
{
-#ifdef AXP_GPIO
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
if (gpio >= SUNXI_GPIO_AXP0_START)
return axp_gpio_direction_input(NULL, gpio - SUNXI_GPIO_AXP0_START);
#endif
@@ -90,7 +85,7 @@ int gpio_direction_input(unsigned gpio)
int gpio_direction_output(unsigned gpio, int value)
{
-#ifdef AXP_GPIO
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
if (gpio >= SUNXI_GPIO_AXP0_START)
return axp_gpio_direction_output(NULL, gpio - SUNXI_GPIO_AXP0_START,
value);
@@ -102,7 +97,7 @@ int gpio_direction_output(unsigned gpio, int value)
int gpio_get_value(unsigned gpio)
{
-#ifdef AXP_GPIO
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
if (gpio >= SUNXI_GPIO_AXP0_START)
return axp_gpio_get_value(NULL, gpio - SUNXI_GPIO_AXP0_START);
#endif
@@ -111,7 +106,7 @@ int gpio_get_value(unsigned gpio)
int gpio_set_value(unsigned gpio, int value)
{
-#ifdef AXP_GPIO
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
if (gpio >= SUNXI_GPIO_AXP0_START)
return axp_gpio_set_value(NULL, gpio - SUNXI_GPIO_AXP0_START, value);
#endif
@@ -125,7 +120,7 @@ int sunxi_name_to_gpio(const char *name)
long pin;
char *eptr;
-#ifdef AXP_GPIO
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
if (strncasecmp(name, "AXP0-", 5) == 0) {
name += 5;
if (strcmp(name, "VBUS-DETECT") == 0)
diff --git a/drivers/power/axp209.c b/drivers/power/axp209.c
index 98c214f..5161bc1 100644
--- a/drivers/power/axp209.c
+++ b/drivers/power/axp209.c
@@ -155,67 +155,3 @@ int axp209_power_button(void)
return v & AXP209_IRQ5_PEK_DOWN;
}
-
-static u8 axp209_get_gpio_ctrl_reg(unsigned int pin)
-{
- switch (pin) {
- case 0: return AXP209_GPIO0_CTRL;
- case 1: return AXP209_GPIO1_CTRL;
- case 2: return AXP209_GPIO2_CTRL;
- case 3: return AXP209_GPIO3_CTRL;
- }
- return 0;
-}
-
-int axp_gpio_direction_input(struct udevice *dev, unsigned pin)
-{
- if (pin == SUNXI_GPIO_AXP0_VBUS_DETECT)
- return 0;
-
- u8 reg = axp209_get_gpio_ctrl_reg(pin);
- /* GPIO3 is "special" */
- u8 val = (pin == 3) ? AXP209_GPIO3_INPUT : AXP209_GPIO_INPUT;
-
- return axp209_write(reg, val);
-}
-
-int axp_gpio_direction_output(struct udevice *dev, unsigned pin, int val)
-{
- u8 reg = axp209_get_gpio_ctrl_reg(pin);
-
- if (val) {
- val = (pin == 3) ? AXP209_GPIO3_OUTPUT_HIGH :
- AXP209_GPIO_OUTPUT_HIGH;
- } else {
- val = (pin == 3) ? AXP209_GPIO3_OUTPUT_LOW :
- AXP209_GPIO_OUTPUT_LOW;
- }
-
- return axp209_write(reg, val);
-}
-
-int axp_gpio_get_value(struct udevice *dev, unsigned pin)
-{
- u8 val, mask;
- int rc;
-
- if (pin == SUNXI_GPIO_AXP0_VBUS_DETECT) {
- rc = axp209_read(AXP209_POWER_STATUS, &val);
- mask = AXP209_POWER_STATUS_VBUS_USABLE;
- } else if (pin == 3) {
- rc = axp209_read(AXP209_GPIO3_CTRL, &val);
- mask = 1;
- } else {
- rc = axp209_read(AXP209_GPIO_STATE, &val);
- mask = 1 << (pin + 4);
- }
- if (rc)
- return rc;
-
- return (val & mask) ? 1 : 0;
-}
-
-int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val)
-{
- return axp_gpio_direction_output(dev, pin, val);
-}
diff --git a/drivers/power/axp221.c b/drivers/power/axp221.c
index d49de86..7bbaec8 100644
--- a/drivers/power/axp221.c
+++ b/drivers/power/axp221.c
@@ -319,67 +319,3 @@ int axp221_get_sid(unsigned int *sid)
return 0;
}
-
-int axp_gpio_direction_input(struct udevice *dev, unsigned pin)
-{
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_DETECT:
- return 0;
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_direction_output(struct udevice *dev, unsigned pin, int val)
-{
- int ret;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_ENABLE:
- ret = axp221_clrbits(AXP221_MISC_CTRL,
- AXP221_MISC_CTRL_N_VBUSEN_FUNC);
- if (ret)
- return ret;
-
- return axp_gpio_set_value(dev, pin, val);
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_get_value(struct udevice *dev, unsigned pin)
-{
- int ret;
- u8 val;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_DETECT:
- ret = pmic_bus_read(AXP221_POWER_STATUS, &val);
- if (ret)
- return ret;
-
- return !!(val & AXP221_POWER_STATUS_VBUS_AVAIL);
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val)
-{
- int ret;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_ENABLE:
- if (val)
- ret = axp221_setbits(AXP221_VBUS_IPSOUT,
- AXP221_VBUS_IPSOUT_DRIVEBUS);
- else
- ret = axp221_clrbits(AXP221_VBUS_IPSOUT,
- AXP221_VBUS_IPSOUT_DRIVEBUS);
-
- if (ret)
- return ret;
- }
-
- return 0;
-}
diff --git a/include/axp152.h b/include/axp152.h
index 9d205f8..c3aef77 100644
--- a/include/axp152.h
+++ b/include/axp152.h
@@ -15,6 +15,17 @@ enum axp152_reg {
#define AXP152_POWEROFF (1 << 7)
+/* For axp_gpio.c */
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x91
+#define AXP_GPIO2_CTRL 0x92
+#define AXP_GPIO3_CTRL 0x93
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x97
+#define AXP_GPIO_STATE_OFFSET 0
+
int axp152_set_dcdc2(int mvolt);
int axp152_set_dcdc3(int mvolt);
int axp152_set_dcdc4(int mvolt);
diff --git a/include/axp209.h b/include/axp209.h
index fe4a169..6170202 100644
--- a/include/axp209.h
+++ b/include/axp209.h
@@ -4,8 +4,6 @@
* SPDX-License-Identifier: GPL-2.0+
*/
-struct udevice;
-
enum axp209_reg {
AXP209_POWER_STATUS = 0x00,
AXP209_CHIP_VERSION = 0x03,
@@ -20,11 +18,6 @@ enum axp209_reg {
AXP209_IRQ_ENABLE5 = 0x44,
AXP209_IRQ_STATUS5 = 0x4c,
AXP209_SHUTDOWN = 0x32,
- AXP209_GPIO0_CTRL = 0x90,
- AXP209_GPIO1_CTRL = 0x92,
- AXP209_GPIO2_CTRL = 0x93,
- AXP209_GPIO_STATE = 0x94,
- AXP209_GPIO3_CTRL = 0x95,
};
#define AXP209_POWER_STATUS_ON_BY_DC (1 << 0)
@@ -35,16 +28,17 @@ enum axp209_reg {
#define AXP209_POWEROFF (1 << 7)
-#define AXP209_GPIO_OUTPUT_LOW 0x00 /* Drive pin low */
-#define AXP209_GPIO_OUTPUT_HIGH 0x01 /* Drive pin high */
-#define AXP209_GPIO_INPUT 0x02 /* Float pin */
-
-/* GPIO3 is different from the others */
-#define AXP209_GPIO3_OUTPUT_LOW 0x00 /* Drive pin low, Output mode */
-#define AXP209_GPIO3_OUTPUT_HIGH 0x02 /* Float pin, Output mode */
-#define AXP209_GPIO3_INPUT 0x06 /* Float pin, Input mode */
-
-#define AXP_GPIO
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS 0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x92
+#define AXP_GPIO2_CTRL 0x93
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x94
+#define AXP_GPIO_STATE_OFFSET 4
extern int axp209_set_dcdc2(int mvolt);
extern int axp209_set_dcdc3(int mvolt);
@@ -54,8 +48,3 @@ extern int axp209_set_ldo4(int mvolt);
extern int axp209_init(void);
extern int axp209_poweron_by_dc(void);
extern int axp209_power_button(void);
-
-extern int axp_gpio_direction_input(struct udevice *dev, unsigned offset);
-extern int axp_gpio_direction_output(struct udevice *dev, unsigned offset, int val);
-extern int axp_gpio_get_value(struct udevice *dev, unsigned offset);
-extern int axp_gpio_set_value(struct udevice *dev, unsigned offset, int val);
diff --git a/include/axp221.h b/include/axp221.h
index f62f708..9c87162 100644
--- a/include/axp221.h
+++ b/include/axp221.h
@@ -6,12 +6,7 @@
* SPDX-License-Identifier: GPL-2.0+
*/
-struct udevice;
-
/* Page 0 addresses */
-#define AXP221_POWER_STATUS 0x00
-#define AXP221_POWER_STATUS_VBUS_AVAIL (1 << 5)
-#define AXP221_POWER_STATUS_VBUS_USABLE (1 << 4)
#define AXP221_CHIP_ID 0x03
#define AXP221_OUTPUT_CTRL1 0x10
#define AXP221_OUTPUT_CTRL1_DCDC0_EN (1 << 0)
@@ -57,7 +52,16 @@ struct udevice;
/* Page 1 addresses */
#define AXP221_SID 0x20
-#define AXP_GPIO
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS 0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x92
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x94
+#define AXP_GPIO_STATE_OFFSET 0
int axp221_set_dcdc1(unsigned int mvolt);
int axp221_set_dcdc2(unsigned int mvolt);
@@ -74,8 +78,3 @@ int axp221_set_aldo3(unsigned int mvolt);
int axp221_set_eldo(int eldo_num, unsigned int mvolt);
int axp221_init(void);
int axp221_get_sid(unsigned int *sid);
-
-int axp_gpio_direction_input(struct udevice *dev, unsigned offset);
-int axp_gpio_direction_output(struct udevice *dev, unsigned offset, int val);
-int axp_gpio_get_value(struct udevice *dev, unsigned offset);
-int axp_gpio_set_value(struct udevice *dev, unsigned offset, int val);
--
2.3.5
More information about the U-Boot
mailing list