[U-Boot] [PATCH] powerpc/mpc85xx: Add board support for ucp1020
Oleksandr G Zhadan
oleks at arcturusnetworks.com
Wed Apr 29 22:57:39 CEST 2015
New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/
Signed-off-by: Michael Durrant <mdurrant at arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks at arcturusnetworks.com>
Series-version: 2
Series-changes: 2
WARNINGs: line over 80 characters are fixed
---
arch/powerpc/cpu/mpc85xx/Kconfig | 4 +
board/Arcturus/ucp1020/Kconfig | 44 ++
board/Arcturus/ucp1020/MAINTAINERS | 7 +
board/Arcturus/ucp1020/Makefile | 33 ++
board/Arcturus/ucp1020/README | 54 ++
board/Arcturus/ucp1020/cmd_arc.c | 231 ++++++++
board/Arcturus/ucp1020/ddr.c | 161 ++++++
board/Arcturus/ucp1020/law.c | 25 +
board/Arcturus/ucp1020/spl.c | 126 +++++
board/Arcturus/ucp1020/spl_minimal.c | 67 +++
board/Arcturus/ucp1020/tlb.c | 101 ++++
board/Arcturus/ucp1020/ucp1020.c | 363 ++++++++++++
board/Arcturus/ucp1020/ucp1020.h | 44 ++
configs/UCP1020_SPIFLASH_defconfig | 6 +
configs/UCP1020_defconfig | 5 +
include/configs/UCP1020.h | 1027 ++++++++++++++++++++++++++++++++++
16 files changed, 2298 insertions(+)
create mode 100644 board/Arcturus/ucp1020/Kconfig
create mode 100644 board/Arcturus/ucp1020/MAINTAINERS
create mode 100644 board/Arcturus/ucp1020/Makefile
create mode 100644 board/Arcturus/ucp1020/README
create mode 100644 board/Arcturus/ucp1020/cmd_arc.c
create mode 100644 board/Arcturus/ucp1020/ddr.c
create mode 100644 board/Arcturus/ucp1020/law.c
create mode 100644 board/Arcturus/ucp1020/spl.c
create mode 100644 board/Arcturus/ucp1020/spl_minimal.c
create mode 100644 board/Arcturus/ucp1020/tlb.c
create mode 100644 board/Arcturus/ucp1020/ucp1020.c
create mode 100644 board/Arcturus/ucp1020/ucp1020.h
create mode 100644 configs/UCP1020_SPIFLASH_defconfig
create mode 100644 configs/UCP1020_defconfig
create mode 100644 include/configs/UCP1020.h
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index adb5bd3..e481ab4 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -153,6 +153,9 @@ config TARGET_XPEDITE537X
config TARGET_XPEDITE550X
bool "Support xpedite550x"
+config TARGET_UCP1020
+ bool "Support uCP1020"
+
endchoice
source "board/freescale/b4860qds/Kconfig"
@@ -194,5 +197,6 @@ source "board/stx/stxssa/Kconfig"
source "board/xes/xpedite520x/Kconfig"
source "board/xes/xpedite537x/Kconfig"
source "board/xes/xpedite550x/Kconfig"
+source "board/Arcturus/ucp1020/Kconfig"
endmenu
diff --git a/board/Arcturus/ucp1020/Kconfig b/board/Arcturus/ucp1020/Kconfig
new file mode 100644
index 0000000..feca03a
--- /dev/null
+++ b/board/Arcturus/ucp1020/Kconfig
@@ -0,0 +1,44 @@
+if TARGET_UCP1020
+
+config SYS_BOARD
+ string
+ default "ucp1020"
+
+config SYS_VENDOR
+ string
+ default "Arcturus"
+
+config SYS_CONFIG_NAME
+ string
+ default "UCP1020"
+
+config SPI_FLASH
+ bool
+ default y
+
+config SPI_PCI
+ bool
+ default y
+
+choice
+ prompt "Target image select"
+
+config TARGET_UCP1020_NOR
+ bool "NOR flash u-boot image"
+
+config TARGET_UCP1020_SPIFLASH
+ bool "SPI flash u-boot image"
+
+endchoice
+
+if TARGET_UCP1020_SPIFLASH
+config UCBOOT
+ bool
+ default y
+
+config SPIFLASH
+ bool
+ default y
+endif
+
+endif
diff --git a/board/Arcturus/ucp1020/MAINTAINERS b/board/Arcturus/ucp1020/MAINTAINERS
new file mode 100644
index 0000000..e4a4718
--- /dev/null
+++ b/board/Arcturus/ucp1020/MAINTAINERS
@@ -0,0 +1,7 @@
+UCP1020 BOARD
+M: Oleksandr Zhadan and Michael Durrant <arcsupport at arcturusnetworks.com>
+S: Maintained
+F: board/Arcturus/ucp1020/
+F: include/configs/UCP1020.h
+F: configs/UCP1020_defconfig
+F: configs/UCP1020_SPIFLASH_defconfig
diff --git a/board/Arcturus/ucp1020/Makefile b/board/Arcturus/ucp1020/Makefile
new file mode 100644
index 0000000..35c88b9
--- /dev/null
+++ b/board/Arcturus/ucp1020/Makefile
@@ -0,0 +1,33 @@
+#
+# Copyright 2013-2015 Arcturus Networks, Inc.
+# based on board/freescale/p1_p2_rdb_pc/Makefile
+# original copyright follows:
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+obj-y += spl_minimal.o tlb.o law.o
+
+else
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
+
+obj-y += ucp1020.o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
+obj-y += cmd_arc.o
+
+endif
diff --git a/board/Arcturus/ucp1020/README b/board/Arcturus/ucp1020/README
new file mode 100644
index 0000000..555c4ef
--- /dev/null
+++ b/board/Arcturus/ucp1020/README
@@ -0,0 +1,54 @@
+The uCP1020 product family (ucp1020) is an Arcturus Networks Inc. System on Modules
+product featuring a Freescale P1020 CPU, optionally populated with 1, 2 or 3 Gig-Ethernet PHYs,
+DDR3, NOR Flash, eMMC NAND Flash and/or SPI Flash.
+
+Information on the generic product family can be found here:
+ http://www.arcturusnetworks.com/products/ucp1020
+
+The UCP1020 several configurable options
+========================================
+
+- the selection of populated phy(s):
+ KSZ9031 (current default for eTSEC 1 and 3)
+
+- the selection of boot location:
+ SPI Flash or NOR flash
+
+The UCP1020 includes 2 default configurations
+=============================================
+NOR boot image:
+ configs/UCP1020_defconfig
+SPI boot image:
+ configs/UCP1020_SPIFLASH_defconfig
+
+The UCP1020 adds an additional command in cmd_arc.c to access and program
+SPI resident factory defaults for serial number, and 1, 2 or 3 Ethernet
+HW Addresses.
+
+
+Build example
+=============
+
+make distclean
+make UCP1020_defconfig
+make
+
+Default Scripts
+===============
+A default upgrade scripts is included in the default environment variable example:
+
+B$ run tftpflash
+
+Dual Environment
+================
+
+This build enables dual / failover environment environment.
+
+NOR Flash Partition declarations and scripts
+============================================
+Several scripts are available to allow TFTP of images and programming directly
+into defined NOR flash partitions. Examples:
+
+B$ run program0
+B$ run program1
+B$ run program2
diff --git a/board/Arcturus/ucp1020/cmd_arc.c b/board/Arcturus/ucp1020/cmd_arc.c
new file mode 100644
index 0000000..fa6b485
--- /dev/null
+++ b/board/Arcturus/ucp1020/cmd_arc.c
@@ -0,0 +1,231 @@
+/*
+ * Command for accessing Arcturus factory environment.
+ *
+ * Copyright 2013-2015 Arcturus Networks Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * by Oleksandr G Zhadan et al.
+ *
+ * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause
+ *
+ */
+
+#include <common.h>
+#include <div64.h>
+#include <malloc.h>
+#include <spi_flash.h>
+
+#include <asm/io.h>
+
+#ifndef CONFIG_SF_DEFAULT_SPEED
+# define CONFIG_SF_DEFAULT_SPEED 1000000
+#endif
+#ifndef CONFIG_SF_DEFAULT_MODE
+# define CONFIG_SF_DEFAULT_MODE SPI_MODE0
+#endif
+#ifndef CONFIG_SF_DEFAULT_CS
+# define CONFIG_SF_DEFAULT_CS 0
+#endif
+#ifndef CONFIG_SF_DEFAULT_BUS
+# define CONFIG_SF_DEFAULT_BUS 0
+#endif
+
+#define MAX_SERIAL_SIZE 15
+#define MAX_HWADDR_SIZE 17
+
+#define FIRM_ADDR1 (0x200 - sizeof(smac))
+#define FIRM_ADDR2 (0x400 - sizeof(smac))
+#define FIRM_ADDR3 (CONFIG_ENV_SECT_SIZE + 0x200 - sizeof(smac))
+#define FIRM_ADDR4 (CONFIG_ENV_SECT_SIZE + 0x400 - sizeof(smac))
+
+static struct spi_flash *flash;
+char smac[4][18];
+
+static int ishwaddr(char *hwaddr)
+{
+ if (strlen(hwaddr) == MAX_HWADDR_SIZE)
+ if (hwaddr[2] == ':' &&
+ hwaddr[5] == ':' &&
+ hwaddr[8] == ':' &&
+ hwaddr[11] == ':' &&
+ hwaddr[14] == ':')
+ return 0;
+ return -1;
+}
+
+static int set_arc_product(int argc, char *const argv[])
+{
+ int err = 0;
+ char *mystrerr = "ERROR: Failed to save factory info in spi location";
+
+ if (argc != 5)
+ return -1;
+
+ /* Check serial number */
+ if (strlen(argv[1]) != MAX_SERIAL_SIZE)
+ return -1;
+
+ /* Check HWaddrs */
+ if (ishwaddr(argv[2]) || ishwaddr(argv[3]) || ishwaddr(argv[4]))
+ return -1;
+
+ strcpy(smac[3], argv[1]);
+ strcpy(smac[2], argv[2]);
+ strcpy(smac[1], argv[3]);
+ strcpy(smac[0], argv[4]);
+
+ flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
+ CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+
+ /*
+ * Save factory defaults
+ */
+
+ if (spi_flash_write(flash, FIRM_ADDR1, sizeof(smac), smac)) {
+ printf("%s: %s [1]\n", __func__, mystrerr);
+ err++;
+ }
+ if (spi_flash_write(flash, FIRM_ADDR2, sizeof(smac), smac)) {
+ printf("%s: %s [2]\n", __func__, mystrerr);
+ err++;
+ }
+
+ if (spi_flash_write(flash, FIRM_ADDR3, sizeof(smac), smac)) {
+ printf("%s: %s [3]\n", __func__, mystrerr);
+ err++;
+ }
+
+ if (spi_flash_write(flash, FIRM_ADDR4, sizeof(smac), smac)) {
+ printf("%s: %s [4]\n", __func__, mystrerr);
+ err++;
+ }
+
+ if (err == 4) {
+ printf("%s: %s [ALL]\n", __func__, mystrerr);
+ return -2;
+ }
+
+ return 0;
+}
+
+int get_arc_info(void)
+{
+ int location = 1;
+ char *myerr = "ERROR: Failed to read all 4 factory info spi locations";
+
+ flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
+ CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+
+ if (spi_flash_read(flash, FIRM_ADDR1, sizeof(smac), smac)) {
+ location++;
+ if (spi_flash_read(flash, FIRM_ADDR2, sizeof(smac), smac)) {
+ location++;
+ if (spi_flash_read(flash, FIRM_ADDR3, sizeof(smac),
+ smac)) {
+ location++;
+ if (spi_flash_read(flash, FIRM_ADDR4,
+ sizeof(smac), smac)) {
+ printf("%s: %s\n", __func__, myerr);
+ return -2;
+ }
+ }
+ }
+ }
+ if (smac[3][0] != 0) {
+ if (location > 1)
+ printf("Using region %d\n", location);
+ printf("SERIAL: ");
+ if (smac[3][0] == 0xFF) {
+ printf("\t<not found>\n");
+ } else {
+ printf("\t%s\n", smac[3]);
+ setenv("SERIAL", smac[3]);
+ }
+ }
+
+ if (strcmp(smac[2], "00:00:00:00:00:00") == 0)
+ return 0;
+
+ printf("HWADDR0:");
+ if (smac[2][0] == 0xFF) {
+ printf("\t<not found>\n");
+ } else {
+ char *ret = getenv("ethaddr");
+
+ if (strcmp(ret, __stringify(CONFIG_ETHADDR)) == 0) {
+ setenv("ethaddr", smac[2]);
+ printf("\t%s (factory)\n", smac[2]);
+ } else {
+ printf("\t%s\n", ret);
+ }
+ }
+
+ if (strcmp(smac[1], "00:00:00:00:00:00") == 0) {
+ setenv("eth1addr", smac[2]);
+ setenv("eth2addr", smac[2]);
+ return 0;
+ }
+
+ printf("HWADDR1:");
+ if (smac[1][0] == 0xFF) {
+ printf("\t<not found>\n");
+ } else {
+ char *ret = getenv("eth1addr");
+
+ if (strcmp(ret, __stringify(CONFIG_ETH1ADDR)) == 0) {
+ setenv("eth1addr", smac[1]);
+ printf("\t%s (factory)\n", smac[1]);
+ } else {
+ printf("\t%s\n", ret);
+ }
+ }
+
+ if (strcmp(smac[0], "00:00:00:00:00:00") == 0) {
+ setenv("eth2addr", smac[1]);
+ return 0;
+ }
+
+ printf("HWADDR2:");
+ if (smac[0][0] == 0xFF) {
+ printf("\t<not found>\n");
+ } else {
+ char *ret = getenv("eth2addr");
+
+ if (strcmp(ret, __stringify(CONFIG_ETH2ADDR)) == 0) {
+ setenv("eth2addr", smac[0]);
+ printf("\t%s (factory)\n", smac[0]);
+ } else {
+ printf("\t%s\n", ret);
+ }
+ }
+
+ return 0;
+}
+
+static int do_arc_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ const char *cmd;
+ int ret = -1;
+
+ cmd = argv[1];
+ --argc;
+ ++argv;
+
+ if (strcmp(cmd, "product") == 0) {
+ ret = set_arc_product(argc, argv);
+ goto done;
+ }
+ if (strcmp(cmd, "info") == 0) {
+ ret = get_arc_info();
+ goto done;
+ }
+done:
+ if (ret == -1)
+ return CMD_RET_USAGE;
+
+ return ret;
+}
+
+U_BOOT_CMD(arc, 6, 1, do_arc_cmd,
+ "Arcturus product command sub-system",
+ "product serial hwaddr0 hwaddr1 hwaddr2 - save Arcturus factory env\n"
+ "info - show Arcturus factory env\n\n");
diff --git a/board/Arcturus/ucp1020/ddr.c b/board/Arcturus/ucp1020/ddr.c
new file mode 100644
index 0000000..42fbae0
--- /dev/null
+++ b/board/Arcturus/ucp1020/ddr.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/spl.c
+ * original copyright follows:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+#if defined(CONFIG_UCP1020) || defined(CONFIG_UCP1020T1)
+/*
+ * Micron MT41J128M16HA-15E
+ * */
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 1,
+ .rank_density = 536870912u,
+ .capacity = 536870912u,
+ .primary_sdram_width = 32,
+ .ec_sdram_width = 8,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 14,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 2,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 1650,
+ .caslat_x = 0x7e << 4, /* 5,6,7,8,9,10 */
+ .taa_ps = 14050,
+ .twr_ps = 15000,
+ .trcd_ps = 13500,
+ .trrd_ps = 75000,
+ .trp_ps = 13500,
+ .tras_ps = 40000,
+ .trc_ps = 49500,
+ .trfc_ps = 160000,
+ .twtr_ps = 75000,
+ .trtp_ps = 75000,
+ .refresh_rate_ps = 7800000,
+ .tfaw_ps = 30000,
+};
+
+#else
+#error Missing raw timing data for this board
+#endif
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if ((controller_number == 0) && (dimm_number == 0)) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+#endif /* CONFIG_SYS_DDR_RAW_TIMING */
+
+#ifdef CONFIG_SYS_DDR_CS0_BNDS
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+ sys_info_t sysinfo;
+ char buf[32];
+ size_t ddr_size;
+ fsl_ddr_cfg_regs_t ddr_cfg_regs = {
+ .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+ .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+ .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
+ .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+ .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+ .cs[1].config_2 = CONFIG_SYS_DDR_CS1_CONFIG_2,
+#endif
+ .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3,
+ .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0,
+ .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1,
+ .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2,
+ .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+ .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+ .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1,
+ .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2,
+ .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+ .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL,
+ .ddr_data_init = CONFIG_SYS_DDR_DATA_INIT,
+ .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL,
+ .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+ .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+ .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+ .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+ .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+ .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
+ .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+ .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+ .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+ };
+
+ get_sys_info(&sysinfo);
+ printf("Configuring DDR for %s MT/s data rate\n",
+ strmhz(buf, sysinfo.freq_ddrbus));
+
+ ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
+ fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
+
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+ ddr_size, LAW_TRGT_IF_DDR_1) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ };
+
+ return ddr_size;
+}
+#endif
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ int i;
+
+ popts->clk_adjust = 6;
+ popts->cpo_override = 0x1f;
+ popts->write_data_delay = 2;
+ popts->half_strength_driver_enable = 1;
+ /* Write leveling override */
+ popts->wrlvl_en = 1;
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x8;
+ popts->trwt_override = 1;
+ popts->trwt = 0;
+
+ if (pdimm->primary_sdram_width == 64)
+ popts->data_bus_width = 0;
+ else if (pdimm->primary_sdram_width == 32)
+ popts->data_bus_width = 1;
+ else
+ printf("Error in DDR bus width configuration!\n");
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+ popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+ }
+}
diff --git a/board/Arcturus/ucp1020/law.c b/board/Arcturus/ucp1020/law.c
new file mode 100644
index 0000000..7d40905
--- /dev/null
+++ b/board/Arcturus/ucp1020/law.c
@@ -0,0 +1,25 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/spl.c
+ * original copyright follows:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifdef CONFIG_VSC7385_ENET
+ SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#endif
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/Arcturus/ucp1020/spl.c b/board/Arcturus/ucp1020/spl.c
new file mode 100644
index 0000000..236b0d0
--- /dev/null
+++ b/board/Arcturus/ucp1020/spl.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/spl.c
+ * original copyright follows:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <nand.h>
+#include <i2c.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const u32 sysclk_tbl[] = {
+ 66666000, 7499900, 83332500, 8999900,
+ 99999000, 11111000, 12499800, 13333200
+};
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, bus_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ console_init_f();
+
+ /* Set pmuxcr to allow both i2c1 and i2c2 */
+ setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+ setbits_be32(&gur->pmuxcr,
+ in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+ /* Read back the register to synchronize the write. */
+ in_be32(&gur->pmuxcr);
+
+#ifdef CONFIG_SPL_SPI_BOOT
+ clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+#endif
+
+ /* initialize selected port with appropriate baud rate */
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+ gd->bus_clk = bus_clk;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI Flash boot...\n");
+#endif
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+ bd_t *bd;
+
+ memset(gd, 0, sizeof(gd_t));
+ bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifndef CONFIG_SPL_NAND_BOOT
+ env_init();
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+ /* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+#else
+ env_relocate();
+#endif
+
+#ifdef CONFIG_SYS_I2C
+ i2c_init_all();
+#else
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+#endif
+
+ gd->ram_size = initdram(0);
+#ifdef CONFIG_SPL_NAND_BOOT
+ puts("Tertiary program loader running in sram...");
+#else
+ puts("Second program loader running in sram...\n");
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/Arcturus/ucp1020/spl_minimal.c b/board/Arcturus/ucp1020/spl_minimal.c
new file mode 100644
index 0000000..5bdefb8
--- /dev/null
+++ b/board/Arcturus/ucp1020/spl_minimal.c
@@ -0,0 +1,67 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/spl_minimal.c
+ * original copyright follows:
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <linux/compiler.h>
+#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+ set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
+#endif
+
+ /* initialize selected port with appropriate baud rate */
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ gd->bus_clk / 16 / CONFIG_BAUDRATE);
+
+ puts("\nNAND boot... ");
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ puts("\nSecond program loader running in sram...");
+ nand_boot();
+}
+
+void putc(char c)
+{
+ if (c == '\n')
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+ while (*str)
+ putc(*str++);
+}
diff --git a/board/Arcturus/ucp1020/tlb.c b/board/Arcturus/ucp1020/tlb.c
new file mode 100644
index 0000000..fd7134f
--- /dev/null
+++ b/board/Arcturus/ucp1020/tlb.c
@@ -0,0 +1,101 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on board/freescale/p1_p2_rdb_pc/tlb.c
+ * original copyright follows:
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+ /* W**G* - Flash/promjet, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX | MAS3_SR, MAS2_W | MAS2_G,
+ 0, 2, BOOKE_PAGESZ_64M, 1),
+
+#ifdef CONFIG_PCI
+ /* *I*G* - PCI memory 1.5G */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI I/O effective: 192K */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#ifdef CONFIG_VSC7385_ENET
+ /* *I*G - VSC7385 Switch */
+ SET_TLB_ENTRY(1, CONFIG_SYS_VSC7385_BASE, CONFIG_SYS_VSC7385_BASE_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 5, BOOKE_PAGESZ_1M, 1),
+#endif
+#endif /* not SPL */
+
+#ifdef CONFIG_SYS_NAND_BASE
+ /* *I*G - NAND */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 7, BOOKE_PAGESZ_1M, 1),
+#endif
+
+#if defined(CONFIG_SYS_RAMBOOT) || \
+ (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
+ /* *I*G - eSDHC/eSPI/NAND boot */
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 8, BOOKE_PAGESZ_1G, 1),
+
+#endif /* RAMBOOT/SPL */
+
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+ /* *I*G - L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#if CONFIG_SYS_L2_SIZE >= (256 << 10)
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+ CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 12, BOOKE_PAGESZ_256K, 1)
+#endif
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/Arcturus/ucp1020/ucp1020.c b/board/Arcturus/ucp1020/ucp1020.c
new file mode 100644
index 0000000..0fc2bac
--- /dev/null
+++ b/board/Arcturus/ucp1020/ucp1020.c
@@ -0,0 +1,363 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * by Oleksandr G Zhadan et al.
+ * based on board/freescale/p1_p2_rdb_pc/spl.c
+ * original copyright follows:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <hwconfig.h>
+#include <pci.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <ioports.h>
+#include <netdev.h>
+#include <micrel.h>
+#include <spi_flash.h>
+#include <mmc.h>
+#include <linux/ctype.h>
+#include <asm/fsl_serdes.h>
+#include <asm/gpio.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_lbc.h>
+#include <asm/mp.h>
+#include "ucp1020.h"
+
+void spi_set_speed(struct spi_slave *slave, uint hz)
+{
+ /* TO DO: It's actially have to be in spi/ */
+}
+
+/*
+ * To be compatible with cmd_gpio
+ */
+int name_to_gpio(const char *name)
+{
+ int gpio = 31 - simple_strtoul(name, NULL, 10);
+
+ if (gpio < 16)
+ gpio = -1;
+
+ return gpio;
+}
+
+void board_gpio_init(void)
+{
+ int i;
+ char envname[8], *val;
+
+ for (i = 0; i < GPIO_MAX_NUM; i++) {
+ sprintf(envname, "GPIO%d", i);
+ val = getenv(envname);
+ if (val) {
+ char direction = toupper(val[0]);
+ char level = toupper(val[1]);
+
+ if (direction == 'I') {
+ gpio_direction_input(i);
+ } else {
+ if (direction == 'O') {
+ if (level == '1')
+ gpio_direction_output(i, 1);
+ else
+ gpio_direction_output(i, 0);
+ }
+ }
+ }
+ }
+
+ val = getenv("PCIE_OFF");
+ if (val) {
+ gpio_direction_input(GPIO_PCIE1_EN);
+ gpio_direction_input(GPIO_PCIE2_EN);
+ } else {
+ gpio_direction_output(GPIO_PCIE1_EN, 1);
+ gpio_direction_output(GPIO_PCIE2_EN, 1);
+ }
+
+ val = getenv("SDHC_CDWP_OFF");
+ if (!val) {
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ setbits_be32(&gur->pmuxcr,
+ (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP));
+ }
+}
+
+int board_early_init_f(void)
+{
+ return 0; /* Just in case. Could be disable in config file */
+}
+
+int checkboard(void)
+{
+ printf("Board: %s\n", CONFIG_BOARDNAME_LOCAL);
+ board_gpio_init();
+ printf("SD/MMC: 4-bit Mode\n");
+
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, /* perms, wimge */
+ 0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+#if defined(CONFIG_PHY_MICREL_KSZ9021)
+ int regval;
+ static int cnt;
+
+ if (cnt++ == 0)
+ printf("PHYs address [");
+
+ if (phydev->addr == TSEC1_PHY_ADDR || phydev->addr == TSEC3_PHY_ADDR) {
+ regval =
+ ksz9021_phy_extended_read(phydev,
+ MII_KSZ9021_EXT_STRAP_STATUS);
+ /*
+ * min rx data delay
+ */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+ 0x6666);
+ /*
+ * max rx/tx clock delay, min rx/tx control
+ */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+ 0xf6f6);
+ printf("0x%x", (regval & 0x1f));
+ } else {
+ printf("0x%x", (TSEC2_PHY_ADDR & 0x1f));
+ }
+ if (cnt == 3)
+ printf("] ");
+ else
+ printf(",");
+#endif
+
+#if defined(CONFIG_PHY_MICREL_KSZ9031_DEBUG)
+ regval = ksz9031_phy_extended_read(phydev, 2, 0x01, 0x4000);
+ if (regval >= 0)
+ printf(" (ADDR 0x%x) ", regval & 0x1f);
+#endif
+
+ return 0;
+}
+
+int last_stage_init(void)
+{
+ static char newkernelargs[256];
+ static u8 id1[16];
+ static u8 id2;
+ struct mmc *mmc;
+ char *sval, *kval;
+
+ if (i2c_read(CONFIG_SYS_I2C_IDT6V49205B, 7, 1, &id1[0], 2) < 0) {
+ printf("Error reading i2c IDT6V49205B information!\n");
+ } else {
+ printf("IDT6V49205B(0x%02x): ready\n", id1[1]);
+ i2c_read(CONFIG_SYS_I2C_IDT6V49205B, 4, 1, &id1[0], 2);
+ if (!(id1[1] & 0x02)) {
+ id1[1] |= 0x02;
+ i2c_write(CONFIG_SYS_I2C_IDT6V49205B, 4, 1, &id1[0], 2);
+ asm("nop; nop");
+ }
+ }
+
+ if (i2c_read(CONFIG_SYS_I2C_NCT72_ADDR, 0xFE, 1, &id2, 1) < 0)
+ printf("Error reading i2c NCT72 information!\n");
+ else
+ printf("NCT72(0x%x): ready\n", id2);
+
+ kval = getenv("kernelargs");
+
+ mmc = find_mmc_device(0);
+ if (mmc)
+ if (!mmc_init(mmc)) {
+ printf("MMC/SD card detected\n");
+ if (kval) {
+ int n = strlen(defkargs);
+ char *tmp = strstr(kval, defkargs);
+
+ *tmp = 0;
+ strcpy(newkernelargs, kval);
+ strcat(newkernelargs, " ");
+ strcat(newkernelargs, mmckargs);
+ strcat(newkernelargs, " ");
+ strcat(newkernelargs, &tmp[n]);
+ setenv("kernelargs", newkernelargs);
+ } else {
+ setenv("kernelargs", mmckargs);
+ }
+ }
+ get_arc_info();
+
+ if (kval) {
+ sval = getenv("SERIAL");
+ if (sval) {
+ strcpy(newkernelargs, "SN=");
+ strcat(newkernelargs, sval);
+ strcat(newkernelargs, " ");
+ strcat(newkernelargs, kval);
+ setenv("kernelargs", newkernelargs);
+ }
+ } else {
+ printf("Error reading kernelargs env variable!\n");
+ }
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[4];
+#ifdef CONFIG_TSEC2
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+#endif
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ if (is_serdes_configured(SGMII_TSEC2)) {
+ if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII2_DIS)) {
+ puts("eTSEC2 is in sgmii mode.\n");
+ tsec_info[num].flags |= TSEC_SGMII;
+ tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII;
+ }
+ }
+ num++;
+#endif
+#ifdef CONFIG_TSEC3
+ SET_STD_TSEC_INFO(tsec_info[num], 3);
+ num++;
+#endif
+
+ if (!num) {
+ printf("No TSECs initialized\n");
+ return 0;
+ }
+
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+
+ fsl_pq_mdio_init(bis, &mdio_info);
+
+ tsec_eth_init(bis, tsec_info, num);
+
+ return pci_eth_init(bis);
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+ const char *soc_usb_compat = "fsl-usb2-dr";
+ int err, usb1_off, usb2_off;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ FT_FSL_PCI_SETUP;
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
+ /* Delete eLBC node as it is muxed with USB2 controller */
+ if (hwconfig("usb2")) {
+ const char *soc_elbc_compat = "fsl,p1020-elbc";
+ int off = fdt_node_offset_by_compatible(blob, -1,
+ soc_elbc_compat);
+ if (off < 0) {
+ printf
+ ("WARNING: could not find compatible node %s: %s\n",
+ soc_elbc_compat, fdt_strerror(off));
+ return off;
+ }
+ err = fdt_del_node(blob, off);
+ if (err < 0) {
+ printf("WARNING: could not remove %s: %s\n",
+ soc_elbc_compat, fdt_strerror(err));
+ }
+ return err;
+ }
+#endif
+
+/* Delete USB2 node as it is muxed with eLBC */
+ usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat);
+ if (usb1_off < 0) {
+ printf("WARNING: could not find compatible node %s: %s.\n",
+ soc_usb_compat, fdt_strerror(usb1_off));
+ return usb1_off;
+ }
+ usb2_off =
+ fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat);
+ if (usb2_off < 0) {
+ printf("WARNING: could not find compatible node %s: %s.\n",
+ soc_usb_compat, fdt_strerror(usb2_off));
+ return usb2_off;
+ }
+ err = fdt_del_node(blob, usb2_off);
+ if (err < 0) {
+ printf("WARNING: could not remove %s: %s.\n",
+ soc_usb_compat, fdt_strerror(err));
+ }
+ return 0;
+}
+#endif
diff --git a/board/Arcturus/ucp1020/ucp1020.h b/board/Arcturus/ucp1020/ucp1020.h
new file mode 100644
index 0000000..243459c
--- /dev/null
+++ b/board/Arcturus/ucp1020/ucp1020.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * by Oleksandr G Zhadan et al.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __UCP1020_H__
+#define __UCP1020_H__
+
+#define GPIO0 31
+#define GPIO1 30
+#define GPIO2 29
+#define GPIO3 28
+#define GPIO4 27
+#define GPIO5 26
+#define GPIO6 25
+#define GPIO7 24
+#define GPIO8 23
+#define GPIO9 22
+#define GPIO10 21
+#define GPIO11 20
+#define GPIO12 19
+#define GPIO13 18
+#define GPIO14 17
+#define GPIO15 16
+#define GPIO_MAX_NUM 16
+
+#define GPIO_SDHC_CD GPIO8
+#define GPIO_SDHC_WP GPIO9
+#define GPIO_USB_PCTL0 GPIO10
+#define GPIO_PCIE1_EN GPIO11
+#define GPIO_PCIE2_EN GPIO10
+#define GPIO_USB_PCTL1 GPIO11
+
+#define GPIO_WD GPIO15
+
+static char *defkargs = "root=/dev/mtdblock1 rootfstype=cramfs ro";
+static char *mmckargs = "root=/dev/mmcblk0p1 rootwait rw";
+
+int get_arc_info(void);
+
+#endif
diff --git a/configs/UCP1020_SPIFLASH_defconfig b/configs/UCP1020_SPIFLASH_defconfig
new file mode 100644
index 0000000..2ffb8da
--- /dev/null
+++ b/configs/UCP1020_SPIFLASH_defconfig
@@ -0,0 +1,6 @@
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_UCP1020=y
+CONFIG_TARGET_UCP1020_SPIFLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_UCP1020=y
diff --git a/configs/UCP1020_defconfig b/configs/UCP1020_defconfig
new file mode 100644
index 0000000..61de360
--- /dev/null
+++ b/configs/UCP1020_defconfig
@@ -0,0 +1,5 @@
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_UCP1020=y
+CONFIG_SPI_FLASH=y
+CONFIG_UCP1020=y
diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
new file mode 100644
index 0000000..57e0c6c
--- /dev/null
+++ b/include/configs/UCP1020.h
@@ -0,0 +1,1027 @@
+/*
+ * Copyright 2013-2015 Arcturus Networks, Inc.
+ * http://www.arcturusnetworks.com/products/ucp1020/
+ * based on include/configs/p1_p2_rdb_pc.h
+ * original copyright follows:
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * QorIQ uCP1020-xx boards configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_FSL_ELBC
+#define CONFIG_PCI
+#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#if defined(CONFIG_TARTGET_UCP1020T1)
+
+#define CONFIG_UCP1020_REV_1_3
+
+#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
+#define CONFIG_P1020
+
+#define CONFIG_TSEC_ENET
+#define CONFIG_TSEC1
+#define CONFIG_TSEC3
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETHADDR 00:19:D3:FF:FF:FF
+#define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE
+#define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD
+#define CONFIG_IPADDR 10.80.41.229
+#define CONFIG_SERVERIP 10.80.41.227
+#define CONFIG_NETMASK 255.255.252.0
+#define CONFIG_ETHPRIME "eTSEC3"
+
+#ifndef CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH y
+#endif
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#define CONFIG_MMC
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+
+#define CONFIG_LAST_STAGE_INIT
+
+#if !defined(CONFIG_DONGLE)
+#define CONFIG_SILENT_CONSOLE
+#endif
+
+#endif
+
+#if defined(CONFIG_TARGET_UCP1020)
+
+#define CONFIG_UCP1020
+#define CONFIG_UCP1020_REV_1_3
+
+#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
+#define CONFIG_P1020
+
+#define CONFIG_TSEC_ENET
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+#define CONFIG_TSEC3
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETHADDR 00:06:3B:FF:FF:FF
+#define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE
+#define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD
+#define CONFIG_IPADDR 192.168.1.81
+#define CONFIG_IPADDR1 192.168.1.82
+#define CONFIG_IPADDR2 192.168.1.83
+#define CONFIG_SERVERIP 192.168.1.80
+#define CONFIG_GATEWAYIP 102.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#ifndef CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH y
+#endif
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#define CONFIG_MMC
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+
+#define CONFIG_LAST_STAGE_INIT
+
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+#define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500
+/* #define CONFIG_MPC85xx */
+
+#define CONFIG_MP
+
+#define CONFIG_FSL_LAW
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_CMD_SATA
+#define CONFIG_SATA_SIL
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
+#define CONFIG_SYS_CLK_FREQ 66666666
+#define CONFIG_DDR_CLK_FREQ 66666666
+
+#define CONFIG_HWCONFIG
+
+#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
+#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
+#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
+/*
+ * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
+ * there will be one entry in this array for each two (dummy) sensors in
+ * CONFIG_DTT_SENSORS.
+ *
+ * For uCP1020 module:
+ * - only one ADM1021/NCT72
+ * - i2c addr 0x41
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT output disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
+ */
+#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
+ 0x02, 0, 1, 0, 85, 1, 0, 85} }
+
+#define CONFIG_CMD_DTT
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE
+#define CONFIG_BTB
+
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x1fffffff
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+
+/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
+ SPL code*/
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#endif
+
+/* DDR Setup */
+#define CONFIG_DDR_ECC_ENABLE
+#define CONFIG_SYS_FSL_DDR3
+#ifndef CONFIG_DDR_ECC_ENABLE
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_DDR_SPD
+#endif
+#define CONFIG_SYS_SPD_BUS_NUM 1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+
+/* Default settings for DDR3 */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
+#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
+#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
+#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
+#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
+
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
+#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
+#define CONFIG_SYS_DDR_RCW_1 0x00000000
+#define CONFIG_SYS_DDR_RCW_2 0x00000000
+#ifdef CONFIG_DDR_ECC_ENABLE
+#define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */
+#else
+#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
+#endif
+#define CONFIG_SYS_DDR_CONTROL_2 0x04401050
+#define CONFIG_SYS_DDR_TIMING_4 0x00220001
+#define CONFIG_SYS_DDR_TIMING_5 0x03402400
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00020000
+#define CONFIG_SYS_DDR_TIMING_0 0x00330004
+#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
+#define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
+#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
+#define CONFIG_SYS_DDR_MODE_1 0x40461520
+#define CONFIG_SYS_DDR_MODE_2 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL 0x0C300000
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
+ * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2)
+ * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
+ * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable
+ * (early boot only)
+ * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
+ * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
+ * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
+#define CONFIG_SYS_FLASH_BASE 0xec000000
+
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+ | BR_PS_16 | BR_V)
+
+#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
+
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
+/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+/* Size of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
+
+#define CONFIG_SYS_PMC_BASE 0xff980000
+#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
+#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
+ BR_PS_8 | BR_V)
+#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
+ OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
+ OR_GPCM_EAD)
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
+#ifdef CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#endif
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
+#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
+
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
+#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
+#define CONFIG_SYS_I2C_IDT6V49205B 0x69
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_SPI_FLASH_SST 1
+#define CONFIG_SPI_FLASH_STMICRO 1
+#define CONFIG_SPI_FLASH_WINBOND 1
+#define CONFIG_CMD_SF 1
+#define CONFIG_CMD_SPI 1
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9"
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 1, Slot 2, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10"
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/*
+ * Environment
+ */
+#ifdef CONFIG_ENV_FIT_UCBOOT
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
+#define CONFIG_ENV_SIZE 0x20000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+
+#else
+
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+
+#ifdef CONFIG_RAMBOOT_SPIFLASH
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x3000 /* 12KB */
+#define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
+#define CONFIG_ENV_SECT_SIZE 0x1000
+
+#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#endif
+
+#elif defined(CONFIG_RAMBOOT_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#elif defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x2000
+
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000)
+#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#endif
+
+#endif
+
+#endif /* CONFIG_ENV_FIT_UCBOOT */
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_CRAMFS
+#define CONFIG_CRAMFS_CMDLINE
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+#define CONFIG_USB_EHCI
+
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_MMC_SPI
+#define CONFIG_CMD_MMC_SPI
+#define CONFIG_GENERIC_MMC
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Misc Extra Settings */
+#define CONFIG_CMD_GPIO 1
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "B$ " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#if defined(CONFIG_UCP1020_REV_1_2)
+#define CONFIG_PHY_MICREL_KSZ9021
+#elif defined(CONFIG_UCP1020_REV_1_3)
+#define CONFIG_PHY_MICREL_KSZ9031
+#else
+#error "UCP1020 module revision is not defined !!!"
+#endif
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_SERVERIP
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3_NAME "eTSEC3"
+
+#define TSEC1_PHY_ADDR 4
+#define TSEC2_PHY_ADDR 0
+#define TSEC2_PHY_ADDR_SGMII 0x00
+#define TSEC3_PHY_ADDR 6
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+
+#endif
+
+#define CONFIG_HOSTNAME UCP1020
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+/*
+ * Autobooting
+ */
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_STOP_STR "\x1b"
+#define DEBUG_BOOTKEYS 0
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#undef CONFIG_BOOTARGS
+#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \
+ "press \"<Esc>\" to stop\n", bootdelay
+
+#define CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#if defined(CONFIG_DONGLE)
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"bootcmd=run prog_spi_mbrbootcramfs\0" \
+"bootfile=uImage\0" \
+"consoledev=ttyS0\0" \
+"cramfsfile=image.cramfs\0" \
+"dtbaddr=0x00c00000\0" \
+"dtbfile=image.dtb\0" \
+"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
+"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
+"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
+"fileaddr=0x01000000\0" \
+"filesize=0x00080000\0" \
+"flashmbr=sf probe 0; " \
+ "tftp $loadaddr $mbr; " \
+ "sf erase $mbr_offset +$filesize; " \
+ "sf write $loadaddr $mbr_offset $filesize\0" \
+"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
+ "protect off $nor_recoveryaddr +$filesize; " \
+ "erase $nor_recoveryaddr +$filesize; " \
+ "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
+ "protect on $nor_recoveryaddr +$filesize\0 " \
+"flashuboot=tftp $ubootaddr $ubootfile; " \
+ "protect off $nor_ubootaddr +$filesize; " \
+ "erase $nor_ubootaddr +$filesize; " \
+ "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
+ "protect on $nor_ubootaddr +$filesize\0 " \
+"flashworking=tftp $workingaddr $cramfsfile; " \
+ "protect off $nor_workingaddr +$filesize; " \
+ "erase $nor_workingaddr +$filesize; " \
+ "cp.b $workingaddr $nor_workingaddr $filesize; " \
+ "protect on $nor_workingaddr +$filesize\0 " \
+"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
+"kerneladdr=0x01100000\0" \
+"kernelfile=uImage\0" \
+"loadaddr=0x01000000\0" \
+"mbr=uCP1020d.mbr\0" \
+"mbr_offset=0x00000000\0" \
+"mmbr=uCP1020Quiet.mbr\0" \
+"mmcpart=0:2\0" \
+"mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
+ "mmc erase 1 1; " \
+ "mmc write $loadaddr 1 1\0" \
+"mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \
+ "mmc erase 0x40 0x400; " \
+ "mmc write $loadaddr 0x40 0x400\0" \
+"netdev=eth0\0" \
+"nor_recoveryaddr=0xEC0A0000\0" \
+"nor_ubootaddr=0xEFF80000\0" \
+"nor_workingaddr=0xECFA0000\0" \
+"norbootrecovery=setenv bootargs $recoverybootargs" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "run norloadrecovery; " \
+ "bootm $kerneladdr - $dtbaddr\0" \
+"norbootworking=setenv bootargs $workingbootargs" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "run norloadworking; " \
+ "bootm $kerneladdr - $dtbaddr\0" \
+"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
+ "setenv cramfsaddr $nor_recoveryaddr; " \
+ "cramfsload $dtbaddr $dtbfile; " \
+ "cramfsload $kerneladdr $kernelfile\0" \
+"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
+ "setenv cramfsaddr $nor_workingaddr; " \
+ "cramfsload $dtbaddr $dtbfile; " \
+ "cramfsload $kerneladdr $kernelfile\0" \
+"prog_spi_mbr=run spi__mbr\0" \
+"prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \
+"prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
+ "run spi__cramfs\0" \
+"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $rootfsaddr $rootfsfile; " \
+ "tftp $loadaddr $kernelfile; " \
+ "tftp $dtbaddr $dtbfile; " \
+ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
+"ramdisk_size=120000\0" \
+"ramdiskfile=rootfs.ext2.gz.uboot\0" \
+"recoveryaddr=0x02F00000\0" \
+"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
+"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
+ "mw.l 0xffe0f008 0x00400000\0" \
+"rootfsaddr=0x02F00000\0" \
+"rootfsfile=rootfs.ext2.gz.uboot\0" \
+"rootpath=/opt/nfsroot\0" \
+"spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
+ "protect off 0xeC000000 +$filesize; " \
+ "erase 0xEC000000 +$filesize; " \
+ "cp.b $loadaddr 0xEC000000 $filesize; " \
+ "cmp.b $loadaddr 0xEC000000 $filesize; " \
+ "protect on 0xeC000000 +$filesize\0" \
+"spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
+ "protect off 0xeFF80000 +$filesize; " \
+ "erase 0xEFF80000 +$filesize; " \
+ "cp.b $loadaddr 0xEFF80000 $filesize; " \
+ "cmp.b $loadaddr 0xEFF80000 $filesize; " \
+ "protect on 0xeFF80000 +$filesize\0" \
+"spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \
+ "sf probe 0; sf erase 0x8000 +$filesize; " \
+ "sf write $loadaddr 0x8000 $filesize\0" \
+"spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \
+ "protect off 0xec0a0000 +$filesize; " \
+ "erase 0xeC0A0000 +$filesize; " \
+ "cp.b $loadaddr 0xeC0A0000 $filesize; " \
+ "protect on 0xec0a0000 +$filesize\0" \
+"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
+ "sf probe 1; sf erase 0 +$filesize; " \
+ "sf write $loadaddr 0 $filesize\0" \
+"spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
+ "sf probe 0; sf erase 0 +$filesize; " \
+ "sf write $loadaddr 0 $filesize\0" \
+"tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
+"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
+"ubootaddr=0x01000000\0" \
+"ubootfile=u-boot.bin\0" \
+"ubootd=u-boot4dongle.bin\0" \
+"upgrade=run flashworking\0" \
+"usb_phy_type=ulpi\0 " \
+"workingaddr=0x02F00000\0" \
+"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
+
+#else
+
+#if defined(CONFIG_UCP1020T1)
+
+#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
+"bootfile=uImage\0" \
+"consoledev=ttyS0\0" \
+"cramfsfile=image.cramfs\0" \
+"dtbaddr=0x00c00000\0" \
+"dtbfile=image.dtb\0" \
+"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
+"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
+"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
+"fileaddr=0x01000000\0" \
+"filesize=0x00080000\0" \
+"flashmbr=sf probe 0; " \
+ "tftp $loadaddr $mbr; " \
+ "sf erase $mbr_offset +$filesize; " \
+ "sf write $loadaddr $mbr_offset $filesize\0" \
+"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
+ "protect off $nor_recoveryaddr +$filesize; " \
+ "erase $nor_recoveryaddr +$filesize; " \
+ "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
+ "protect on $nor_recoveryaddr +$filesize\0 " \
+"flashuboot=tftp $ubootaddr $ubootfile; " \
+ "protect off $nor_ubootaddr +$filesize; " \
+ "erase $nor_ubootaddr +$filesize; " \
+ "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
+ "protect on $nor_ubootaddr +$filesize\0 " \
+"flashworking=tftp $workingaddr $cramfsfile; " \
+ "protect off $nor_workingaddr +$filesize; " \
+ "erase $nor_workingaddr +$filesize; " \
+ "cp.b $workingaddr $nor_workingaddr $filesize; " \
+ "protect on $nor_workingaddr +$filesize\0 " \
+"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
+"kerneladdr=0x01100000\0" \
+"kernelfile=uImage\0" \
+"loadaddr=0x01000000\0" \
+"mbr=uCP1020.mbr\0" \
+"mbr_offset=0x00000000\0" \
+"netdev=eth0\0" \
+"nor_recoveryaddr=0xEC0A0000\0" \
+"nor_ubootaddr=0xEFF80000\0" \
+"nor_workingaddr=0xECFA0000\0" \
+"norbootrecovery=setenv bootargs $recoverybootargs" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "run norloadrecovery; " \
+ "bootm $kerneladdr - $dtbaddr\0" \
+"norbootworking=setenv bootargs $workingbootargs" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "run norloadworking; " \
+ "bootm $kerneladdr - $dtbaddr\0" \
+"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
+ "setenv cramfsaddr $nor_recoveryaddr; " \
+ "cramfsload $dtbaddr $dtbfile; " \
+ "cramfsload $kerneladdr $kernelfile\0" \
+"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
+ "setenv cramfsaddr $nor_workingaddr; " \
+ "cramfsload $dtbaddr $dtbfile; " \
+ "cramfsload $kerneladdr $kernelfile\0" \
+"othbootargs=quiet\0" \
+"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $rootfsaddr $rootfsfile; " \
+ "tftp $loadaddr $kernelfile; " \
+ "tftp $dtbaddr $dtbfile; " \
+ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
+"ramdisk_size=120000\0" \
+"ramdiskfile=rootfs.ext2.gz.uboot\0" \
+"recoveryaddr=0x02F00000\0" \
+"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
+"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
+ "mw.l 0xffe0f008 0x00400000\0" \
+"rootfsaddr=0x02F00000\0" \
+"rootfsfile=rootfs.ext2.gz.uboot\0" \
+"rootpath=/opt/nfsroot\0" \
+"silent=1\0" \
+"tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
+"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
+"ubootaddr=0x01000000\0" \
+"ubootfile=u-boot.bin\0" \
+"upgrade=run flashworking\0" \
+"workingaddr=0x02F00000\0" \
+"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
+
+#else /* For Arcturus Modules */
+
+#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"bootcmd=run norkernel\0" \
+"bootfile=uImage\0" \
+"consoledev=ttyS0\0" \
+"dtbaddr=0x00c00000\0" \
+"dtbfile=image.dtb\0" \
+"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
+"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
+"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
+"fileaddr=0x01000000\0" \
+"filesize=0x00080000\0" \
+"flashmbr=sf probe 0; " \
+ "tftp $loadaddr $mbr; " \
+ "sf erase $mbr_offset +$filesize; " \
+ "sf write $loadaddr $mbr_offset $filesize\0" \
+"flashuboot=tftp $loadaddr $ubootfile; " \
+ "protect off $nor_ubootaddr0 +$filesize; " \
+ "erase $nor_ubootaddr0 +$filesize; " \
+ "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \
+ "protect on $nor_ubootaddr0 +$filesize; " \
+ "protect off $nor_ubootaddr1 +$filesize; " \
+ "erase $nor_ubootaddr1 +$filesize; " \
+ "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \
+ "protect on $nor_ubootaddr1 +$filesize\0 " \
+"format0=protect off $part0base +$part0size; " \
+ "erase $part0base +$part0size\0" \
+"format1=protect off $part1base +$part1size; " \
+ "erase $part1base +$part1size\0" \
+"format2=protect off $part2base +$part2size; " \
+ "erase $part2base +$part2size\0" \
+"format3=protect off $part3base +$part3size; " \
+ "erase $part3base +$part3size\0" \
+"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
+"kerneladdr=0x01100000\0" \
+"kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \
+"kernelfile=uImage\0" \
+"loadaddr=0x01000000\0" \
+"mbr=uCP1020.mbr\0" \
+"mbr_offset=0x00000000\0" \
+"netdev=eth0\0" \
+"nor_ubootaddr0=0xEC000000\0" \
+"nor_ubootaddr1=0xEFF80000\0" \
+"norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
+ "run norkernelload; " \
+ "bootm $kerneladdr - $dtbaddr\0" \
+"norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \
+ "setenv cramfsaddr $part0base; " \
+ "cramfsload $dtbaddr $dtbfile; " \
+ "cramfsload $kerneladdr $kernelfile\0" \
+"part0base=0xEC100000\0" \
+"part0size=0x00700000\0" \
+"part1base=0xEC800000\0" \
+"part1size=0x02000000\0" \
+"part2base=0xEE800000\0" \
+"part2size=0x00800000\0" \
+"part3base=0xEF000000\0" \
+"part3size=0x00F80000\0" \
+"partENVbase=0xEC080000\0" \
+"partENVsize=0x00080000\0" \
+"program0=tftp part0-000000.bin; " \
+ "protect off $part0base +$filesize; " \
+ "erase $part0base +$filesize; " \
+ "cp.b $loadaddr $part0base $filesize; " \
+ "echo Verifying...; " \
+ "cmp.b $loadaddr $part0base $filesize\0" \
+"program1=tftp part1-000000.bin; " \
+ "protect off $part1base +$filesize; " \
+ "erase $part1base +$filesize; " \
+ "cp.b $loadaddr $part1base $filesize; " \
+ "echo Verifying...; " \
+ "cmp.b $loadaddr $part1base $filesize\0" \
+"program2=tftp part2-000000.bin; " \
+ "protect off $part2base +$filesize; " \
+ "erase $part2base +$filesize; " \
+ "cp.b $loadaddr $part2base $filesize; " \
+ "echo Verifying...; " \
+ "cmp.b $loadaddr $part2base $filesize\0" \
+"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
+ " console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $rootfsaddr $rootfsfile; " \
+ "tftp $loadaddr $kernelfile; " \
+ "tftp $dtbaddr $dtbfile; " \
+ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
+"ramdisk_size=120000\0" \
+"ramdiskfile=rootfs.ext2.gz.uboot\0" \
+"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
+ "mw.l 0xffe0f008 0x00400000\0" \
+"rootfsaddr=0x02F00000\0" \
+"rootfsfile=rootfs.ext2.gz.uboot\0" \
+"rootpath=/opt/nfsroot\0" \
+"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
+ "sf probe 0; sf erase 0 +$filesize; " \
+ "sf write $loadaddr 0 $filesize\0" \
+"spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
+ "protect off 0xeC000000 +$filesize; " \
+ "erase 0xEC000000 +$filesize; " \
+ "cp.b $loadaddr 0xEC000000 $filesize; " \
+ "cmp.b $loadaddr 0xEC000000 $filesize; " \
+ "protect on 0xeC000000 +$filesize\0" \
+"tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
+"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
+"ubootfile=u-boot.bin\0" \
+"upgrade=run flashuboot\0" \
+"usb_phy_type=ulpi\0 " \
+"boot_nfs= " \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr\0" \
+"boot_hd = " \
+ "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "usb start;" \
+ "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
+ "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
+ "bootm $loadaddr - $fdtaddr\0" \
+"boot_usb_fat = " \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs " \
+ "ramdisk_size=$ramdisk_size;" \
+ "usb start;" \
+ "fatload usb 0:2 $loadaddr $bootfile;" \
+ "fatload usb 0:2 $fdtaddr $fdtfile;" \
+ "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
+"boot_usb_ext2 = " \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs " \
+ "ramdisk_size=$ramdisk_size;" \
+ "usb start;" \
+ "ext2load usb 0:4 $loadaddr $bootfile;" \
+ "ext2load usb 0:4 $fdtaddr $fdtfile;" \
+ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
+"boot_nor = " \
+ "setenv bootargs root=/dev/$jffs2nor rw " \
+ "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
+ "bootm $norbootaddr - $norfdtaddr\0 " \
+"boot_ram = " \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs " \
+ "ramdisk_size=$ramdisk_size;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
+
+#endif
+#endif
+
+#endif /* __CONFIG_H */
--
2.1.4
More information about the U-Boot
mailing list