[U-Boot] [PATCH 1/1] fsl_qspi: Pet the watchdog while reading/writing

[Huan Wang]

Hi, York,

> On Wednesday 25 November 2015 02:20:53, Huan Wang wrote:
> > [Alison Wang] I didn't meet any issue when using sf commands to write
> > and read the serial flash.
> >
> > Hi, Alexander,
> >
> > 	Could you show me the detail commands and process when you meet
> such
> > issue? Then I can try to reproduce on my board.
> 
> Yep, here is the output:
> > U-Boot 2015.01-00671-g78773b9 (Nov 25 2015 - 10:28:50)
> >
> > CPU:   Freescale LayerScape LS1021E, Version: 2.0, (0x87081120)
> >
> > Clock Configuration:
> >        CPU0(ARMV7):960  MHz,
> >        Bus:288  MHz, DDR:800  MHz (1600 MT/s data rate), Reset
> > Configuration Word (RCW):
> >        00000000: 0608000a 00000000 00000000 00000000
> >        00000010: 70000000 08407922 40000a00 21046000
> >        00000020: 00000000 00000000 00000000 0021ef00
> >        00000030: 20024800 0888f340 00000000 00000000 QSPI
> >        Watchdog enabled
> > I2C:   ready
> > DRAM:  Initializing DDR....
> > Detected UDIMM Fixed DDR on board
> > 512 MiB (DDR3, 16-bit, CL=11, ECC off) Using SERDES1 Protocol: 112
> > (0x70)
> > MMC:   FSL_SDHC: 0
> > SF: Detected S25FL512S_256K with page size 512 Bytes, erase size 256
> KiB,
> > In:    serial
> > Out:   serial
> > Err:   serial
> > SF: Detected S25FL512S_256K with page size 512 Bytes, erase size 256
> > KiB, total 64 MiB SF: 262144 bytes @ 0x180000 Read: OK Firmware
> > 'Microcode version 0.0.1 for LS1021a r1.0' for 1021 V1.0
> > QE: uploading microcode 'Microcode for LS1021a r1.0' version 0.0.1
> > SCSI:  Net:   eTSEC2 is in sgmii mode.
> > eTSEC1 [PRIME], eTSEC2
> > Hit any key to stop autoboot:  0
> > => sf read 0x81040000 0x200000 0x400000
> >
> >
> > U-Boot 2015.01-00671-g78773b9 (Nov 25 2015 - 10:28:50)
> >
> > CPU:   Freescale LayerScape LS1021E, Version: 2.0, (0x87081120)
> >
> > Clock Configuration:
> >        CPU0(ARMV7):960  MHz,
> >        Bus:288  MHz, DDR:800  MHz (1600 MT/s data rate), Reset
> > Configuration Word (RCW):
> >        00000000: 0608000a 00000000 00000000 00000000
> >        00000010: 70000000 08407922 40000a00 21046000
> >        00000020: 00000000 00000000 00000000 0021ef00
> >        00000030: 20024800 0888f340 00000000 00000000 QSPI
> >        Watchdog enabled
> > I2C:   ready
> > DRAM:  Initializing DDR....
> > Detected UDIMM Fixed DDR on board
> > [...]
> and so on...
> 
> The actual command which results in a watchdog reset is 'sf read
> 0x81040000 0x200000 0x400000'. Please note that this uses an external
> watchdog which is enabled by default and resets after ~1.5s. The command
> itself takes about 2s (taken from my watch).
> 
[Alison Wang] I could not reproduce the issue. Maybe I don't have the
external watchdog which will reset after ~1.5s as Alexander mentioned.

U-Boot 2015.10-00273-g7ee52af (Dec 03 2015 - 17:32:24 +0800)

CPU:   Freescale LayerScape LS1021E, Version: 2.0, (0x87081120)
Clock Configuration:
       CPU0(ARMV7):1000 MHz,
       Bus:300  MHz, DDR:800  MHz (1600 MT/s data rate),
Reset Configuration Word (RCW):
       00000000: 0608000a 00000000 00000000 00000000
       00000010: 30000000 00007900 40025a00 21046000
       00000020: 00000000 00000000 00000000 20000000
       00000030: 20024800 881b7540 00000000 00000000
Model: LS1021A TWR Board
Board: LS1021ATWR
I2C:   ready
DRAM:  1 GiB
Using SERDES1 Protocol: 48 (0x30)
MMC:   FSL_SDHC: 0
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
EEPROM: NXID v1
PCIe1: Root Complex no link, regs @ 0x3400000
PCIe2: disabled
In:    serial
Out:   serial
Err:   serial
SEC: RNG instantiated
SATA link 0 timeout.
AHCI 0001.0300 1 slots 1 ports ? Gbps 0x1 impl SATA mode
flags: 64bit ncq pm clo only pmp fbss pio slum part ccc
Found 0 device(s).
SCSI:  Net:   eTSEC1 is in sgmii mode.
eTSEC2 is in sgmii mode.
eTSEC1, eTSEC2, eTSEC3 [PRIME]
=> => sf probe
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
=> sf read 0x81040000 0x200000 0x400000
device 0 offset 0x200000, size 0x400000
SF: 4194304 bytes @ 0x200000 Read: OK
=>


Best Regards,
Alison Wang