[U-Boot] [PATCH 07/10] net: axi_emac: Move driver to DM
Joe Hershberger
joe.hershberger at gmail.com
Tue Dec 15 20:52:33 CET 2015
Hi Michal,
On Tue, Dec 15, 2015 at 1:40 PM, Michal Simek <michal.simek at xilinx.com> wrote:
> On 15.12.2015 19:57, Simon Glass wrote:
>> Hi Michal,
>>
>> On 11 December 2015 at 04:59, Michal Simek <michal.simek at xilinx.com> wrote:
>>> Move driver to DM.
>>>
>>> Signed-off-by: Michal Simek <michal.simek at xilinx.com>
>>> ---
>>>
>>> .../xilinx/microblaze-generic/microblaze-generic.c | 5 -
>>> board/xilinx/zynq/board.c | 4 -
>>> drivers/net/xilinx_axi_emac.c | 190 +++++++++++++--------
>>> include/netdev.h | 2 -
>>> 4 files changed, 122 insertions(+), 79 deletions(-)
>>
>> Reviewed-by: Simon Glass <sjg at chromium.org>
>>
>> See a few things below.
>>
>>>
>>> diff --git a/board/xilinx/microblaze-generic/microblaze-generic.c b/board/xilinx/microblaze-generic/microblaze-generic.c
>>> index dfa629322223..a3122da9acaa 100644
>>> --- a/board/xilinx/microblaze-generic/microblaze-generic.c
>>> +++ b/board/xilinx/microblaze-generic/microblaze-generic.c
>>> @@ -105,11 +105,6 @@ int board_eth_init(bd_t *bis)
>>> {
>>> int ret = 0;
>>>
>>> -#ifdef CONFIG_XILINX_AXIEMAC
>>> - ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR,
>>> - XILINX_AXIDMA_BASEADDR);
>>> -#endif
>>> -
>>> #if defined(CONFIG_XILINX_EMACLITE) && defined(XILINX_EMACLITE_BASEADDR)
>>> u32 txpp = 0;
>>> u32 rxpp = 0;
>>> diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
>>> index 414f5302a066..427e75485deb 100644
>>> --- a/board/xilinx/zynq/board.c
>>> +++ b/board/xilinx/zynq/board.c
>>> @@ -103,10 +103,6 @@ int board_eth_init(bd_t *bis)
>>> {
>>> u32 ret = 0;
>>>
>>> -#ifdef CONFIG_XILINX_AXIEMAC
>>> - ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR,
>>> - XILINX_AXIDMA_BASEADDR);
>>> -#endif
>>> #ifdef CONFIG_XILINX_EMACLITE
>>> u32 txpp = 0;
>>> u32 rxpp = 0;
>>> diff --git a/drivers/net/xilinx_axi_emac.c b/drivers/net/xilinx_axi_emac.c
>>> index 77b1869dc9dc..c03f8f730d3a 100644
>>> --- a/drivers/net/xilinx_axi_emac.c
>>> +++ b/drivers/net/xilinx_axi_emac.c
>>> @@ -8,12 +8,15 @@
>>>
>>> #include <config.h>
>>> #include <common.h>
>>> +#include <dm.h>
>>> #include <net.h>
>>> #include <malloc.h>
>>> #include <asm/io.h>
>>> #include <phy.h>
>>> #include <miiphy.h>
>>>
>>> +DECLARE_GLOBAL_DATA_PTR;
>>> +
>>> #if !defined(CONFIG_PHYLIB)
>>> # error AXI_ETHERNET requires PHYLIB
>>> #endif
>>> @@ -87,6 +90,7 @@ struct axidma_priv {
>>> struct axidma_reg *dmarx;
>>> int phyaddr;
>>> struct axi_regs *iobase;
>>> + phy_interface_t interface;
>>> struct phy_device *phydev;
>>> struct mii_dev *bus;
>>> };
>>> @@ -218,11 +222,11 @@ static u32 phywrite(struct axidma_priv *priv, u32 phyaddress, u32 registernum,
>>> }
>>>
>>> /* Setting axi emac and phy to proper setting */
>>> -static int setup_phy(struct eth_device *dev)
>>> +static int setup_phy(struct udevice *dev)
>>> {
>>> u16 phyreg;
>>> u32 i, speed, emmc_reg, ret;
>>> - struct axidma_priv *priv = dev->priv;
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> struct axi_regs *regs = priv->iobase;
>>> struct phy_device *phydev;
>>>
>>> @@ -298,9 +302,9 @@ static int setup_phy(struct eth_device *dev)
>>> }
>>>
>>> /* STOP DMA transfers */
>>> -static void axiemac_halt(struct eth_device *dev)
>>> +static void axiemac_halt(struct udevice *dev)
>>> {
>>> - struct axidma_priv *priv = dev->priv;
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> u32 temp;
>>>
>>> /* Stop the hardware */
>>> @@ -358,16 +362,18 @@ static int axi_ethernet_init(struct axidma_priv *priv)
>>> return 0;
>>> }
>>>
>>> -static int axiemac_setup_mac(struct eth_device *dev)
>>> +static int axiemac_setup_mac(struct udevice *dev)
>>> {
>>> - struct axi_regs *regs = (struct axi_regs *)dev->iobase;
>>> + struct eth_pdata *pdata = dev_get_platdata(dev);
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> + struct axi_regs *regs = priv->iobase;
>>>
>>> /* Set the MAC address */
>>> - int val = ((dev->enetaddr[3] << 24) | (dev->enetaddr[2] << 16) |
>>> - (dev->enetaddr[1] << 8) | (dev->enetaddr[0]));
>>> + int val = ((pdata->enetaddr[3] << 24) | (pdata->enetaddr[2] << 16) |
>>> + (pdata->enetaddr[1] << 8) | (pdata->enetaddr[0]));
>>> out_be32(®s->uaw0, val);
>>>
>>> - val = (dev->enetaddr[5] << 8) | dev->enetaddr[4] ;
>>> + val = (pdata->enetaddr[5] << 8) | pdata->enetaddr[4];
>>> val |= in_be32(®s->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
>>> out_be32(®s->uaw1, val);
>>> return 0;
>>> @@ -396,10 +402,10 @@ static void axi_dma_init(struct axidma_priv *priv)
>>> printf("%s: Timeout\n", __func__);
>>> }
>>>
>>> -static int axiemac_init(struct eth_device *dev, bd_t * bis)
>>> +static int axiemac_init(struct udevice *dev)
>>> {
>>> - struct axidma_priv *priv = dev->priv;
>>> - struct axi_regs *regs = (struct axi_regs *)dev->iobase;
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> + struct axi_regs *regs = priv->iobase;
>>> u32 temp;
>>>
>>> debug("axiemac: Init started\n");
>>> @@ -458,9 +464,9 @@ static int axiemac_init(struct eth_device *dev, bd_t * bis)
>>> return 0;
>>> }
>>>
>>> -static int axiemac_send(struct eth_device *dev, void *ptr, int len)
>>> +static int axiemac_send(struct udevice *dev, void *ptr, int len)
>>> {
>>> - struct axidma_priv *priv = dev->priv;
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> u32 timeout;
>>>
>>> if (len > PKTSIZE_ALIGN)
>>> @@ -530,15 +536,15 @@ static int isrxready(struct axidma_priv *priv)
>>> return 0;
>>> }
>>>
>>> -static int axiemac_recv(struct eth_device *dev)
>>> +static int axiemac_recv(struct udevice *dev, int flags, uchar **packetp)
>>> {
>>> u32 length;
>>> - struct axidma_priv *priv = dev->priv;
>>> + struct axidma_priv *priv = dev_get_priv(dev);
>>> u32 temp;
>>>
>>> /* Wait for an incoming packet */
>>> if (!isrxready(priv))
>>> - return 0;
>>> + return -1;
>>
>> I suggest -EAGAIN
>>
>>>
>>> debug("axiemac: RX data ready\n");
>>>
>>> @@ -578,77 +584,125 @@ static int axiemac_recv(struct eth_device *dev)
>>>
>>> debug("axiemac: RX completed, framelength = %d\n", length);
>>>
>>> - return length;
>>> + return 0;
>>
>> You do need to return the length here. You could update net.h to make
>> this clearer.
>
> Are you sure?
>
> recv part is calling net_process_received_packet(rxframe, length);
> already and then the core is checking for returning value. which should
> be 0 or less to quit this loop.
>
> 447 for (i = 0; i < 32; i++) {
> 448 ret = eth_get_ops(current)->recv(current, flags,
> &packet);
> 449 flags = 0;
> 450 if (ret > 0)
If you return 0, your packet is not processed. 0 means you got nothing.
> 451 net_process_received_packet(packet, ret);
> 452 if (ret >= 0 && eth_get_ops(current)->free_pkt)
> 453 eth_get_ops(current)->free_pkt(current,
> packet, ret );
> 454 if (ret <= 0)
> 455 break;
> 456 }
>
> Thanks,
> Michal
>
>
>
>
>
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
More information about the U-Boot
mailing list