[U-Boot] [PATCH 07/10] net: axi_emac: Move driver to DM

Michal Simek michal.simek at xilinx.com
Wed Dec 16 09:20:05 CET 2015


On 15.12.2015 21:31, Joe Hershberger wrote:
> On Fri, Dec 11, 2015 at 5:59 AM, Michal Simek <michal.simek at xilinx.com> wrote:
>> Move driver to DM.
>>
>> Signed-off-by: Michal Simek <michal.simek at xilinx.com>
> 
> Other than a few nits below and the issue with recv return value,
> 
> Acked-by: Joe Hershberger <joe.hershberger>
> 
>>  .../xilinx/microblaze-generic/microblaze-generic.c |   5 -
>>  board/xilinx/zynq/board.c                          |   4 -
>>  drivers/net/xilinx_axi_emac.c                      | 190 +++++++++++++--------
>>  include/netdev.h                                   |   2 -
>>  4 files changed, 122 insertions(+), 79 deletions(-)
>>
>> diff --git a/board/xilinx/microblaze-generic/microblaze-generic.c b/board/xilinx/microblaze-generic/microblaze-generic.c
>> index dfa629322223..a3122da9acaa 100644
>> --- a/board/xilinx/microblaze-generic/microblaze-generic.c
>> +++ b/board/xilinx/microblaze-generic/microblaze-generic.c
>> @@ -105,11 +105,6 @@ int board_eth_init(bd_t *bis)
>>  {
>>         int ret = 0;
>>
>> -#ifdef CONFIG_XILINX_AXIEMAC
>> -       ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR,
>> -                                               XILINX_AXIDMA_BASEADDR);
>> -#endif
>> -
>>  #if defined(CONFIG_XILINX_EMACLITE) && defined(XILINX_EMACLITE_BASEADDR)
>>         u32 txpp = 0;
>>         u32 rxpp = 0;
>> diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
>> index 414f5302a066..427e75485deb 100644
>> --- a/board/xilinx/zynq/board.c
>> +++ b/board/xilinx/zynq/board.c
>> @@ -103,10 +103,6 @@ int board_eth_init(bd_t *bis)
>>  {
>>         u32 ret = 0;
>>
>> -#ifdef CONFIG_XILINX_AXIEMAC
>> -       ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR,
>> -                                               XILINX_AXIDMA_BASEADDR);
>> -#endif
>>  #ifdef CONFIG_XILINX_EMACLITE
>>         u32 txpp = 0;
>>         u32 rxpp = 0;
>> diff --git a/drivers/net/xilinx_axi_emac.c b/drivers/net/xilinx_axi_emac.c
>> index 77b1869dc9dc..c03f8f730d3a 100644
>> --- a/drivers/net/xilinx_axi_emac.c
>> +++ b/drivers/net/xilinx_axi_emac.c
>> @@ -8,12 +8,15 @@
>>
>>  #include <config.h>
>>  #include <common.h>
>> +#include <dm.h>
>>  #include <net.h>
>>  #include <malloc.h>
>>  #include <asm/io.h>
>>  #include <phy.h>
>>  #include <miiphy.h>
>>
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>>  #if !defined(CONFIG_PHYLIB)
>>  # error AXI_ETHERNET requires PHYLIB
>>  #endif
>> @@ -87,6 +90,7 @@ struct axidma_priv {
>>         struct axidma_reg *dmarx;
>>         int phyaddr;
>>         struct axi_regs *iobase;
>> +       phy_interface_t interface;
>>         struct phy_device *phydev;
>>         struct mii_dev *bus;
>>  };
>> @@ -218,11 +222,11 @@ static u32 phywrite(struct axidma_priv *priv, u32 phyaddress, u32 registernum,
>>  }
>>
>>  /* Setting axi emac and phy to proper setting */
>> -static int setup_phy(struct eth_device *dev)
>> +static int setup_phy(struct udevice *dev)
>>  {
>>         u16 phyreg;
>>         u32 i, speed, emmc_reg, ret;
>> -       struct axidma_priv *priv = dev->priv;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>>         struct axi_regs *regs = priv->iobase;
>>         struct phy_device *phydev;
>>
>> @@ -298,9 +302,9 @@ static int setup_phy(struct eth_device *dev)
>>  }
>>
>>  /* STOP DMA transfers */
>> -static void axiemac_halt(struct eth_device *dev)
>> +static void axiemac_halt(struct udevice *dev)
>>  {
>> -       struct axidma_priv *priv = dev->priv;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>>         u32 temp;
>>
>>         /* Stop the hardware */
>> @@ -358,16 +362,18 @@ static int axi_ethernet_init(struct axidma_priv *priv)
>>         return 0;
>>  }
>>
>> -static int axiemac_setup_mac(struct eth_device *dev)
>> +static int axiemac_setup_mac(struct udevice *dev)
>>  {
>> -       struct axi_regs *regs = (struct axi_regs *)dev->iobase;
>> +       struct eth_pdata *pdata = dev_get_platdata(dev);
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>> +       struct axi_regs *regs = priv->iobase;
>>
>>         /* Set the MAC address */
>> -       int val = ((dev->enetaddr[3] << 24) | (dev->enetaddr[2] << 16) |
>> -               (dev->enetaddr[1] << 8) | (dev->enetaddr[0]));
>> +       int val = ((pdata->enetaddr[3] << 24) | (pdata->enetaddr[2] << 16) |
>> +               (pdata->enetaddr[1] << 8) | (pdata->enetaddr[0]));
>>         out_be32(&regs->uaw0, val);
>>
>> -       val = (dev->enetaddr[5] << 8) | dev->enetaddr[4] ;
>> +       val = (pdata->enetaddr[5] << 8) | pdata->enetaddr[4];
>>         val |= in_be32(&regs->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK;
>>         out_be32(&regs->uaw1, val);
>>         return 0;
>> @@ -396,10 +402,10 @@ static void axi_dma_init(struct axidma_priv *priv)
>>                 printf("%s: Timeout\n", __func__);
>>  }
>>
>> -static int axiemac_init(struct eth_device *dev, bd_t * bis)
>> +static int axiemac_init(struct udevice *dev)
>>  {
>> -       struct axidma_priv *priv = dev->priv;
>> -       struct axi_regs *regs = (struct axi_regs *)dev->iobase;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>> +       struct axi_regs *regs = priv->iobase;
>>         u32 temp;
>>
>>         debug("axiemac: Init started\n");
>> @@ -458,9 +464,9 @@ static int axiemac_init(struct eth_device *dev, bd_t * bis)
>>         return 0;
>>  }
>>
>> -static int axiemac_send(struct eth_device *dev, void *ptr, int len)
>> +static int axiemac_send(struct udevice *dev, void *ptr, int len)
>>  {
>> -       struct axidma_priv *priv = dev->priv;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>>         u32 timeout;
>>
>>         if (len > PKTSIZE_ALIGN)
>> @@ -530,15 +536,15 @@ static int isrxready(struct axidma_priv *priv)
>>         return 0;
>>  }
>>
>> -static int axiemac_recv(struct eth_device *dev)
>> +static int axiemac_recv(struct udevice *dev, int flags, uchar **packetp)
>>  {
>>         u32 length;
>> -       struct axidma_priv *priv = dev->priv;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>>         u32 temp;
>>
>>         /* Wait for an incoming packet */
>>         if (!isrxready(priv))
>> -               return 0;
>> +               return -1;
>>
>>         debug("axiemac: RX data ready\n");
>>
>> @@ -578,77 +584,125 @@ static int axiemac_recv(struct eth_device *dev)
>>
>>         debug("axiemac: RX completed, framelength = %d\n", length);
>>
>> -       return length;
>> +       return 0;
>>  }
>>
>> -static int axiemac_miiphy_read(const char *devname, uchar addr,
>> -                                                       uchar reg, ushort *val)
>> +static int axiemac_miiphy_read(struct mii_dev *bus, int addr,
>> +                              int devad, int reg)
>>  {
>> -       struct eth_device *dev = eth_get_dev();
>> -       u32 ret;
>> +       int ret;
>> +       u16 value;
>>
>> -       ret = phyread(dev->priv, addr, reg, val);
>> -       debug("axiemac: Read MII 0x%x, 0x%x, 0x%x\n", addr, reg, *val);
>> -       return ret;
>> +       ret = phyread(bus->priv, addr, reg, &value);
>> +       debug("axiemac: Read MII 0x%x, 0x%x, 0x%x, %d\n", addr, reg,
>> +             value, ret);
>> +       return value;
>>  }
>>
>> -static int axiemac_miiphy_write(const char *devname, uchar addr,
>> -                                                       uchar reg, ushort val)
>> +static int axiemac_miiphy_write(struct mii_dev *bus, int addr, int devad,
>> +                               int reg, u16 value)
>>  {
>> -       struct eth_device *dev = eth_get_dev();
>> -
>> -       debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, val);
>> -       return phywrite(dev->priv, addr, reg, val);
>> +       debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, value);
>> +       return phywrite(bus->priv, addr, reg, value);
>>  }
>>
>> -static int axiemac_bus_reset(struct mii_dev *bus)
>> +static int axi_emac_probe(struct udevice *dev)
>>  {
>> -       debug("axiemac: Bus reset\n");
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>> +       int ret;
>> +
>> +       priv->bus = mdio_alloc();
>> +       priv->bus->read = axiemac_miiphy_read;
>> +       priv->bus->write = axiemac_miiphy_write;
>> +       priv->bus->priv = priv;
>> +       strcpy(priv->bus->name, "axi_emac");
>> +
>> +       ret = mdio_register(priv->bus);
>> +       if (ret)
>> +               return ret;
>> +
>>         return 0;
>>  }
>>
>> -int xilinx_axiemac_initialize(bd_t *bis, unsigned long base_addr,
>> -                                                       unsigned long dma_addr)
>> +static int axi_emac_remove(struct udevice *dev)
>>  {
>> -       struct eth_device *dev;
>> -       struct axidma_priv *priv;
>> +       struct axidma_priv *priv = dev_get_priv(dev);
>>
>> -       dev = calloc(1, sizeof(struct eth_device));
>> -       if (dev == NULL)
>> -               return -1;
>> +       free(priv->phydev);
>> +       mdio_unregister(priv->bus);
>> +       mdio_free(priv->bus);
>>
>> -       dev->priv = calloc(1, sizeof(struct axidma_priv));
>> -       if (dev->priv == NULL) {
>> -               free(dev);
>> -               return -1;
>> -       }
>> -       priv = dev->priv;
>> +       return 0;
>> +}
>>
>> -       sprintf(dev->name, "aximac.%lx", base_addr);
>> +static const struct eth_ops axi_emac_ops = {
>> +       .start                  = axiemac_init,
> 
> Now would be a good time to rename the driver function start.
> 
>> +       .send                   = axiemac_send,
>> +       .recv                   = axiemac_recv,
>> +       .stop                   = axiemac_halt,
> 
> Now would be a good time to rename the driver function stop.
> 
>> +       .write_hwaddr           = axiemac_setup_mac,
> 
> It would be good to call this axiemac_write_hwaddr.

Will be in separate patch.

Thanks,
Michal



More information about the U-Boot mailing list