[U-Boot] [PATCH v3 1/4] mips: add base support for atheros ath79 based SOCs
Wills Wang
wills.wang at live.com
Thu Dec 24 14:51:06 CET 2015
On 12/24/2015 07:52 PM, Marek Vasut wrote:
> On Thursday, December 24, 2015 at 12:22:00 PM, Wills Wang wrote:
>> This patch enable work for ar933x SOC, tested on ar9331 board.
>>
>> Signed-off-by: Wills Wang <wills.wang at live.com>
> [...]
>
>> diff --git a/arch/mips/config.mk b/arch/mips/config.mk
>> index 3ebc202..fd50909 100644
>> --- a/arch/mips/config.mk
>> +++ b/arch/mips/config.mk
>> @@ -39,6 +39,7 @@ cpuflags-$(CONFIG_CPU_MIPS32_R1) += -march=mips32
>> -Wa,-mips32 cpuflags-$(CONFIG_CPU_MIPS32_R2) += -march=mips32r2
>> -Wa,-mips32r2 cpuflags-$(CONFIG_CPU_MIPS64_R1) += -march=mips64
>> -Wa,-mips64
>> cpuflags-$(CONFIG_CPU_MIPS64_R2) += -march=mips64r2 -Wa,-mips64r2
>> +cpuflags-$(CONFIG_ARCH_ATH79) += -mtune=24kc
> You can just tune it for MIPS32_R2 , it will be compatible with older toolchains
> too. I don't think there is much benefit in being so explicit and using mips24kc
> tuning.
>
>> PLATFORM_CPPFLAGS += $(cpuflags-y)
>>
>> PLATFORM_CPPFLAGS += -D__MIPS__
> [...]
>
>> diff --git a/arch/mips/mach-ath79/ar933x/ddr_tap.S
>> b/arch/mips/mach-ath79/ar933x/ddr_tap.S new file mode 100644
>> index 0000000..18c57de
>> --- /dev/null
>> +++ b/arch/mips/mach-ath79/ar933x/ddr_tap.S
>> @@ -0,0 +1,268 @@
>> +/*
>> + * (C) Copyright 2015
>> + * Wills Wang, <wills.wang at live.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <config.h>
>> +#include <asm/asm.h>
>> +#include <asm/regdef.h>
>> +#include <asm/mipsregs.h>
>> +#include <asm/addrspace.h>
>> +#include <asm/arch/ar71xx_regs.h>
>> +
>> +#define DRAM_K0(x) KSEG0ADDR(x)
>> +#define DRAM_K1(x) KSEG1ADDR(x)
>> +
>> + .text
>> + .set noreorder
>> +
>> +LEAF(ddr_tap_init)
>> + /* Tap settings for the DDR */
>> + li t0, 0xffffffff
>> + li t1, DRAM_K0(0x500000)
>> + sw t0, 0x0(t1)
>> + sw t0, 0x4(t1)
>> + sw t0, 0x8(t1)
>> + sw t0, 0xc(t1)
>> + nop
>> + nop
>> +
>> + li t8, DRAM_K1(0x2000)
>> + li t0, 0x00
>> + li t1, 0x100
>> +0:
>> + andi t2, t0, 0x03
>> + li t3, 0x00
>> + bne t2, t3,1f
>> + nop
>> + li t9, 0x00000000
>> + sw t9, 0x0(t8)
>> + b 2f
>> + nop
> Please rewrite this into C, I believe it should be pretty easy.
>
> [...]
>
>> diff --git a/arch/mips/mach-ath79/ar933x/lowlevel_init.S
>> b/arch/mips/mach-ath79/ar933x/lowlevel_init.S new file mode 100644
>> index 0000000..72509ca
>> --- /dev/null
>> +++ b/arch/mips/mach-ath79/ar933x/lowlevel_init.S
>> @@ -0,0 +1,460 @@
>> +/*
>> + * (C) Copyright 2015
>> + * Wills Wang, <wills.wang at live.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <config.h>
>> +#include <asm/asm.h>
>> +#include <asm/regdef.h>
>> +#include <asm/mipsregs.h>
>> +#include <asm/addrspace.h>
>> +#include <asm/arch/ar71xx_regs.h>
>> +
>> +#define SET_BIT(val, bit) ((val) | (1 << (bit)))
>> +#define SET_PLL_PD(val) SET_BIT(val, 30)
>> +#define AHB_DIV_TO_4(val) SET_BIT(SET_BIT(val, 15), 16)
>> +#define PLL_BYPASS(val) SET_BIT(val, 2)
>> +
>> +#define MK_PLL_CONF(divint, refdiv, range, outdiv) \
>> + (((0x3F & divint) << 10) | \
>> + ((0x1F & refdiv) << 16) | \
>> + ((0x1 & range) << 21) | \
>> + ((0x7 & outdiv) << 23) )
>> +
>> +#define MK_CLK_CNTL(cpudiv, ddrdiv, ahbdiv) \
>> + (((0x3 & (cpudiv - 1)) << 5) | \
>> + ((0x3 & (ddrdiv - 1)) << 10) | \
>> + ((0x3 & (ahbdiv - 1)) << 15) )
>> +
>> +/*
>> + * PLL_CPU_CONFIG_VAL
>> + *
>> + * Bit30 is set (CPU_PLLPWD = 1 -> power down control for CPU PLL)
>> + * After PLL configuration we need to clear this bit
>> + *
>> + * Values written into CPU PLL Configuration (CPU_PLL_CONFIG)
>> + *
>> + * bits 10..15 (6bit) DIV_INT (Integer part of the DIV to CPU PLL)
>> + * => 32 (0x20) VCOOUT = XTAL * DIV_INT
>> + * bits 16..20 (5bit) REFDIV (Reference clock divider)
>> + * => 1 (0x1) [Must start at values 1]
>> + * bits 21 (1bit) RANGE (VCO frequency range of the CPU PLL)
>> + * => 0 (0x0) [Doesn't impact clock values]
>> + * bits 23..25 (3bit) OUTDIV (Ratio between VCO and PLL output)
>> + * => 1 (0x1) [0 is illegal!]
>> + * PLLOUT = VCOOUT * (1/2^OUTDIV)
>> + */
>> +/* DIV_INT=32 (25MHz*32/2=400MHz), REFDIV=1, RANGE=0, OUTDIV=1 */
>> +#define PLL_CPU_CONFIG_VAL_40M MK_PLL_CONF(20, 1, 0, 1)
>> +/* DIV_INT=20 (40MHz*20/2=400MHz), REFDIV=1, RANGE=0, OUTDIV=1 */
>> +#define PLL_CPU_CONFIG_VAL_25M MK_PLL_CONF(32, 1, 0, 1)
>> +
>> +/*
>> + * PLL_CLK_CONTROL_VAL
>> + *
>> + * In PLL_CLK_CONTROL_VAL bit 2 is set (BYPASS = 1 -> bypass PLL)
>> + * After PLL configuration we need to clear this bit
>> + *
>> + * Values written into CPU Clock Control Register CLOCK_CONTROL
>> + *
>> + * bits 2 (1bit) BYPASS (Bypass PLL. This defaults to 1 for test.
>> + * Software must enable the CPU PLL for normal and
>> + * then set this bit to 0)
>> + * bits 5..6 (2bit) CPU_POST_DIV => 0 (DEFAULT, Ratio = 1)
>> + * CPU_CLK = PLLOUT / CPU_POST_DIV
>> + * bits 10..11 (2bit) DDR_POST_DIV => 0 (DEFAULT, Ratio = 1)
>> + * DDR_CLK = PLLOUT / DDR_POST_DIV
>> + * bits 15..16 (2bit) AHB_POST_DIV => 1 (DEFAULT, Ratio = 2)
>> + * AHB_CLK = PLLOUT / AHB_POST_DIV
>> + *
>> + */
>> +#define PLL_CLK_CONTROL_VAL MK_CLK_CNTL(1, 1, 2)
>> +
>> + .text
>> + .set noreorder
>> +
>> +LEAF(lowlevel_init)
>> + /* These three WLAN_RESET will avoid original issue */
>> + li t3, 0x03
>> +1:
>> + li t0, KSEG1ADDR(AR71XX_RESET_BASE)
>> + lw t1, AR933X_RESET_REG_RESET_MODULE(t0)
>> + ori t1, t1, 0x0800
>> + sw t1, AR933X_RESET_REG_RESET_MODULE(t0)
>> + nop
>> + lw t1, AR933X_RESET_REG_RESET_MODULE(t0)
>> + li t2, 0xfffff7ff
>> + and t1, t1, t2
>> + sw t1, AR933X_RESET_REG_RESET_MODULE(t0)
>> + nop
>> + addi t3, t3, -1
>> + bnez t3, 1b
>> + nop
> This should be also easy to rewrite into C , right ?
C runtime environment is not available.
C stack is not ready before DDR has initialized.
>
> [...]
>
>> diff --git a/arch/mips/mach-ath79/cpu.c b/arch/mips/mach-ath79/cpu.c
>> new file mode 100644
>> index 0000000..1f58877
>> --- /dev/null
>> +++ b/arch/mips/mach-ath79/cpu.c
>> @@ -0,0 +1,269 @@
>> +/*
>> + * (C) Copyright 2015
>> + * Wills Wang, <wills.wang at live.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include <asm/addrspace.h>
>> +#include <asm/types.h>
>> +#include <asm/arch/ath79.h>
>> +#include <asm/arch/ar71xx_regs.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +enum ath79_soc_type get_soc_type(void)
>> +{
>> + enum ath79_soc_type soc = ATH79_SOC_UNKNOWN;
>> + u32 id, major, minor;
>> +
>> + id = readl(KSEG1ADDR(AR71XX_RESET_BASE + AR71XX_RESET_REG_REV_ID));
>> + major = id & REV_ID_MAJOR_MASK;
>> +
>> + switch (major) {
>> + case REV_ID_MAJOR_AR71XX:
>> + minor = id & AR71XX_REV_ID_MINOR_MASK;
>> + switch (minor) {
>> + case AR71XX_REV_ID_MINOR_AR7130:
>> + soc = ATH79_SOC_AR7130;
>> + break;
> I think you can convert this stuff into a table of sorts, so you won't have
> such a lengthy code:
>
> struct {
> u32 major;
> u32 minor;
> enum soc;
> } table[] {
> { REV_ID_MAJOR_AR71XX, AR71XX_REV_ID_MINOR_AR7130, ATH79_SOC_AR7130 },
> ...
> }
>
> And just iterate over such table.
>
> [...]
>
>> +int print_cpuinfo(void)
>> +{
>> + enum ath79_soc_type soc = ATH79_SOC_UNKNOWN;
>> + char *chip = "????";
>> + u32 id, major, minor;
>> + u32 rev = 0;
>> + u32 ver = 1;
>> +
>> + id = readl(KSEG1ADDR(AR71XX_RESET_BASE + AR71XX_RESET_REG_REV_ID));
>> + major = id & REV_ID_MAJOR_MASK;
>> +
>> + switch (major) {
>> + case REV_ID_MAJOR_AR71XX:
>> + minor = id & AR71XX_REV_ID_MINOR_MASK;
>> + rev = id >> AR71XX_REV_ID_REVISION_SHIFT;
>> + rev &= AR71XX_REV_ID_REVISION_MASK;
>> + switch (minor) {
>> + case AR71XX_REV_ID_MINOR_AR7130:
>> + soc = ATH79_SOC_AR7130;
>> + chip = "7130";
>> + break;
> DTTO here, use table lookup
>
> [...]
>
>> +
>> + return 0;
>> +}
>> diff --git a/arch/mips/mach-ath79/dram.c b/arch/mips/mach-ath79/dram.c
>> new file mode 100644
>> index 0000000..42539dc
>> --- /dev/null
>> +++ b/arch/mips/mach-ath79/dram.c
>> @@ -0,0 +1,27 @@
>> +/*
>> + * (C) Copyright 2015
>> + * Wills Wang, <wills.wang at live.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/addrspace.h>
>> +#include <asm/arch/ddr.h>
>> +
>> +phys_size_t initdram(int board_type)
>> +{
>> + uint8_t *addr, *p;
>> + int i;
>> +
>> + ddr_tap_init();
>> + addr = (uint8_t *)KSEG1;
>> + *addr = 0x77;
>> + for (i = 0, p = addr; p < (uint8_t *)KSEG2; i++) {
>> + p += 0x1000000;
>> + *p = i;
>> + if (*addr != 0x77)
>> + break;
>> + }
> What is this and how does it work ?
Physical memory was mapped circularly for this chip.
>
>> + return (phys_size_t)(p - addr);
>> +}
> [...]
>
>> diff --git a/arch/mips/mach-ath79/reset.c b/arch/mips/mach-ath79/reset.c
>> new file mode 100644
>> index 0000000..0ace05d
>> --- /dev/null
>> +++ b/arch/mips/mach-ath79/reset.c
>> @@ -0,0 +1,55 @@
>> +/*
>> + * (C) Copyright 2015
>> + * Wills Wang, <wills.wang at live.com>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include <asm/addrspace.h>
>> +#include <asm/types.h>
>> +#include <asm/arch/ath79.h>
>> +#include <asm/arch/ar71xx_regs.h>
>> +
>> +#define REG_READ(b, o) readl(KSEG1ADDR(b + o))
>> +#define REG_WRITE(b, o, v) writel(v, KSEG1ADDR((b + o)))
>> +#define RST_READ(a) REG_READ(AR71XX_RESET_BASE, a)
>> +#define RST_WRITE(a, v) REG_WRITE(AR71XX_RESET_BASE, a, v)
> Drop these.
>
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +void _machine_restart(void)
>> +{
>> + enum ath79_soc_type soc;
>> + u32 val, reg = 0;
>> +
>> + soc = get_soc_type();
>> + if (soc_is_ar71xx(soc))
>> + reg = AR71XX_RESET_REG_RESET_MODULE;
>> + else if (soc_is_ar724x(soc))
>> + reg = AR724X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_ar913x(soc))
>> + reg = AR913X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_ar933x(soc))
>> + reg = AR933X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_ar934x(soc))
>> + reg = AR934X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_qca953x(soc))
>> + reg = QCA953X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_qca955x(soc))
>> + reg = QCA955X_RESET_REG_RESET_MODULE;
>> + else if (soc_is_qca956x(soc))
>> + reg = QCA956X_RESET_REG_RESET_MODULE;
>> + else
>> + puts("Reset register not defined for this SOC\n");
>> +
>> + if (reg) {
>> + val = RST_READ(reg);
>> + val |= AR71XX_RESET_FULL_CHIP;
>> + RST_WRITE(reg, val);
> setbits_le32() please.
Macro setbits_le32() is not available for MIPS architecture.
Other, I don't think there is better in being so explicit and using
little-endian.
>> + }
>> +
>> + while (1)
>> + /* NOP */;
>> +}
>
More information about the U-Boot
mailing list