[U-Boot] [PATCH] mx25: Fix relocation by adding specific relocate_vectors

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam at freescale.com>

Since commit ("arm: relocate the exception vectors") mx25pdk hangs like this:

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: WDOG
Board: MX25PDK
I2C:   ready
DRAM:  64 MiB
(hangs)

We need to add a specific relocate_vectors macro, just like it was done for
mx27 SoC in commit db544b9662622826b8 ("imx: fix exception vectors relocation
in imx27").

This allows mx25 to boot again.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
 arch/arm/cpu/arm926ejs/mx25/Makefile   |  4 +++
 arch/arm/cpu/arm926ejs/mx25/relocate.S | 51 ++++++++++++++++++++++++++++++++++
 2 files changed, 55 insertions(+)
 create mode 100644 arch/arm/cpu/arm926ejs/mx25/relocate.S

diff --git a/arch/arm/cpu/arm926ejs/mx25/Makefile b/arch/arm/cpu/arm926ejs/mx25/Makefile
index 134c69d..ebc0407 100644
--- a/arch/arm/cpu/arm926ejs/mx25/Makefile
+++ b/arch/arm/cpu/arm926ejs/mx25/Makefile
@@ -5,3 +5,7 @@
 # SPDX-License-Identifier:	GPL-2.0+
 
 obj-y	= generic.o timer.o reset.o
+
+ifndef CONFIG_SPL_BUILD
+obj-y	+= relocate.o
+endif
diff --git a/arch/arm/cpu/arm926ejs/mx25/relocate.S b/arch/arm/cpu/arm926ejs/mx25/relocate.S
new file mode 100644
index 0000000..e0dfdee
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/mx25/relocate.S
@@ -0,0 +1,51 @@
+/*
+ *  relocate - i.MX25-specific vector relocation
+ *
+ *  Copyright (c) 2013  Albert ARIBAUD <albert.u.boot at aribaud.net>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <linux/linkage.h>
+
+/*
+ * The i.MX25 SoC is very specific with respect to exceptions: it
+ * does not provide RAM at the high vectors address (0xFFFF0000),
+ * thus only the low address (0x00000000) is useable; but that is
+ * in ROM. Therefore, vectors cannot be changed at all.
+ *
+ * However, these ROM-based vectors actually just perform indirect
+ * calls through pointers located in RAM at SoC-specific addresses,
+ * as follows:
+ *
+ * Offset      Exception              Use by ROM code
+ * 0x00000000  reset                  indirect branch to [0x00000014]
+ * 0x00000004  undefined instruction  indirect branch to [0xfffffef0]
+ * 0x00000008  software interrupt     indirect branch to [0xfffffef4]
+ * 0x0000000c  prefetch abort         indirect branch to [0xfffffef8]
+ * 0x00000010  data abort             indirect branch to [0xfffffefc]
+ * 0x00000014  (reserved in ARMv5)    vector to ROM reset: 0xc0000000
+ * 0x00000018  IRQ                    indirect branch to [0xffffff00]
+ * 0x0000001c  FIQ                    indirect branch to [0xffffff04]
+ *
+ * In order to initialize exceptions on i.MX25, we must copy U-Boot's
+ * indirect (not exception!) vector table into 0xfffffef0..0xffffff04
+ * taking care not to copy vectors number 5 (reserved exception).
+ */
+
+	.section	.text.relocate_vectors,"ax",%progbits
+
+ENTRY(relocate_vectors)
+
+	ldr	r0, [r9, #GD_RELOCADDR]	/* r0 = gd->relocaddr */
+	ldr	r1, =32			/* size of vector table */
+	add	r0, r0, r1		/* skip to indirect table */
+	ldr	r1, =0xFFFFFEF0		/* i.MX25 indirect table */
+	ldmia	r0!, {r2-r8}		/* load indirect vectors 1..7 */
+	stmia	r1!, {r2-r5, r7,r8}	/* write all but vector 5 */
+
+	bx	lr
+
+ENDPROC(relocate_vectors)
-- 
1.9.1