[U-Boot] [PATCH 10/22] ppc4xx: remove HUB405 board

Matthias Fuchs matthias.fuchs at esd.eu
Mon Jan 12 22:47:23 CET 2015


Signed-off-by: Matthias Fuchs <matthias.fuchs at esd.eu>
---
 arch/powerpc/cpu/ppc4xx/Kconfig |    4 -
 board/esd/hub405/Kconfig        |   12 --
 board/esd/hub405/MAINTAINERS    |    6 -
 board/esd/hub405/Makefile       |   10 --
 board/esd/hub405/flash.c        |   85 ----------
 board/esd/hub405/hub405.c       |  208 -----------------------
 configs/HUB405_defconfig        |    3 -
 doc/README.scrapyard            |    1 +
 include/configs/HUB405.h        |  351 ---------------------------------------
 9 files changed, 1 insertion(+), 679 deletions(-)
 delete mode 100644 board/esd/hub405/Kconfig
 delete mode 100644 board/esd/hub405/MAINTAINERS
 delete mode 100644 board/esd/hub405/Makefile
 delete mode 100644 board/esd/hub405/flash.c
 delete mode 100644 board/esd/hub405/hub405.c
 delete mode 100644 configs/HUB405_defconfig
 delete mode 100644 include/configs/HUB405.h

diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig
index 8ce66d6..cab8f25 100644
--- a/arch/powerpc/cpu/ppc4xx/Kconfig
+++ b/arch/powerpc/cpu/ppc4xx/Kconfig
@@ -125,9 +125,6 @@ config TARGET_CPCI405AB
 config TARGET_CPCI405DT
 	bool "Support CPCI405DT"
 
-config TARGET_HUB405
-	bool "Support HUB405"
-
 config TARGET_OCRTC
 	bool "Support OCRTC"
 
@@ -232,7 +229,6 @@ source "board/csb472/Kconfig"
 source "board/dave/PPChameleonEVB/Kconfig"
 source "board/esd/cpci2dp/Kconfig"
 source "board/esd/cpci405/Kconfig"
-source "board/esd/hub405/Kconfig"
 source "board/esd/ocrtc/Kconfig"
 source "board/esd/pci405/Kconfig"
 source "board/esd/plu405/Kconfig"
diff --git a/board/esd/hub405/Kconfig b/board/esd/hub405/Kconfig
deleted file mode 100644
index 2b9556a..0000000
--- a/board/esd/hub405/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_HUB405
-
-config SYS_BOARD
-	default "hub405"
-
-config SYS_VENDOR
-	default "esd"
-
-config SYS_CONFIG_NAME
-	default "HUB405"
-
-endif
diff --git a/board/esd/hub405/MAINTAINERS b/board/esd/hub405/MAINTAINERS
deleted file mode 100644
index e84a1d9..0000000
--- a/board/esd/hub405/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-HUB405 BOARD
-M:	Matthias Fuchs <matthias.fuchs at esd-electronics.com>
-S:	Maintained
-F:	board/esd/hub405/
-F:	include/configs/HUB405.h
-F:	configs/HUB405_defconfig
diff --git a/board/esd/hub405/Makefile b/board/esd/hub405/Makefile
deleted file mode 100644
index 99e18b5..0000000
--- a/board/esd/hub405/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= hub405.o flash.o \
-	../common/misc.o \
-	../common/esd405ep_nand.o \
diff --git a/board/esd/hub405/flash.c b/board/esd/hub405/flash.c
deleted file mode 100644
index 23e8164..0000000
--- a/board/esd/hub405/flash.c
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * (C) Copyright 2001
- * Stefan Roese, esd gmbh germany, stefan.roese at esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-
-/*
- * include common flash code (for esd boards)
- */
-#include "../common/flash.c"
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size_b0;
-	int i;
-	uint pbcr;
-	unsigned long base_b0;
-	int size_val = 0;
-
-	/* Init: no FLASHes known */
-	for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size_b0, size_b0<<20);
-	}
-
-	/* Setup offsets */
-	flash_get_offsets (-size_b0, &flash_info[0]);
-
-	/* Re-do sizing to get full correct info */
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	base_b0 = -size_b0;
-	switch (size_b0) {
-	case 1 << 20:
-		size_val = 0;
-		break;
-	case 2 << 20:
-		size_val = 1;
-		break;
-	case 4 << 20:
-		size_val = 2;
-		break;
-	case 8 << 20:
-		size_val = 3;
-		break;
-	case 16 << 20:
-		size_val = 4;
-		break;
-	}
-	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(EBC0_CFGDATA, pbcr);
-
-	/* Monitor protection ON by default */
-	(void)flash_protect(FLAG_PROTECT_SET,
-			    -CONFIG_SYS_MONITOR_LEN,
-			    0xffffffff,
-			    &flash_info[0]);
-
-	flash_info[0].size = size_b0;
-
-	return (size_b0);
-}
diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c
deleted file mode 100644
index 1423744..0000000
--- a/board/esd/hub405/hub405.c
+++ /dev/null
@@ -1,208 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese at esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <command.h>
-#include <malloc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern void lxt971_no_sleep(void);
-
-int board_revision(void)
-{
-	unsigned long osrl_reg;
-	unsigned long isr1l_reg;
-	unsigned long tcr_reg;
-	unsigned long value;
-
-	/*
-	 * Get version of HUB405 board from GPIO's
-	 */
-
-	/*
-	 * Setup GPIO pin(s) (IRQ6/GPIO23)
-	 */
-	osrl_reg = in_be32((void *)GPIO0_OSRH);
-	isr1l_reg = in_be32((void *)GPIO0_ISR1H);
-	tcr_reg = in_be32((void *)GPIO0_TCR);
-	out_be32((void *)GPIO0_OSRH, osrl_reg & ~0x00030000);     /* output select */
-	out_be32((void *)GPIO0_ISR1H, isr1l_reg | 0x00030000);    /* input select  */
-	out_be32((void *)GPIO0_TCR, tcr_reg & ~0x00000100);       /* select input  */
-
-	udelay(1000);            /* wait some time before reading input */
-	value = in_be32((void *)GPIO0_IR) & 0x00000100;         /* get config bits */
-
-	/*
-	 * Restore GPIO settings
-	 */
-	out_be32((void *)GPIO0_OSRH, osrl_reg);                   /* output select */
-	out_be32((void *)GPIO0_ISR1H, isr1l_reg);                 /* input select  */
-	out_be32((void *)GPIO0_TCR, tcr_reg);  /* enable output driver for outputs */
-
-	if (value & 0x00000100) {
-		/* Revision 1.1 or 1.2 detected */
-		return 1;
-	}
-
-	/* Revision 1.0 */
-	return 0;
-}
-
-
-int board_early_init_f (void)
-{
-	/*
-	 * IRQ 0-15  405GP internally generated; active high; level sensitive
-	 * IRQ 16    405GP internally generated; active low; level sensitive
-	 * IRQ 17-24 RESERVED
-	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
-	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
-	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
-	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
-	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
-	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
-	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
-	 */
-	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(UIC0ER, 0x00000000);       /* disable all ints */
-	mtdcr(UIC0CR, 0x00000000);       /* set all to be non-critical*/
-	mtdcr(UIC0PR, 0xFFFFFF9F);       /* set int polarities */
-	mtdcr(UIC0TR, 0x10000000);       /* set int trigger levels */
-	mtdcr(UIC0VCR, 0x00000001);      /* set vect base=0,INT0 highest priority*/
-	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
-
-	/*
-	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
-	 */
-	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
-
-	return 0;
-}
-
-#define LED_REG (DUART0_BA + 0x20)
-int misc_init_r (void)
-{
-	unsigned long val;
-	int delay, flashcnt;
-	char *str;
-	char hw_rev[4];
-
-	/*
-	 * Enable interrupts in exar duart mcr[3]
-	 */
-	out_8((void *)(DUART0_BA + 4), 0x08);
-	out_8((void *)(DUART1_BA + 4), 0x08);
-	out_8((void *)(DUART2_BA + 4), 0x08);
-	out_8((void *)(DUART3_BA + 4), 0x08);
-
-	/*
-	 * Set RS232/RS422 control (RS232 = high on GPIO)
-	 */
-	val = in_be32((void *)GPIO0_OR);
-	val &= ~(CONFIG_SYS_UART2_RS232 | CONFIG_SYS_UART3_RS232 |
-		 CONFIG_SYS_UART4_RS232 | CONFIG_SYS_UART5_RS232);
-
-	str = getenv("phys0");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART2_RS232;
-
-	str = getenv("phys1");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART3_RS232;
-
-	str = getenv("phys2");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART4_RS232;
-
-	str = getenv("phys3");
-	if (!str || (str && (str[0] == '0')))
-		val |= CONFIG_SYS_UART5_RS232;
-
-	out_be32((void *)GPIO0_OR, val);
-
-	/*
-	 * check board type and setup AP power
-	 */
-	str = getenv("bd_type"); /* this is only set on non prototype hardware */
-	if (str != NULL) {
-		if ((strcmp(str, "swch405") == 0) || ((!strcmp(str, "hub405") && (gd->board_type >= 1)))) {
-			unsigned char led_reg_default = 0;
-			str = getenv("ap_pwr");
-			if (!str || (str && (str[0] == '1')))
-				led_reg_default = 0x04 | 0x02 ; /* U2_LED | AP_PWR */
-
-			/*
-			 * Flash LEDs
-			 */
-			for (flashcnt = 0; flashcnt < 3; flashcnt++) {
-				/* LED_A..D off */
-				out_8((void *)LED_REG, led_reg_default);
-				for (delay = 0; delay < 100; delay++)
-					udelay(1000);
-				/* LED_A..D on */
-				out_8((void *)LED_REG, led_reg_default | 0xf0);
-				for (delay = 0; delay < 50; delay++)
-					udelay(1000);
-			}
-			out_8((void *)LED_REG, led_reg_default);
-		}
-	}
-
-	/*
-	 * Reset external DUARTs
-	 */
-	out_be32((void *)GPIO0_OR,
-		 in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */
-	udelay(10); /* wait 10us */
-	out_be32((void *)GPIO0_OR,
-		 in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */
-	udelay(1000); /* wait 1ms */
-
-	/*
-	 * Store hardware revision in environment for further processing
-	 */
-	sprintf(hw_rev, "1.%ld", gd->board_type);
-	setenv("hw_rev", hw_rev);
-	return (0);
-}
-
-
-/*
- * Check Board Identity:
- */
-int checkboard (void)
-{
-	char str[64];
-	int i = getenv_f("serial#", str, sizeof(str));
-
-	puts ("Board: ");
-
-	if (i == -1) {
-		puts ("### No HW ID - assuming HUB405");
-	} else {
-		puts(str);
-	}
-
-	if (getenv_f("bd_type", str, sizeof(str)) != -1) {
-		printf(" (%s", str);
-	} else {
-		puts(" (Missing bd_type!");
-	}
-
-	gd->board_type = board_revision();
-	printf(", Rev 1.%ld)\n", gd->board_type);
-
-	/*
-	 * Disable sleep mode in LXT971
-	 */
-	lxt971_no_sleep();
-
-	return 0;
-}
diff --git a/configs/HUB405_defconfig b/configs/HUB405_defconfig
deleted file mode 100644
index a39712e..0000000
--- a/configs/HUB405_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_HUB405=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 1775987..d8bb3aa 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+HUB405           ppc4xx      405ep          -           -           Matthias Fuchs <matthias.fuchs at esd.eu>
 HH405            ppc4xx      405ep          -           -           Matthias Fuchs <matthias.fuchs at esd.eu>
 DU440            ppc4xx      440epx         -           -           Matthias Fuchs <matthias.fuchs at esd.eu>
 DU405            ppc4xx      405gpr         -           -           Matthias Fuchs <matthias.fuchs at esd.eu>
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
deleted file mode 100644
index 1783b9f..0000000
--- a/include/configs/HUB405.h
+++ /dev/null
@@ -1,351 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese at esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_HUB405		1	/* ...on a HUB405 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-
-#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-#undef	CONFIG_BOOTARGS
-#undef  CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT                  /* enable preboot variable      */
-
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
-
-#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD	    691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
-
-/* Ethernet stuff */
-#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
-#define CONFIG_ETHADDR	00:50:C2:1E:AF:FE
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
-#define NAND_BIG_DELAY_US	25
-
-#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
-#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
-#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
-
-#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
-#define CONFIG_SYS_NAND_QUIET          1
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
-#define PCI_HOST_FORCE	1		/* configure as pci host	*/
-#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
-
-#undef	CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_HOST PCI_HOST_HOST	/* select pci host function	*/
-#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-					/* resource configuration	*/
-
-#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
-#define CONFIG_SYS_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA	0x00000000	/* point to sdram		*/
-#define CONFIG_SYS_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
-#define CONFIG_SYS_PCI_PTM2LA	0xffc00000	/* point to flash		*/
-#define CONFIG_SYS_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
-#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
-#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
-#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
-#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-
-#if 0 /* test-only */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CONFIG_SYS_NVRAM_SIZE		242			/* NVRAM size		*/
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB0AP		0x92015480
-/*#define CONFIG_SYS_EBC_PB0AP		  0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB1AP		0x92015480
-#define CONFIG_SYS_EBC_PB1CR		0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit	*/
-
-/* Memory Bank 2 (8 Bit Peripheral: UART) initialization			*/
-#if 0
-#define CONFIG_SYS_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
-#else
-#define CONFIG_SYS_EBC_PB2AP		0x92015480
-#define CONFIG_SYS_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
-#endif
-
-#define DUART0_BA	0xF0000000	    /* DUART Base Address		*/
-#define DUART1_BA	0xF0000008	    /* DUART Base Address		*/
-#define DUART2_BA	0xF0000010	    /* DUART Base Address		*/
-#define DUART3_BA	0xF0000018	    /* DUART Base Address		*/
-#define CONFIG_SYS_NAND_BASE	0xF4000000
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-#define CONFIG_SYS_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
-#define CONFIG_SYS_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
-#define CONFIG_SYS_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
-#define CONFIG_SYS_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
-#define CONFIG_SYS_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM	  1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0]	- External Bus Controller BLAST output
- * GPIO0[1-9]	- Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- */
-#define CONFIG_SYS_GPIO0_OSRL		0x40000550
-#define CONFIG_SYS_GPIO0_OSRH		0x00000110
-#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
-#define CONFIG_SYS_GPIO0_ISR1H		0x15555445
-#define CONFIG_SYS_GPIO0_TSRL		0x00000000
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000
-#define CONFIG_SYS_GPIO0_TCR		0xF7FE0014
-
-#define CONFIG_SYS_DUART_RST           (0x80000000 >> 14)
-#define CONFIG_SYS_UART2_RS232         (0x80000000 >> 5)
-#define CONFIG_SYS_UART3_RS232         (0x80000000 >> 6)
-#define CONFIG_SYS_UART4_RS232         (0x80000000 >> 7)
-#define CONFIG_SYS_UART5_RS232         (0x80000000 >> 8)
-
-/*
- * Default speed selection (cpu_plb_opb_ebc) in mhz.
- * This value will be set if iic boot eprom is disabled.
- */
-#if 0
-#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
-#endif
-#if 0
-#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
-#endif
-#if 1
-#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
-#endif
-
-#endif	/* __CONFIG_H */
-- 
1.7.9.5



More information about the U-Boot mailing list