[U-Boot] [PATCH 2/3] pmic:pfuze implement pmic_mode_init

[Peng Fan]

Hi, Przemyslaw

On 1/15/2015 5:00 PM, Przemyslaw Marczak wrote:
> Hello Peg,
>
> On 01/08/2015 02:00 PM, Peng Fan wrote:
>> This patch is to implement pmic_mode_init function, and add prototype
>> in header file.
>>
>> This function is to set switching mode for pmic buck regulators to
>> improve system efficiency.
>>
>> Mode:
>> OFF: The regulator is switched off and the output voltage is discharged.
>> PFM: In this mode, the regulator is always in PFM mode, which
>>       is useful at light loads for optimized efficiency.
>> PWM: In this mode, the regulator is always in PWM mode operation
>>       regardless of load conditions.
>> APS: In this mode, the regulator moves automatically between
>>       pulse skipping mode and PWM mode depending on load conditions.
>>
>> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
>> ---
>>   board/freescale/common/pfuze.c | 36 
>> ++++++++++++++++++++++++++++++++++++
>>   board/freescale/common/pfuze.h |  1 +
>>   2 files changed, 37 insertions(+)
>>
>> diff --git a/board/freescale/common/pfuze.c 
>> b/board/freescale/common/pfuze.c
>> index 2cd1794..74df69c 100644
>> --- a/board/freescale/common/pfuze.c
>> +++ b/board/freescale/common/pfuze.c
>> @@ -8,6 +8,42 @@
>>   #include <power/pmic.h>
>>   #include <power/pfuze100_pmic.h>
>>
>
> In this function, you set the same operating mode to the all switching 
> regulators, so this will be done for the all boards which will use 
> this pmic call.
> I assume that this is what you want, if not, then maybe adding the 
> regulator number as an argument, could make it more flexible, for the 
> other configurations.
> So what do you think about this?
>
This is a good suggestion that configure each regulator with it's own 
requirement.  I'll add a new function pfuze_regulator_mode_set to set 
each regulator's mode according input parameter, and also keep 
pfuze_mode_init to configure all regulators. I'll sent out v2 patch soon.

>> +int pfuze_mode_init(struct pmic *p, u32 mode)
>> +{
>> +    unsigned char offset, i, switch_num;
>> +    u32 id, ret;
>> +
>> +    pmic_reg_read(p, PFUZE100_DEVICEID, &id);
>> +    id = id & 0xf;
>> +
>> +    if (id == 0) {
>> +        switch_num = 6;
>> +        offset = PFUZE100_SW1CMODE;
>> +    } else if (id == 1) {
>> +        switch_num = 4;
>> +        offset = PFUZE100_SW2MODE;
>> +    } else {
>> +        printf("Not supported, id=%d\n", id);
>> +        return -1;
>> +    }
>> +
>> +    ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
>> +    if (ret < 0) {
>> +        printf("Set SW1AB mode error!\n");
>> +        return ret;
>> +    }
>> +
>> +    for (i = 0; i < switch_num - 1; i++) {
>> +        ret = pmic_reg_write(p, offset + i * 7, mode);
>> +        if (ret < 0) {
>> +            printf("Set switch%x mode error!\n", offset + i * 7);
>> +            return ret;
>> +        }
>> +    }
>> +
>> +    return ret;
>> +}
>> +
>>   struct pmic *pfuze_common_init(unsigned char i2cbus)
>>   {
>>       struct pmic *p;
>> diff --git a/board/freescale/common/pfuze.h 
>> b/board/freescale/common/pfuze.h
>> index 7a4126c..53cfc99 100644
>> --- a/board/freescale/common/pfuze.h
>> +++ b/board/freescale/common/pfuze.h
>> @@ -8,5 +8,6 @@
>>   #define __PFUZE_BOARD_HELPER__
>>
>>   struct pmic *pfuze_common_init(unsigned char i2cbus);
>> +int pfuze_mode_init(struct pmic *p, u32 mode);
>>
>>   #endif
>>
> If you don't need such feature, then you have my ACK.
>
> For the patchset:
> Acked-by: Przemyslaw Marczak <p.marczak at samsung.com>
>
Thanks,
Peng.