[U-Boot] [PATCH 2/8] powerpc: mpc85xx: remove P1_P2_RDB boards
Masahiro Yamada
yamada.m at jp.panasonic.com
Thu Jan 22 16:24:16 CET 2015
These boards are still non-generic boards:
P1011RDB, P1022RDB, P2010RDB, P2020RDB
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
Cc: Poonam Aggrwal <poonam.aggrwal at freescale.com>
---
arch/powerpc/cpu/mpc85xx/Kconfig | 6 -
board/freescale/p1_p2_rdb/Kconfig | 12 -
board/freescale/p1_p2_rdb/MAINTAINERS | 37 --
board/freescale/p1_p2_rdb/Makefile | 30 --
board/freescale/p1_p2_rdb/README | 145 ------
board/freescale/p1_p2_rdb/ddr.c | 221 --------
board/freescale/p1_p2_rdb/law.c | 17 -
board/freescale/p1_p2_rdb/p1_p2_rdb.c | 303 -----------
board/freescale/p1_p2_rdb/pci.c | 27 -
board/freescale/p1_p2_rdb/spl.c | 141 ------
board/freescale/p1_p2_rdb/spl_minimal.c | 84 ----
board/freescale/p1_p2_rdb/tlb.c | 91 ----
configs/P1011RDB_36BIT_SDCARD_defconfig | 5 -
configs/P1011RDB_36BIT_SPIFLASH_defconfig | 5 -
configs/P1011RDB_36BIT_defconfig | 4 -
configs/P1011RDB_NAND_defconfig | 6 -
configs/P1011RDB_SDCARD_defconfig | 5 -
configs/P1011RDB_SPIFLASH_defconfig | 5 -
configs/P1011RDB_defconfig | 4 -
configs/P1020RDB_36BIT_SDCARD_defconfig | 5 -
configs/P1020RDB_36BIT_SPIFLASH_defconfig | 5 -
configs/P1020RDB_36BIT_defconfig | 4 -
configs/P1020RDB_NAND_defconfig | 6 -
configs/P1020RDB_SDCARD_defconfig | 5 -
configs/P1020RDB_SPIFLASH_defconfig | 5 -
configs/P1020RDB_defconfig | 4 -
configs/P2010RDB_36BIT_SDCARD_defconfig | 5 -
configs/P2010RDB_36BIT_SPIFLASH_defconfig | 5 -
configs/P2010RDB_36BIT_defconfig | 4 -
configs/P2010RDB_NAND_defconfig | 6 -
configs/P2010RDB_SDCARD_defconfig | 5 -
configs/P2010RDB_SPIFLASH_defconfig | 5 -
configs/P2010RDB_defconfig | 4 -
configs/P2020RDB_36BIT_SDCARD_defconfig | 5 -
configs/P2020RDB_36BIT_SPIFLASH_defconfig | 5 -
configs/P2020RDB_36BIT_defconfig | 4 -
configs/P2020RDB_NAND_defconfig | 6 -
configs/P2020RDB_SDCARD_defconfig | 5 -
configs/P2020RDB_SPIFLASH_defconfig | 5 -
configs/P2020RDB_defconfig | 4 -
doc/README.scrapyard | 4 +
include/configs/P1_P2_RDB.h | 808 ------------------------------
42 files changed, 4 insertions(+), 2058 deletions(-)
delete mode 100644 board/freescale/p1_p2_rdb/Kconfig
delete mode 100644 board/freescale/p1_p2_rdb/MAINTAINERS
delete mode 100644 board/freescale/p1_p2_rdb/Makefile
delete mode 100644 board/freescale/p1_p2_rdb/README
delete mode 100644 board/freescale/p1_p2_rdb/ddr.c
delete mode 100644 board/freescale/p1_p2_rdb/law.c
delete mode 100644 board/freescale/p1_p2_rdb/p1_p2_rdb.c
delete mode 100644 board/freescale/p1_p2_rdb/pci.c
delete mode 100644 board/freescale/p1_p2_rdb/spl.c
delete mode 100644 board/freescale/p1_p2_rdb/spl_minimal.c
delete mode 100644 board/freescale/p1_p2_rdb/tlb.c
delete mode 100644 configs/P1011RDB_36BIT_SDCARD_defconfig
delete mode 100644 configs/P1011RDB_36BIT_SPIFLASH_defconfig
delete mode 100644 configs/P1011RDB_36BIT_defconfig
delete mode 100644 configs/P1011RDB_NAND_defconfig
delete mode 100644 configs/P1011RDB_SDCARD_defconfig
delete mode 100644 configs/P1011RDB_SPIFLASH_defconfig
delete mode 100644 configs/P1011RDB_defconfig
delete mode 100644 configs/P1020RDB_36BIT_SDCARD_defconfig
delete mode 100644 configs/P1020RDB_36BIT_SPIFLASH_defconfig
delete mode 100644 configs/P1020RDB_36BIT_defconfig
delete mode 100644 configs/P1020RDB_NAND_defconfig
delete mode 100644 configs/P1020RDB_SDCARD_defconfig
delete mode 100644 configs/P1020RDB_SPIFLASH_defconfig
delete mode 100644 configs/P1020RDB_defconfig
delete mode 100644 configs/P2010RDB_36BIT_SDCARD_defconfig
delete mode 100644 configs/P2010RDB_36BIT_SPIFLASH_defconfig
delete mode 100644 configs/P2010RDB_36BIT_defconfig
delete mode 100644 configs/P2010RDB_NAND_defconfig
delete mode 100644 configs/P2010RDB_SDCARD_defconfig
delete mode 100644 configs/P2010RDB_SPIFLASH_defconfig
delete mode 100644 configs/P2010RDB_defconfig
delete mode 100644 configs/P2020RDB_36BIT_SDCARD_defconfig
delete mode 100644 configs/P2020RDB_36BIT_SPIFLASH_defconfig
delete mode 100644 configs/P2020RDB_36BIT_defconfig
delete mode 100644 configs/P2020RDB_NAND_defconfig
delete mode 100644 configs/P2020RDB_SDCARD_defconfig
delete mode 100644 configs/P2020RDB_SPIFLASH_defconfig
delete mode 100644 configs/P2020RDB_defconfig
delete mode 100644 include/configs/P1_P2_RDB.h
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 7501eb4..009d830 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -85,11 +85,6 @@ config TARGET_P1022DS
config TARGET_P1023RDB
bool "Support P1023RDB"
-config TARGET_P1_P2_RDB
- bool "Support P1_P2_RDB"
- select SUPPORT_SPL
- select SUPPORT_TPL
-
config TARGET_P1_P2_RDB_PC
bool "Support p1_p2_rdb_pc"
select SUPPORT_SPL
@@ -184,7 +179,6 @@ source "board/freescale/mpc8572ds/Kconfig"
source "board/freescale/p1010rdb/Kconfig"
source "board/freescale/p1022ds/Kconfig"
source "board/freescale/p1023rdb/Kconfig"
-source "board/freescale/p1_p2_rdb/Kconfig"
source "board/freescale/p1_p2_rdb_pc/Kconfig"
source "board/freescale/p1_twr/Kconfig"
source "board/freescale/p2020come/Kconfig"
diff --git a/board/freescale/p1_p2_rdb/Kconfig b/board/freescale/p1_p2_rdb/Kconfig
deleted file mode 100644
index d7ad35d..0000000
--- a/board/freescale/p1_p2_rdb/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_P1_P2_RDB
-
-config SYS_BOARD
- default "p1_p2_rdb"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "P1_P2_RDB"
-
-endif
diff --git a/board/freescale/p1_p2_rdb/MAINTAINERS b/board/freescale/p1_p2_rdb/MAINTAINERS
deleted file mode 100644
index aabf587..0000000
--- a/board/freescale/p1_p2_rdb/MAINTAINERS
+++ /dev/null
@@ -1,37 +0,0 @@
-P1_P2_RDB BOARD
-#M: -
-S: Maintained
-F: board/freescale/p1_p2_rdb/
-F: include/configs/P1_P2_RDB.h
-F: configs/P1011RDB_defconfig
-F: configs/P1011RDB_36BIT_defconfig
-F: configs/P1011RDB_36BIT_SDCARD_defconfig
-F: configs/P1011RDB_36BIT_SPIFLASH_defconfig
-F: configs/P1011RDB_NAND_defconfig
-F: configs/P1011RDB_SDCARD_defconfig
-F: configs/P1011RDB_SPIFLASH_defconfig
-F: configs/P1020RDB_defconfig
-F: configs/P1020RDB_36BIT_defconfig
-F: configs/P1020RDB_36BIT_SDCARD_defconfig
-F: configs/P1020RDB_36BIT_SPIFLASH_defconfig
-F: configs/P1020RDB_NAND_defconfig
-F: configs/P1020RDB_SDCARD_defconfig
-F: configs/P1020RDB_SPIFLASH_defconfig
-F: configs/P2010RDB_defconfig
-F: configs/P2010RDB_36BIT_defconfig
-F: configs/P2010RDB_36BIT_SDCARD_defconfig
-F: configs/P2010RDB_36BIT_SPIFLASH_defconfig
-F: configs/P2010RDB_NAND_defconfig
-F: configs/P2010RDB_SDCARD_defconfig
-F: configs/P2010RDB_SPIFLASH_defconfig
-F: configs/P2020RDB_36BIT_defconfig
-F: configs/P2020RDB_36BIT_SDCARD_defconfig
-F: configs/P2020RDB_36BIT_SPIFLASH_defconfig
-F: configs/P2020RDB_NAND_defconfig
-F: configs/P2020RDB_SDCARD_defconfig
-F: configs/P2020RDB_SPIFLASH_defconfig
-
-P2020RDB BOARD
-M: Poonam Aggrwal <poonam.aggrwal at freescale.com>
-S: Maintained
-F: configs/P2020RDB_defconfig
diff --git a/board/freescale/p1_p2_rdb/Makefile b/board/freescale/p1_p2_rdb/Makefile
deleted file mode 100644
index a97bf45..0000000
--- a/board/freescale/p1_p2_rdb/Makefile
+++ /dev/null
@@ -1,30 +0,0 @@
-#
-# Copyright 2009 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-MINIMAL=
-
-ifdef CONFIG_SPL_BUILD
-ifdef CONFIG_SPL_INIT_MINIMAL
-MINIMAL=y
-endif
-endif
-
-ifdef MINIMAL
-
-obj-y += spl_minimal.o tlb.o law.o
-
-else
-ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
-else
-obj-y += p1_p2_rdb.o
-obj-$(CONFIG_PCI) += pci.o
-endif
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
-
-endif
diff --git a/board/freescale/p1_p2_rdb/README b/board/freescale/p1_p2_rdb/README
deleted file mode 100644
index cd66e58..0000000
--- a/board/freescale/p1_p2_rdb/README
+++ /dev/null
@@ -1,145 +0,0 @@
-Overview
---------
-P2020RDB is a Low End Dual core platform supporting the P2020 processor
-of QorIQ series. P2020 is an e500 based dual core SOC.
-
-Building U-boot
------------
-To build the u-boot for P2020RDB:
- make P2020RDB_config
- make
-
-NOR Flash Banks
------------
-RDB board for P2020 has two flash banks. They are both present on boot.
-
-Booting by default is always from the boot bank at 0xef00_0000.
-
-Memory Map
-----------
-0xef00_0000 - 0xef7f_ffff Alternate bank 8MB
-0xe800_0000 - 0xefff_ffff Boot bank 8MB
-
-0xef74_0000 - 0xef7f_ffff Alternate u-boot address 768KB
-0xeff4_0000 - 0xefff_ffff Boot u-boot address 768KB
-
-Switch settings to boot from the NOR flash banks
-------------------------------------------------
-SW4[8]=0 default NOR Flash bank
-SW4[8]=1 Alternate NOR Flash bank
-
-Flashing Images
----------------
-To place a new u-boot image in the alternate flash bank and then boot
-with that new image temporarily, use this:
- tftp 1000000 u-boot.bin
- erase ef740000 ef7fffff
- cp.b 1000000 ef740000 c0000
-
-Now to boot from the alternate bank change the SW4[8] from 0 to 1.
-
-To program the image in the boot flash bank:
- tftp 1000000 u-boot.bin
- protect off all
- erase eff40000 ffffffff
- cp.b 1000000 eff40000 c0000
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
- dtc -b 0 -f -I dts -O dtb p2020rdb.dts > p2020rdb.dtb
-
-Likely, that .dts file will come from here;
-
- linux-2.6/arch/powerpc/boot/dts/p2020rdb.dts
-
-Booting Linux
--------------
-Place a linux uImage in the TFTP disk area.
-
- tftp 1000000 uImage.p2020rdb
- tftp 2000000 rootfs.ext2.gz.uboot
- tftp c00000 p2020rdb.dtb
- bootm 1000000 2000000 c00000
-
-Implementing AMP(Asymmetric MultiProcessing)
----------------------------------------------
-1. Build kernel image for core0:
-
- a. $ make 85xx/p1_p2_rdb_defconfig
-
- b. $ make menuconfig
- - un-select "Processor support"->
- "Symetric multi-processing support"
-
- c. $ make uImage
-
- d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
-
-2. Build kernel image for core1:
-
- a. $ make 85xx/p1_p2_rdb_defconfig
-
- b. $ make menuconfig
- - Un-select "Processor support"->
- "Symetric multi-processing support"
- - Select "Advanced setup" ->
- "Prompt for advanced kernel configuration options"
- - Select
- "Set physical address where the kernel is loaded"
- and set it to 0x20000000, assuming core1 will
- start from 512MB.
- - Select "Set custom page offset address"
- - Select "Set custom kernel base address"
- - Select "Set maximum low memory"
- - "Exit" and save the selection.
-
- c. $ make uImage
-
- d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
-
-3. Create dtb for core0:
-
- $ dtc -I dts -O dtb -f -b 0
- arch/powerpc/boot/dts/p2020rdb_camp_core0.dts >
- /tftpboot/p2020rdb_camp_core0.dtb
-
-4. Create dtb for core1:
-
- $ dtc -I dts -O dtb -f -b 1
- arch/powerpc/boot/dts/p2020rdb_camp_core1.dts >
- /tftpboot/p2020rdb_camp_core1.dtb
-
-5. Bring up two cores separately:
-
- a. Power on the board, under u-boot prompt:
- => setenv <serverip>
- => setenv <ipaddr>
- => setenv bootargs root=/dev/ram rw console=ttyS0,115200
- b. Bring up core1's kernel first:
- => setenv bootm_low 0x20000000
- => setenv bootm_size 0x10000000
- => tftp 21000000 uImage.core1
- => tftp 22000000 ramdiskfile
- => tftp 20c00000 p2020rdb_camp_core1.dtb
- => interrupts off
- => bootm start 21000000 22000000 20c00000
- => bootm loados
- => bootm ramdisk
- => bootm fdt
- => fdt boardsetup
- => fdt chosen $initrd_start $initrd_end
- => bootm prep
- => cpu 1 release $bootm_low - $fdtaddr -
- c. Bring up core0's kernel(on the same u-boot console):
- => setenv bootm_low 0
- => setenv bootm_size 0x20000000
- => tftp 1000000 uImage.core0
- => tftp 2000000 ramdiskfile
- => tftp c00000 p2020rdb_camp_core0.dtb
- => bootm 1000000 2000000 c00000
-
-Please note only core0 will run u-boot, core1 starts kernel directly
-after "cpu release" command is issued.
diff --git a/board/freescale/p1_p2_rdb/ddr.c b/board/freescale/p1_p2_rdb/ddr.c
deleted file mode 100644
index 98ee5f1..0000000
--- a/board/freescale/p1_p2_rdb/ddr.c
+++ /dev/null
@@ -1,221 +0,0 @@
-/*
- * Copyright 2009, 2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/processor.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/io.h>
-#include <asm/fsl_law.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
-#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-#define CONFIG_SYS_DDR_ZQ_CONTROL 0x00000000
-#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x00000000
-#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
-#define CONFIG_SYS_DDR_RCW_1 0x00000000
-#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0x43000000 /* Type = DDR2*/
-#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
-#define CONFIG_SYS_DDR_TIMING_4 0x00000000
-#define CONFIG_SYS_DDR_TIMING_5 0x00000000
-
-#define CONFIG_SYS_DDR_TIMING_3_400 0x00010000
-#define CONFIG_SYS_DDR_TIMING_0_400 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1_400 0x39355322
-#define CONFIG_SYS_DDR_TIMING_2_400 0x1f9048ca
-#define CONFIG_SYS_DDR_CLK_CTRL_400 0x02800000
-#define CONFIG_SYS_DDR_MODE_1_400 0x00480432
-#define CONFIG_SYS_DDR_MODE_2_400 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_400 0x06180100
-
-#define CONFIG_SYS_DDR_TIMING_3_533 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0_533 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1_533 0x4c47c432
-#define CONFIG_SYS_DDR_TIMING_2_533 0x0f9848ce
-#define CONFIG_SYS_DDR_CLK_CTRL_533 0x02800000
-#define CONFIG_SYS_DDR_MODE_1_533 0x00040642
-#define CONFIG_SYS_DDR_MODE_2_533 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_533 0x08200100
-
-#define CONFIG_SYS_DDR_TIMING_3_667 0x00030000
-#define CONFIG_SYS_DDR_TIMING_0_667 0x55770802
-#define CONFIG_SYS_DDR_TIMING_1_667 0x5f599543
-#define CONFIG_SYS_DDR_TIMING_2_667 0x0fa074d1
-#define CONFIG_SYS_DDR_CLK_CTRL_667 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_667 0x00040852
-#define CONFIG_SYS_DDR_MODE_2_667 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_667 0x0a280100
-
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00040000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00770802
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b6543
-#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa074d1
-#define CONFIG_SYS_DDR_CLK_CTRL_800 0x02800000
-#define CONFIG_SYS_DDR_MODE_1_800 0x00040852
-#define CONFIG_SYS_DDR_MODE_2_800 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100
-
-fsl_ddr_cfg_regs_t ddr_cfg_regs_400 = {
- .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
- .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
- .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
- .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_400,
- .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_400,
- .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_400,
- .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_400,
- .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
- .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
- .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_400,
- .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_400,
- .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
- .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_400,
- .ddr_data_init = CONFIG_MEM_INIT_VALUE,
- .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_400,
- .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
- .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
- .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
- .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
- .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
- .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
- .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
- .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
- .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
-};
-
-fsl_ddr_cfg_regs_t ddr_cfg_regs_533 = {
- .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
- .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
- .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
- .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_533,
- .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_533,
- .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_533,
- .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_533,
- .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
- .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
- .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_533,
- .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_533,
- .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
- .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_533,
- .ddr_data_init = CONFIG_MEM_INIT_VALUE,
- .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_533,
- .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
- .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
- .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
- .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
- .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
- .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
- .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
- .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
- .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
-};
-
-fsl_ddr_cfg_regs_t ddr_cfg_regs_667 = {
- .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
- .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
- .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
- .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_667,
- .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_667,
- .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_667,
- .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_667,
- .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
- .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
- .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_667,
- .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_667,
- .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
- .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_667,
- .ddr_data_init = CONFIG_MEM_INIT_VALUE,
- .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_667,
- .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
- .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
- .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
- .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
- .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
- .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
- .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
- .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
- .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
-};
-
-fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
- .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
- .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
- .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
- .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
- .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
- .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
- .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
- .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
- .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
- .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
- .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
- .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
- .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
- .ddr_data_init = CONFIG_MEM_INIT_VALUE,
- .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
- .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
- .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
- .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
- .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
- .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
- .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
- .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
- .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
- .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
-};
-
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-
-phys_size_t fixed_sdram (void)
-{
- fsl_ddr_cfg_regs_t ddr_cfg_regs;
- size_t ddr_size;
- struct cpu_type *cpu;
- ulong ddr_freq, ddr_freq_mhz;
-
- cpu = gd->arch.cpu;
-
- ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-
-#if defined(CONFIG_SYS_RAMBOOT)
- return ddr_size;
-#endif
- ddr_freq = get_ddr_freq(0);
- ddr_freq_mhz = ddr_freq / 1000000;
-
- printf("Configuring DDR for %ld T/s data rate\n", ddr_freq);
-
- if(ddr_freq_mhz <= 400)
- memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs));
- else if(ddr_freq_mhz <= 533)
- memcpy(&ddr_cfg_regs, &ddr_cfg_regs_533, sizeof(ddr_cfg_regs));
- else if(ddr_freq_mhz <= 667)
- memcpy(&ddr_cfg_regs, &ddr_cfg_regs_667, sizeof(ddr_cfg_regs));
- else if(ddr_freq_mhz <= 800)
- memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs));
- else
- panic("Unsupported DDR data rate %ld T/s\n", ddr_freq);
-
- /* P1020 and it's derivatives support max 32bit DDR width */
- if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
- ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_32_BE;
- ddr_cfg_regs.cs[0].bnds = 0x0000001F;
- }
-
- fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
-
- set_ddr_laws(0, ddr_size, LAW_TRGT_IF_DDR_1);
- return ddr_size;
-}
diff --git a/board/freescale/p1_p2_rdb/law.c b/board/freescale/p1_p2_rdb/law.c
deleted file mode 100644
index b60a27f..0000000
--- a/board/freescale/p1_p2_rdb/law.c
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c
deleted file mode 100644
index 61ed466..0000000
--- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c
+++ /dev/null
@@ -1,303 +0,0 @@
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <vsc7385.h>
-#include <netdev.h>
-#include <rtc.h>
-#include <i2c.h>
-#include <hwconfig.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define VSC7385_RST_SET 0x00080000
-#define SLIC_RST_SET 0x00040000
-#define SGMII_PHY_RST_SET 0x00020000
-#define PCIE_RST_SET 0x00010000
-#define RGMII_PHY_RST_SET 0x02000000
-
-#define USB_RST_CLR 0x04000000
-#define USB2_PORT_OUT_EN 0x01000000
-
-#define GPIO_DIR 0x060f0000
-
-#define BOARD_PERI_RST_SET VSC7385_RST_SET | SLIC_RST_SET | \
- SGMII_PHY_RST_SET | PCIE_RST_SET | \
- RGMII_PHY_RST_SET
-
-#define SYSCLK_MASK 0x00200000
-#define BOARDREV_MASK 0x10100000
-#define BOARDREV_C 0x00100000
-#define BOARDREV_D 0x00000000
-
-#define SYSCLK_66 66666666
-#define SYSCLK_100 100000000
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
- volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val_gpdat, sysclk_gpio;
-
- val_gpdat = in_be32(&pgpio->gpdat);
- sysclk_gpio = val_gpdat & SYSCLK_MASK;
-
- if(sysclk_gpio == 0)
- return SYSCLK_66;
- else
- return SYSCLK_100;
-
- return 0;
-}
-
-#ifdef CONFIG_MMC
-int board_early_init_f (void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-
- setbits_be32(&gur->pmuxcr,
- (MPC85xx_PMUXCR_SDHC_CD |
- MPC85xx_PMUXCR_SDHC_WP));
- return 0;
-}
-#endif
-
-int checkboard (void)
-{
- u32 val_gpdat, board_rev_gpio;
- volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- char board_rev = 0;
- struct cpu_type *cpu;
-
- val_gpdat = in_be32(&pgpio->gpdat);
- board_rev_gpio = val_gpdat & BOARDREV_MASK;
- if (board_rev_gpio == BOARDREV_C)
- board_rev = 'C';
- else if (board_rev_gpio == BOARDREV_D)
- board_rev = 'D';
- else
- panic ("Unexpected Board REV %x detected!!\n", board_rev_gpio);
-
- cpu = gd->arch.cpu;
- printf ("Board: %sRDB Rev%c\n", cpu->name, board_rev);
-
- setbits_be32(&pgpio->gpdir, GPIO_DIR);
-
-/*
- * Bringing the following peripherals out of reset via GPIOs
- * 0 = reset and 1 = out of reset
- * GPIO12 - Reset to Ethernet Switch
- * GPIO13 - Reset to SLIC/SLAC devices
- * GPIO14 - Reset to SGMII_PHY_N
- * GPIO15 - Reset to PCIe slots
- * GPIO6 - Reset to RGMII PHY
- * GPIO5 - Reset to USB3300 devices 1 = reset and 0 = out of reset
- */
- clrsetbits_be32(&pgpio->gpdat, USB_RST_CLR, BOARD_PERI_RST_SET);
-
- return 0;
-}
-
-int misc_init_r(void)
-{
-#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
- ccsr_gpio_t *gpio = (void *)CONFIG_SYS_MPC85xx_GPIO_ADDR;
-
- setbits_be32(&gpio->gpdir, USB2_PORT_OUT_EN);
- setbits_be32(&gpio->gpdat, USB2_PORT_OUT_EN);
- setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_ELBC_OFF_USB2_ON);
-#endif
- return 0;
-}
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- int flash_esel = find_tlb_idx((void *)flashbase, 1);
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- unsigned int orig_bus = i2c_get_bus_num();
- u8 i2c_data;
-
- i2c_set_bus_num(1);
- if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0,
- 1, &i2c_data, sizeof(i2c_data)) == 0) {
- if (i2c_data & 0x2)
- puts("NOR Flash Bank : Secondary\n");
- else
- puts("NOR Flash Bank : Primary\n");
-
- if (i2c_data & 0x1) {
- setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
- puts("SD/MMC : 8-bit Mode\n");
- puts("eSPI : Disabled\n");
- } else {
- puts("SD/MMC : 4-bit Mode\n");
- puts("eSPI : Enabled\n");
- }
- } else {
- puts("Failed reading I2C Chip 0x18 on bus 1\n");
- }
- i2c_set_bus_num(orig_bus);
-
- /*
- * Remap Boot flash region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- if (flash_esel == -1) {
- /* very unlikely unless something is messed up */
- puts("Error: Could not find TLB for FLASH BASE\n");
- flash_esel = 2; /* give our best effort to continue */
- } else {
- /* invalidate existing TLB entry for flash */
- disable_tlb(flash_esel);
- }
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_16M, 1);
- rtc_reset();
- return 0;
-}
-
-
-#ifdef CONFIG_TSEC_ENET
-int board_eth_init(bd_t *bis)
-{
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- int num = 0;
- char *tmp;
- unsigned int vscfw_addr;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- if (is_serdes_configured(SGMII_TSEC3)) {
- puts("eTSEC3 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
- if (!num) {
- printf("No TSECs initialized\n");
- return 0;
- }
-#ifdef CONFIG_VSC7385_ENET
-/* If a VSC7385 microcode image is present, then upload it. */
- if ((tmp = getenv ("vscfw_addr")) != NULL) {
- vscfw_addr = simple_strtoul (tmp, NULL, 16);
- printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
- if (vsc7385_upload_firmware((void *) vscfw_addr,
- CONFIG_VSC7385_IMAGE_SIZE))
- puts("Failure uploading VSC7385 microcode.\n");
- } else
- puts("No address specified for VSC7385 microcode.\n");
-#endif
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-
- return pci_eth_init(bis);
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-extern void ft_pci_board_setup(void *blob);
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- const char *soc_usb_compat = "fsl-usb2-dr";
- int err, usb1_off, usb2_off;
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = getenv_bootm_low();
- size = getenv_bootm_size();
-
-#if defined(CONFIG_PCI)
- ft_pci_board_setup(blob);
-#endif /* #if defined(CONFIG_PCI) */
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
- fdt_fixup_dr_usb(blob, bd);
-#endif
-
-#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
- /* Delete eLBC node as it is muxed with USB2 controller */
- if (hwconfig("usb2")) {
- const char *soc_elbc_compat = "fsl,p1020-elbc";
- int off = fdt_node_offset_by_compatible(blob, -1,
- soc_elbc_compat);
- if (off < 0) {
- printf("WARNING: could not find compatible node %s\n",
- soc_elbc_compat);
- return off;
- }
- err = fdt_del_node(blob, off);
- if (err < 0) {
- printf("WARNING: could not remove %s\n",
- soc_elbc_compat);
- return err;
- }
- return 0;
- }
-#endif
- /* Delete USB2 node as it is muxed with eLBC */
- usb1_off = fdt_node_offset_by_compatible(blob, -1,
- soc_usb_compat);
- if (usb1_off < 0) {
- printf("WARNING: could not find compatible node %s\n",
- soc_usb_compat);
- return usb1_off;
- }
- usb2_off = fdt_node_offset_by_compatible(blob, usb1_off,
- soc_usb_compat);
- if (usb2_off < 0) {
- printf("WARNING: could not find compatible node %s\n",
- soc_usb_compat);
- return usb2_off;
- }
- err = fdt_del_node(blob, usb2_off);
- if (err < 0) {
- printf("WARNING: could not remove %s\n", soc_usb_compat);
- return err;
- }
-
- return 0;
-}
-
-#endif
diff --git a/board/freescale/p1_p2_rdb/pci.c b/board/freescale/p1_p2_rdb/pci.c
deleted file mode 100644
index 745ebb1..0000000
--- a/board/freescale/p1_p2_rdb/pci.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <pci.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <asm/fsl_pci.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-
-void ft_pci_board_setup(void *blob)
-{
- FT_FSL_PCI_SETUP;
-}
diff --git a/board/freescale/p1_p2_rdb/spl.c b/board/freescale/p1_p2_rdb/spl.c
deleted file mode 100644
index f30c5fe..0000000
--- a/board/freescale/p1_p2_rdb/spl.c
+++ /dev/null
@@ -1,141 +0,0 @@
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ns16550.h>
-#include <malloc.h>
-#include <mmc.h>
-#include <nand.h>
-#include <i2c.h>
-#include <fsl_esdhc.h>
-#include <spi_flash.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define SYSCLK_MASK 0x00200000
-#define BOARDREV_MASK 0x10100000
-
-#define SYSCLK_66 66666666
-#define SYSCLK_100 100000000
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
- ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val_gpdat, sysclk_gpio;
-
- val_gpdat = in_be32(&pgpio->gpdat);
- sysclk_gpio = val_gpdat & SYSCLK_MASK;
-
- if (sysclk_gpio == 0)
- return SYSCLK_66;
- else
- return SYSCLK_100;
-
- return 0;
-}
-
-phys_size_t get_effective_memsize(void)
-{
- return CONFIG_SYS_L2_SIZE;
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio, bus_clk;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- console_init_f();
-
- /* Set pmuxcr to allow both i2c1 and i2c2 */
- setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
- setbits_be32(&gur->pmuxcr,
- in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
-
- /* Read back the register to synchronize the write. */
- in_be32(&gur->pmuxcr);
-
-#ifdef CONFIG_SPL_SPI_BOOT
- clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
-#endif
-
- /* initialize selected port with appropriate baud rate */
- plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
- plat_ratio >>= 1;
- bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
- gd->bus_clk = bus_clk;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- bus_clk / 16 / CONFIG_BAUDRATE);
-#ifdef CONFIG_SPL_MMC_BOOT
- puts("\nSD boot...\n");
-#elif defined(CONFIG_SPL_SPI_BOOT)
- puts("\nSPI Flash boot...\n");
-#endif
-
- /* copy code to RAM and jump to it - this should not return */
- /* NOTE - code has to be copied out of NAND buffer before
- * other blocks can be read.
- */
- relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- /* Pointer is writable since we allocated a register for it */
- gd = (gd_t *)CONFIG_SPL_GD_ADDR;
- bd_t *bd;
-
- memset(gd, 0, sizeof(gd_t));
- bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
- memset(bd, 0, sizeof(bd_t));
- gd->bd = bd;
- bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
- bd->bi_memsize = CONFIG_SYS_L2_SIZE;
-
- probecpu();
- get_clocks();
- mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
- CONFIG_SPL_RELOC_MALLOC_SIZE);
-
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_initialize(bd);
-#endif
- /* relocate environment function pointers etc. */
-#ifdef CONFIG_SPL_NAND_BOOT
- nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_NAND_BOOT
- nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_SPI_BOOT
- spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)CONFIG_ENV_ADDR);
-#endif
-
- gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
- gd->env_valid = 1;
-
- gd->ram_size = initdram(0);
-#ifdef CONFIG_SPL_NAND_BOOT
- puts("Tertiary program loader running in sram...");
-#else
- puts("Second program loader running in sram...\n");
-#endif
-
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_boot();
-#elif defined(CONFIG_SPL_SPI_BOOT)
- spi_boot();
-#elif defined(CONFIG_SPL_NAND_BOOT)
- nand_boot();
-#endif
-}
diff --git a/board/freescale/p1_p2_rdb/spl_minimal.c b/board/freescale/p1_p2_rdb/spl_minimal.c
deleted file mode 100644
index 96a4d1c..0000000
--- a/board/freescale/p1_p2_rdb/spl_minimal.c
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ns16550.h>
-#include <asm/io.h>
-#include <nand.h>
-#include <linux/compiler.h>
-#include <asm/fsl_law.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/global_data.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-#define SYSCLK_MASK 0x00200000
-#define BOARDREV_MASK 0x10100000
-
-#define SYSCLK_66 66666666
-#define SYSCLK_100 100000000
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
- ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val_gpdat, sysclk_gpio;
-
- val_gpdat = in_be32(&pgpio->gpdat);
- sysclk_gpio = val_gpdat & SYSCLK_MASK;
-
- if (sysclk_gpio == 0)
- return SYSCLK_66;
- else
- return SYSCLK_100;
-
- return 0;
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
-#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
- set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
- set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
-#endif
-
- /* initialize selected port with appropriate baud rate */
- plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
- plat_ratio >>= 1;
- gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- gd->bus_clk / 16 / CONFIG_BAUDRATE);
-
- puts("\nNAND boot... ");
-
- /* copy code to RAM and jump to it - this should not return */
- /* NOTE - code has to be copied out of NAND buffer before
- * other blocks can be read.
- */
- relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- puts("\nSecond program loader running in sram...");
- nand_boot();
-}
-
-void putc(char c)
-{
- if (c == '\n')
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
-
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
-}
-
-void puts(const char *str)
-{
- while (*str)
- putc(*str++);
-}
diff --git a/board/freescale/p1_p2_rdb/tlb.c b/board/freescale/p1_p2_rdb/tlb.c
deleted file mode 100644
index 73f5729..0000000
--- a/board/freescale/p1_p2_rdb/tlb.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
-#ifndef CONFIG_SPL_BUILD
- /* W**G* - Flash/promjet, localbus */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_16M, 1),
-
-#if defined(CONFIG_PCI)
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256K, 1),
-
-#endif /* #if defined(CONFIG_PCI) */
-#endif
- /* *I*G - NAND */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_1M, 1),
-
- /* *I*G - VSC7385 Switch */
- SET_TLB_ENTRY(1, CONFIG_SYS_VSC7385_BASE, CONFIG_SYS_VSC7385_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_1M, 1),
-
-#ifdef CONFIG_SYS_INIT_L2_ADDR
- /* *I*G - L2SRAM */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
- 0, 11, BOOKE_PAGESZ_256K, 1),
-#if CONFIG_SYS_L2_SIZE >= (256 << 10)
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
- CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 12, BOOKE_PAGESZ_256K, 1),
-#endif
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT) || \
- (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 7, BOOKE_PAGESZ_1G, 1)
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/P1011RDB_36BIT_SDCARD_defconfig b/configs/P1011RDB_36BIT_SDCARD_defconfig
deleted file mode 100644
index 7205bef..0000000
--- a/configs/P1011RDB_36BIT_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,36BIT,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_36BIT_SPIFLASH_defconfig b/configs/P1011RDB_36BIT_SPIFLASH_defconfig
deleted file mode 100644
index 8b3806e..0000000
--- a/configs/P1011RDB_36BIT_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,36BIT,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_36BIT_defconfig b/configs/P1011RDB_36BIT_defconfig
deleted file mode 100644
index c47f2e2..0000000
--- a/configs/P1011RDB_36BIT_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,36BIT"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_NAND_defconfig b/configs/P1011RDB_NAND_defconfig
deleted file mode 100644
index aac0190..0000000
--- a/configs/P1011RDB_NAND_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_SPL=y
-CONFIG_TPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,NAND"
-+ST:CONFIG_PPC=y
-+ST:CONFIG_MPC85xx=y
-+ST:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_SDCARD_defconfig b/configs/P1011RDB_SDCARD_defconfig
deleted file mode 100644
index 16e872f..0000000
--- a/configs/P1011RDB_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_SPIFLASH_defconfig b/configs/P1011RDB_SPIFLASH_defconfig
deleted file mode 100644
index d14820f..0000000
--- a/configs/P1011RDB_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1011RDB_defconfig b/configs/P1011RDB_defconfig
deleted file mode 100644
index d14868a..0000000
--- a/configs/P1011RDB_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P1011RDB"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_36BIT_SDCARD_defconfig b/configs/P1020RDB_36BIT_SDCARD_defconfig
deleted file mode 100644
index a18563e..0000000
--- a/configs/P1020RDB_36BIT_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,36BIT,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_36BIT_SPIFLASH_defconfig b/configs/P1020RDB_36BIT_SPIFLASH_defconfig
deleted file mode 100644
index aa145fc..0000000
--- a/configs/P1020RDB_36BIT_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,36BIT,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_36BIT_defconfig b/configs/P1020RDB_36BIT_defconfig
deleted file mode 100644
index 844651f..0000000
--- a/configs/P1020RDB_36BIT_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,36BIT"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_NAND_defconfig b/configs/P1020RDB_NAND_defconfig
deleted file mode 100644
index 441241b..0000000
--- a/configs/P1020RDB_NAND_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_SPL=y
-CONFIG_TPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,NAND"
-+ST:CONFIG_PPC=y
-+ST:CONFIG_MPC85xx=y
-+ST:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_SDCARD_defconfig b/configs/P1020RDB_SDCARD_defconfig
deleted file mode 100644
index 1349bea..0000000
--- a/configs/P1020RDB_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_SPIFLASH_defconfig b/configs/P1020RDB_SPIFLASH_defconfig
deleted file mode 100644
index 7eb8696..0000000
--- a/configs/P1020RDB_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P1020RDB_defconfig b/configs/P1020RDB_defconfig
deleted file mode 100644
index fc58ac9..0000000
--- a/configs/P1020RDB_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P1020RDB"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_36BIT_SDCARD_defconfig b/configs/P2010RDB_36BIT_SDCARD_defconfig
deleted file mode 100644
index 1381e8e..0000000
--- a/configs/P2010RDB_36BIT_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,36BIT,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_36BIT_SPIFLASH_defconfig b/configs/P2010RDB_36BIT_SPIFLASH_defconfig
deleted file mode 100644
index 53ebca1..0000000
--- a/configs/P2010RDB_36BIT_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,36BIT,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_36BIT_defconfig b/configs/P2010RDB_36BIT_defconfig
deleted file mode 100644
index de29dcb..0000000
--- a/configs/P2010RDB_36BIT_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,36BIT"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_NAND_defconfig b/configs/P2010RDB_NAND_defconfig
deleted file mode 100644
index bc91a67..0000000
--- a/configs/P2010RDB_NAND_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_SPL=y
-CONFIG_TPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,NAND"
-+ST:CONFIG_PPC=y
-+ST:CONFIG_MPC85xx=y
-+ST:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_SDCARD_defconfig b/configs/P2010RDB_SDCARD_defconfig
deleted file mode 100644
index fd4ade7..0000000
--- a/configs/P2010RDB_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_SPIFLASH_defconfig b/configs/P2010RDB_SPIFLASH_defconfig
deleted file mode 100644
index 9631864..0000000
--- a/configs/P2010RDB_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2010RDB_defconfig b/configs/P2010RDB_defconfig
deleted file mode 100644
index 3b3352a..0000000
--- a/configs/P2010RDB_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P2010RDB"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_36BIT_SDCARD_defconfig b/configs/P2020RDB_36BIT_SDCARD_defconfig
deleted file mode 100644
index 43cc2e3..0000000
--- a/configs/P2020RDB_36BIT_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,36BIT,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_36BIT_SPIFLASH_defconfig b/configs/P2020RDB_36BIT_SPIFLASH_defconfig
deleted file mode 100644
index f1199b6..0000000
--- a/configs/P2020RDB_36BIT_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,36BIT,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_36BIT_defconfig b/configs/P2020RDB_36BIT_defconfig
deleted file mode 100644
index 87490fd..0000000
--- a/configs/P2020RDB_36BIT_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,36BIT"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_NAND_defconfig b/configs/P2020RDB_NAND_defconfig
deleted file mode 100644
index 70ee084..0000000
--- a/configs/P2020RDB_NAND_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_SPL=y
-CONFIG_TPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,NAND"
-+ST:CONFIG_PPC=y
-+ST:CONFIG_MPC85xx=y
-+ST:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_SDCARD_defconfig b/configs/P2020RDB_SDCARD_defconfig
deleted file mode 100644
index 2bf5773..0000000
--- a/configs/P2020RDB_SDCARD_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,SDCARD"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_SPIFLASH_defconfig b/configs/P2020RDB_SPIFLASH_defconfig
deleted file mode 100644
index 290ebd2..0000000
--- a/configs/P2020RDB_SPIFLASH_defconfig
+++ /dev/null
@@ -1,5 +0,0 @@
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB,SPIFLASH"
-+S:CONFIG_PPC=y
-+S:CONFIG_MPC85xx=y
-+S:CONFIG_TARGET_P1_P2_RDB=y
diff --git a/configs/P2020RDB_defconfig b/configs/P2020RDB_defconfig
deleted file mode 100644
index cc39735..0000000
--- a/configs/P2020RDB_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_SYS_EXTRA_OPTIONS="P2020RDB"
-CONFIG_PPC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_P1_P2_RDB=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 3b201b7..f436a8e 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,10 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+P2020RDB powerpc mpc85xx - - Poonam Aggrwal <poonam.aggrwal at freescale.com>
+P2010RDB powerpc mpc85xx - -
+P1020RDB powerpc mpc85xx - -
+P1011RDB powerpc mpc85xx - -
MPC8360EMDS powerpc mpc83xx - - Dave Liu <daveliu at freescale.com>
MPC8360ERDK powerpc mpc83xx - - Anton Vorontsov <avorontsov at ru.mvista.com>
P3G4 powerpc 74xx_7xx d928664f 2015-01-16 Wolfgang Denk <wd at denx.de>
diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
deleted file mode 100644
index c75638a..0000000
--- a/include/configs/P1_P2_RDB.h
+++ /dev/null
@@ -1,808 +0,0 @@
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * P1 P2 RDB board configuration file
- * This file is intended to address a set of Low End and Ultra Low End
- * Freescale SOCs of QorIQ series(RDB platforms).
- * Currently only P2020RDB
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_36BIT
-#define CONFIG_PHYS_64BIT
-#endif
-
-#ifdef CONFIG_P1011RDB
-#define CONFIG_P1011
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-#ifdef CONFIG_P1020RDB
-#define CONFIG_P1020
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-#ifdef CONFIG_P2010RDB
-#define CONFIG_P2010
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#endif
-#ifdef CONFIG_P2020RDB
-#define CONFIG_P2020
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_MMC_MINIMAL
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SYS_TEXT_BASE 0x11001000
-#define CONFIG_SPL_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_PAD_TO 0x20000
-#define CONFIG_SPL_MAX_SIZE (128 * 1024)
-#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
-#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
-#define CONFIG_SYS_MMC_U_BOOT_OFFS (129 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
-#define CONFIG_SPL_MMC_BOOT
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SYS_TEXT_BASE 0x11001000
-#define CONFIG_SPL_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_PAD_TO 0x20000
-#define CONFIG_SPL_MAX_SIZE (128 * 1024)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
-#define CONFIG_SPL_SPI_BOOT
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
-#endif
-
-#ifdef CONFIG_NAND
-#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SPL_NAND_BOOT
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_NAND_INIT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SPL_MAX_SIZE (128 << 10)
-#define CONFIG_SPL_TEXT_BASE 0xf8f81000
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
-#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10)
-#elif defined(CONFIG_SPL_BUILD)
-#define CONFIG_SPL_INIT_MINIMAL
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_TEXT_BASE 0xff800000
-#define CONFIG_SPL_MAX_SIZE 4096
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000
-#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10)
-#endif /* not CONFIG_TPL_BUILD */
-
-#define CONFIG_SPL_PAD_TO 0x20000
-#define CONFIG_TPL_PAD_TO 0x20000
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE 0x11001000
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
-
-#define CONFIG_PCI 1 /* Enable PCI/PCIE */
-#if defined(CONFIG_PCI)
-#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#endif /* #if defined(CONFIG_PCI) */
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_PCI)
-#define CONFIG_E1000 1 /* E1000 pci Ethernet card*/
-#endif
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1_P2 RDB */
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for P1_P2 RDB */
-
-#if defined(CONFIG_P2020) || defined(CONFIG_P1020)
-#define CONFIG_MP
-#endif
-
-#define CONFIG_HWCONFIG
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x1fffffff
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
-/*
- * Config the L2 Cache as L2 SRAM
-*/
-#if defined(CONFIG_SPL_BUILD)
-#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024)
-#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024)
-#if defined(CONFIG_P2020RDB)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10)
-#else
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10)
-#endif
-#elif defined(CONFIG_NAND)
-#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024)
-#else
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000)
-#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
-#endif /* CONFIG_TPL_BUILD */
-#endif
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#if defined(CONFIG_P1011RDB) || defined(CONFIG_P1020RDB)
-/*
- * P1020 and it's derivatives support max 32bit DDR width
- * So Reduce available DDR size
-*/
-#define CONFIG_SYS_SDRAM_SIZE 512
-#else
-#define CONFIG_SYS_SDRAM_SIZE 1024
-#endif
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00FF0000
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x3fff_ffff DDR 1G cacheablen
- * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
- * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
- *
- * Localbus cacheable (TBD)
- * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable
- *
- * Localbus non-cacheable
- * 0xef00_0000 0xefff_ffff FLASH 16M non-cacheable
- * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
- * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable
- * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
- * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xef000000 /* start of FLASH 16M */
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS 0xfef000000ull
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM 0xff000ff7
-
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-#define CONFIG_MISC_INIT_R
-#define CONFIG_HWCONFIG
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
-
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-
-#define CONFIG_CMD_NAND
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_NAND_FSL_ELBC 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-
-#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#else
-#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#endif
-
-#define CONFIG_SYS_VSC7385_BASE 0xffb00000
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_VSC7385_BASE_PHYS 0xfffb00000ull
-#else
-#define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE
-#endif
-
-#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE) \
- | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
- OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
- OR_GPCM_EHTR | OR_GPCM_EAD)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* new uImage format support */
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 1
-
-#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
-
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_RTC_DS1337_NOOSC
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-#if defined(CONFIG_PCI)
-/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME "Slot 1"
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
-#endif
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
-#endif
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-#undef CONFIG_RTL8139
-
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#define _IO_BASE 0x00000000
-#endif
-
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-
-#endif /* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 1
-
-#define CONFIG_VSC7385_ENET
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-
-/* Vitesse 7385 */
-
-#ifdef CONFIG_VSC7385_ENET
-/* The size of the VSC7385 firmware image */
-#define CONFIG_VSC7385_IMAGE_SIZE 8192
-#endif
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_OFFSET (512 * 0x800)
-#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
-#elif defined(CONFIG_NAND)
-#ifdef CONFIG_TPL_BUILD
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
-#else
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#endif
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET (1024 * 1024)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
-#elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_MMC 1
-
-#ifdef CONFIG_MMC
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_CMD_MMC
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FSL_ESDHC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#ifdef CONFIG_P2020
-#define CONFIG_SYS_FSL_ESDHC_USE_PIO /* P2020 eSDHC DMA is not functional*/
-#endif
-#endif
-
-#define CONFIG_HAS_FSL_DR_USB
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
-#endif
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20)/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_HOSTNAME P2020RDB
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "loadaddr=1000000\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=rootfs.ext2.gz.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=p2020rdb.dtb\0" \
- "bdev=sda1\0" \
- "jffs2nor=mtdblock3\0" \
- "norbootaddr=ef080000\0" \
- "norfdtaddr=ef040000\0" \
- "jffs2nand=mtdblock9\0" \
- "nandbootaddr=100000\0" \
- "nandfdtaddr=80000\0" \
- "nandimgsize=400000\0" \
- "nandfdtsize=80000\0" \
- "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
- "vscfw_addr=ef000000\0" \
- "othbootargs=ramdisk_size=600000\0" \
- "usbfatboot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start;" \
- "fatload usb 0:2 $loadaddr $bootfile;" \
- "fatload usb 0:2 $fdtaddr $fdtfile;" \
- "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- "usbext2boot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start;" \
- "ext2load usb 0:4 $loadaddr $bootfile;" \
- "ext2load usb 0:4 $fdtaddr $fdtfile;" \
- "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- "norboot=setenv bootargs root=/dev/$jffs2nor rw " \
- "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
- "bootm $norbootaddr - $norfdtaddr\0" \
- "nandboot=setenv bootargs root=/dev/$jffs2nand rw rootfstype=jffs2 " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "nand read 2000000 $nandbootaddr $nandimgsize;" \
- "nand read 3000000 $nandfdtaddr $nandfdtsize;" \
- "bootm 2000000 - 3000000;\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "usb start;" \
- "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
- "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
-
-#endif /* __CONFIG_H */
--
1.9.1
More information about the U-Boot
mailing list