[U-Boot] [PATCH] board: tbs2910: Gate clock when switching async clock muxes

[Soeren Moch]

According to the i.MX6Q Reference Manual, clocks must be gated when
switching input clocks of async clock muxes. So use clock gates. Avoid
ldb_di0_ipu clock, because there is no clock gate for this signal.

There have never been any complaints about problems with the old code,
but the new approach is in line with the recommendations in the manual.

Signed-off-by: Soeren Moch <smoch at web.de>
--
Cc: Stefano Babic <sbabic at denx.de>
---
 board/tbs/tbs2910/tbs2910.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)

diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
index dfa430e..42b166d 100644
--- a/board/tbs/tbs2910/tbs2910.c
+++ b/board/tbs/tbs2910/tbs2910.c
@@ -326,21 +326,25 @@ static void setup_display(void)
 	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
 	writel(reg, &ccm->analog_pll_video);
 
-	/* select video pll for ldb_di0_clk */
-	reg = readl(&ccm->cs2cdr);
-	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
-	writel(reg, &ccm->cs2cdr);
+	/* gate ipu1_di0_clk */
+	reg = readl(&ccm->CCGR3);
+	reg &= ~MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &ccm->CCGR3);
 
-	/* select ldb_di0_clk / 7 for ldb_di0_ipu_clk */
-	reg = readl(&ccm->cscmr2);
-	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
-	writel(reg, &ccm->cscmr2);
-
-	/* select ldb_di0_ipu_clk for ipu1_di0_clk -> 65MHz pixclock */
+	/* select video_pll clock / 7  for ipu1_di0_clk -> 65MHz pixclock */
 	reg = readl(&ccm->chsccdr);
-	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
-		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
+		 MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
+		 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+	reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
+	       (6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
+	       (0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 	writel(reg, &ccm->chsccdr);
+
+	/* enable ipu1_di0_clk */
+	reg = readl(&ccm->CCGR3);
+	reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &ccm->CCGR3);
 }
 #endif /* CONFIG_VIDEO_IPUV3 */
 
-- 
1.9.1