[U-Boot] [PATCH v2 07/10] dm: i2c: s3c24x0: adjust to dm-i2c api
Przemyslaw Marczak
p.marczak at samsung.com
Mon Jan 26 16:21:43 CET 2015
This commit adjusts the s3c24x0 driver to new i2c api
based on driver-model. The driver supports standard
and high-speed i2c as previous.
Tested on Trats2, Odroid U3, Arndale, Odroid XU3
Signed-off-by: Przemyslaw Marczak <p.marczak at samsung.com>
Cc: Simon Glass <sjg at chromium.org>
Cc: Heiko Schocher <hs at denx.de>
Cc: Minkyu Kang <mk7.kang at samsung.com>
---
Changes v2:
- use consistent return values on errors
- decrease transaction status timeout, because the previous one was too big
---
drivers/i2c/s3c24x0_i2c.c | 275 +++++++++++++++++++++++++++++++++++++++-------
1 file changed, 233 insertions(+), 42 deletions(-)
diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
index fd328f0..c82640d 100644
--- a/drivers/i2c/s3c24x0_i2c.c
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -9,8 +9,9 @@
* as they seem to have the same I2C controller inside.
* The different address mapping is handled by the s3c24xx.h files below.
*/
-
#include <common.h>
+#include <errno.h>
+#include <dm.h>
#include <fdtdec.h>
#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
#include <asm/arch/clk.h>
@@ -111,9 +112,9 @@
#define I2C_START_STOP 0x20 /* START / STOP */
#define I2C_TXRX_ENA 0x10 /* I2C Tx/Rx enable */
-#define I2C_TIMEOUT_MS 1000 /* 1 second */
+#define I2C_TIMEOUT_MS 10 /* 10 ms */
-#define HSI2C_TIMEOUT_US 100000 /* 100 ms, finer granularity */
+#define HSI2C_TIMEOUT_US 10000 /* 10 ms, finer granularity */
/* To support VCMA9 boards and other who dont define max_i2c_num */
@@ -121,13 +122,23 @@
#define CONFIG_MAX_I2C_NUM 1
#endif
+DECLARE_GLOBAL_DATA_PTR;
+
/*
* For SPL boot some boards need i2c before SDRAM is initialised so force
* variables to live in SRAM
*/
+#ifdef CONFIG_SYS_I2C
static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
__attribute__((section(".data")));
+#endif
+
+enum exynos_i2c_type {
+ EXYNOS_I2C_STD,
+ EXYNOS_I2C_HS,
+};
+#ifdef CONFIG_SYS_I2C
/**
* Get a pointer to the given bus index
*
@@ -147,6 +158,7 @@ static struct s3c24x0_i2c_bus *get_bus(unsigned int bus_idx)
debug("Undefined bus: %d\n", bus_idx);
return NULL;
}
+#endif
#if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
static int GetI2CSDA(void)
@@ -251,6 +263,7 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
}
+#ifdef CONFIG_SYS_I2C
static struct s3c24x0_i2c *get_base_i2c(int bus)
{
#ifdef CONFIG_EXYNOS4
@@ -267,6 +280,7 @@ static struct s3c24x0_i2c *get_base_i2c(int bus)
return s3c24x0_get_base_i2c();
#endif
}
+#endif
static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
{
@@ -326,7 +340,7 @@ static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
return 0;
}
}
- return -1;
+ return -EINVAL;
}
static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
@@ -398,18 +412,20 @@ static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
hsi2c_ch_init(i2c_bus);
}
+#ifdef CONFIG_SYS_I2C
static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
{
struct s3c24x0_i2c *i2c;
struct s3c24x0_i2c_bus *bus;
-
#if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
#endif
ulong start_time = get_timer(0);
- /* By default i2c channel 0 is the current bus */
i2c = get_base_i2c(adap->hwadapnr);
+ bus = &i2c_bus[adap->hwadapnr];
+ if (!bus)
+ return;
/*
* In case the previous transfer is still going, wait to give it a
@@ -470,12 +486,13 @@ static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
#endif
}
#endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */
+
i2c_ch_init(i2c, speed, slaveadd);
- bus = &i2c_bus[adap->hwadapnr];
bus->active = true;
bus->regs = i2c;
}
+#endif /* CONFIG_SYS_I2C */
/*
* Poll the appropriate bit of the fifo status register until the interface is
@@ -698,40 +715,40 @@ static int hsi2c_read(struct exynos5_hsi2c *i2c,
return rv;
}
+#ifdef CONFIG_SYS_I2C
static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap,
- unsigned int speed)
+ unsigned int speed)
+#else
+static int s3c24x0_i2c_set_bus_speed(struct udevice *dev, unsigned int speed)
+#endif
{
struct s3c24x0_i2c_bus *i2c_bus;
+#ifdef CONFIG_SYS_I2C
i2c_bus = get_bus(adap->hwadapnr);
+#else
+ if (!dev)
+ return -ENODEV;
+
+ i2c_bus = dev_get_priv(dev);
+#endif
if (!i2c_bus)
- return -1;
+ return -EFAULT;
i2c_bus->clock_frequency = speed;
if (i2c_bus->is_highspeed) {
if (hsi2c_get_clk_details(i2c_bus))
- return -1;
+ return -EFAULT;
hsi2c_ch_init(i2c_bus);
} else {
i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
- CONFIG_SYS_I2C_S3C24X0_SLAVE);
+ CONFIG_SYS_I2C_S3C24X0_SLAVE);
}
return 0;
}
-#ifdef CONFIG_EXYNOS5
-static void exynos_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
-{
- /* This will override the speed selected in the fdt for that port */
- debug("i2c_init(speed=%u, slaveaddr=0x%x)\n", speed, slaveaddr);
- if (i2c_set_bus_speed(speed))
- printf("i2c_init: failed to init bus %d for speed = %d\n",
- adap->hwadapnr, speed);
-}
-#endif
-
/*
* cmd_type is 0 for write, 1 for read.
*
@@ -844,15 +861,24 @@ bailout:
return result;
}
+#ifdef CONFIG_SYS_I2C
static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
+#else
+static int s3c24x0_i2c_probe(struct udevice *dev, uint chip, uint chip_flags)
+#endif
{
struct s3c24x0_i2c_bus *i2c_bus;
uchar buf[1];
int ret;
+#ifdef CONFIG_SYS_I2C
i2c_bus = get_bus(adap->hwadapnr);
+#else
+ i2c_bus = dev_get_priv(dev);
+#endif
if (!i2c_bus)
- return -1;
+ return -EFAULT;
+
buf[0] = 0;
/*
@@ -871,6 +897,7 @@ static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip)
return ret != I2C_OK;
}
+#ifdef CONFIG_SYS_I2C
static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
int alen, uchar *buffer, int len)
{
@@ -878,9 +905,13 @@ static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
uchar xaddr[4];
int ret;
+ i2c_bus = get_bus(adap->hwadapnr);
+ if (!i2c_bus)
+ return -EFAULT;
+
if (alen > 4) {
debug("I2C read: addr len %d not supported\n", alen);
- return 1;
+ return -EFBIG;
}
if (alen > 0) {
@@ -906,10 +937,6 @@ static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(adap->hwadapnr);
- if (!i2c_bus)
- return -1;
-
if (i2c_bus->is_highspeed)
ret = hsi2c_read(i2c_bus->hsregs, chip, &xaddr[4 - alen],
alen, buffer, len);
@@ -921,7 +948,7 @@ static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
if (i2c_bus->is_highspeed)
exynos5_i2c_reset(i2c_bus);
debug("I2c read failed %d\n", ret);
- return 1;
+ return -EIO;
}
return 0;
}
@@ -933,9 +960,13 @@ static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
uchar xaddr[4];
int ret;
+ i2c_bus = get_bus(adap->hwadapnr);
+ if (!i2c_bus)
+ return -EFAULT;
+
if (alen > 4) {
debug("I2C write: addr len %d not supported\n", alen);
- return 1;
+ return -EINVAL;
}
if (alen > 0) {
@@ -960,10 +991,6 @@ static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
chip |= ((addr >> (alen * 8)) &
CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
- i2c_bus = get_bus(adap->hwadapnr);
- if (!i2c_bus)
- return -1;
-
if (i2c_bus->is_highspeed)
ret = hsi2c_write(i2c_bus->hsregs, chip, &xaddr[4 - alen],
alen, buffer, len, true);
@@ -1010,7 +1037,7 @@ static void process_nodes(const void *blob, int node_list[], int count,
CONFIG_SYS_I2C_S3C24X0_SPEED);
bus->node = node;
bus->bus_num = i;
- exynos_pinmux_config(bus->id, 0);
+ exynos_pinmux_config(PERIPH_ID_I2C0 + bus->id, 0);
/* Mark position as used */
node_list[i] = -1;
@@ -1033,7 +1060,6 @@ void board_i2c_init(const void *blob)
COMPAT_SAMSUNG_EXYNOS5_I2C, node_list,
CONFIG_MAX_I2C_NUM);
process_nodes(blob, node_list, count, 1);
-
}
int i2c_get_bus_num_fdt(int node)
@@ -1046,7 +1072,7 @@ int i2c_get_bus_num_fdt(int node)
}
debug("%s: Can't find any matched I2C bus\n", __func__);
- return -1;
+ return -EINVAL;
}
int i2c_reset_port_fdt(const void *blob, int node)
@@ -1057,18 +1083,18 @@ int i2c_reset_port_fdt(const void *blob, int node)
bus = i2c_get_bus_num_fdt(node);
if (bus < 0) {
debug("could not get bus for node %d\n", node);
- return -1;
+ return bus;
}
i2c_bus = get_bus(bus);
if (!i2c_bus) {
- debug("get_bus() failed for node node %d\n", node);
- return -1;
+ debug("get_bus() failed for node %d\n", node);
+ return -EFAULT;
}
if (i2c_bus->is_highspeed) {
if (hsi2c_get_clk_details(i2c_bus))
- return -1;
+ return -EINVAL;
hsi2c_ch_init(i2c_bus);
} else {
i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency,
@@ -1077,7 +1103,17 @@ int i2c_reset_port_fdt(const void *blob, int node)
return 0;
}
-#endif
+#endif /* CONFIG_OF_CONTROL */
+
+#ifdef CONFIG_EXYNOS5
+static void exynos_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
+{
+ /* This will override the speed selected in the fdt for that port */
+ debug("i2c_init(speed=%u, slaveaddr=0x%x)\n", speed, slaveaddr);
+ if (i2c_set_bus_speed(speed))
+ error("i2c_init: failed to init bus for speed = %d", speed);
+}
+#endif /* CONFIG_EXYNOS5 */
/*
* Register s3c24x0 i2c adapters
@@ -1247,3 +1283,158 @@ U_BOOT_I2C_ADAP_COMPLETE(s3c0, s3c24x0_i2c_init, s3c24x0_i2c_probe,
CONFIG_SYS_I2C_S3C24X0_SPEED,
CONFIG_SYS_I2C_S3C24X0_SLAVE, 0)
#endif
+#endif /* CONFIG_SYS_I2C */
+
+#ifdef CONFIG_DM_I2C
+static int i2c_write_data(struct s3c24x0_i2c_bus *i2c_bus, uchar chip,
+ uchar *buffer, int len, bool end_with_repeated_start)
+{
+ int ret;
+
+ if (!i2c_bus)
+ return -EFAULT;
+
+ if (i2c_bus->is_highspeed) {
+ ret = hsi2c_write(i2c_bus->hsregs, chip, 0, 0,
+ buffer, len, true);
+ if (ret)
+ exynos5_i2c_reset(i2c_bus);
+ } else {
+ ret = i2c_transfer(i2c_bus->regs, I2C_WRITE,
+ chip << 1, 0, 0, buffer, len);
+ }
+
+ return ret != I2C_OK;
+}
+
+static int i2c_read_data(struct s3c24x0_i2c_bus *i2c_bus, uchar chip,
+ uchar *buffer, int len)
+{
+ int ret;
+
+ if (!i2c_bus)
+ return -EFAULT;
+
+ if (i2c_bus->is_highspeed) {
+ ret = hsi2c_read(i2c_bus->hsregs, chip, 0, 0, buffer, len);
+ if (ret)
+ exynos5_i2c_reset(i2c_bus);
+ } else {
+ ret = i2c_transfer(i2c_bus->regs, I2C_READ,
+ chip << 1, 0, 0, buffer, len);
+ }
+
+ return ret != I2C_OK;
+}
+
+static int s3c24x0_i2c_xfer(struct udevice *dev, struct i2c_msg *msg,
+ int nmsgs)
+{
+ struct s3c24x0_i2c_bus *i2c_bus;
+ int ret;
+
+ if (!dev)
+ return -ENODEV;
+
+ i2c_bus = dev_get_priv(dev);
+ if (!i2c_bus)
+ return -EFAULT;
+
+ for (; nmsgs > 0; nmsgs--, msg++) {
+ bool next_is_read = nmsgs > 1 && (msg[1].flags & I2C_M_RD);
+
+ if (msg->flags & I2C_M_RD) {
+ ret = i2c_read_data(i2c_bus, msg->addr, msg->buf,
+ msg->len);
+ } else {
+ ret = i2c_write_data(i2c_bus, msg->addr, msg->buf,
+ msg->len, next_is_read);
+ }
+ if (ret)
+ return -EREMOTEIO;
+ }
+
+ return 0;
+}
+
+static int s3c_i2c_ofdata_to_platdata(struct udevice *dev)
+{
+ const void *blob = gd->fdt_blob;
+ struct s3c24x0_i2c_bus *i2c_bus;
+ int node;
+
+ if (!dev) {
+ error("%s: no such device!", dev->name);
+ return -ENODEV;
+ }
+
+ i2c_bus = dev_get_priv(dev);
+ if (!i2c_bus) {
+ error("%s: i2c bus not allocated!", dev->name);
+ return -EFAULT;
+ }
+
+ if (!dev->of_id) {
+ error("%s: no compat ids!", dev->name);
+ return -EINVAL;
+ }
+ i2c_bus->is_highspeed = dev->of_id->data;
+
+ node = dev->of_offset;
+
+ if (i2c_bus->is_highspeed) {
+ i2c_bus->hsregs = (struct exynos5_hsi2c *)
+ fdtdec_get_addr(blob, node, "reg");
+ } else {
+ i2c_bus->regs = (struct s3c24x0_i2c *)
+ fdtdec_get_addr(blob, node, "reg");
+ }
+
+ i2c_bus->id = pinmux_decode_periph_id(blob, node);
+
+ i2c_bus->clock_frequency = fdtdec_get_int(blob, node,
+ "clock-frequency",
+ CONFIG_SYS_I2C_S3C24X0_SPEED);
+ i2c_bus->node = node;
+ i2c_bus->bus_num = dev->seq;
+
+ exynos_pinmux_config(i2c_bus->id, i2c_bus->is_highspeed);
+
+ i2c_bus->active = true;
+
+ return 0;
+}
+
+static int s3c_i2c_child_pre_probe(struct udevice *dev)
+{
+ struct dm_i2c_chip *i2c_chip = dev_get_parentdata(dev);
+
+ if (dev->of_offset == -1)
+ return 0;
+ return i2c_chip_ofdata_to_platdata(gd->fdt_blob, dev->of_offset,
+ i2c_chip);
+}
+
+static const struct dm_i2c_ops s3c_i2c_ops = {
+ .xfer = s3c24x0_i2c_xfer,
+ .probe_chip = s3c24x0_i2c_probe,
+ .set_bus_speed = s3c24x0_i2c_set_bus_speed,
+};
+
+static const struct udevice_id s3c_i2c_ids[] = {
+ { .compatible = "samsung,s3c2440-i2c", .data = EXYNOS_I2C_STD },
+ { .compatible = "samsung,exynos5-hsi2c", .data = EXYNOS_I2C_HS },
+ { }
+};
+
+U_BOOT_DRIVER(i2c_s3c) = {
+ .name = "i2c_s3c",
+ .id = UCLASS_I2C,
+ .of_match = s3c_i2c_ids,
+ .ofdata_to_platdata = s3c_i2c_ofdata_to_platdata,
+ .per_child_auto_alloc_size = sizeof(struct dm_i2c_chip),
+ .child_pre_probe = s3c_i2c_child_pre_probe,
+ .priv_auto_alloc_size = sizeof(struct s3c24x0_i2c_bus),
+ .ops = &s3c_i2c_ops,
+};
+#endif /* CONFIG_DM_I2C */
--
1.9.1
More information about the U-Boot
mailing list