[U-Boot] [PATCH v2 16/22] x86: Allow FSP Kconfig settings for all x86

[Simon Glass]

While queensbay is the first chip with these settings, others will want to
use them too. Make them common.

Signed-off-by: Simon Glass <sjg at chromium.org>
Reviewed-by: Bin Meng <bmeng.cn at gmail.com>
---

Changes in v2: None

 arch/x86/Kconfig               | 38 ++++++++++++++++++++++++++++++++++++++
 arch/x86/cpu/queensbay/Kconfig | 38 --------------------------------------
 2 files changed, 38 insertions(+), 38 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index bda7a0e..1b7955b 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -344,6 +344,44 @@ config TSC_FREQ_IN_MHZ
 	help
 	  The running frequency in MHz of Time-Stamp Counter (TSC).
 
+config HAVE_FSP
+	bool "Add an Firmware Support Package binary"
+	help
+	  Select this option to add an Firmware Support Package binary to
+	  the resulting U-Boot image. It is a binary blob which U-Boot uses
+	  to set up SDRAM and other chipset specific initialization.
+
+	  Note: Without this binary U-Boot will not be able to set up its
+	  SDRAM so will not boot.
+
+config FSP_FILE
+	string "Firmware Support Package binary filename"
+	depends on HAVE_FSP
+	default "fsp.bin"
+	help
+	  The filename of the file to use as Firmware Support Package binary
+	  in the board directory.
+
+config FSP_ADDR
+	hex "Firmware Support Package binary location"
+	depends on HAVE_FSP
+	default 0xfffc0000
+	help
+	  FSP is not Position Independent Code (PIC) and the whole FSP has to
+	  be rebased if it is placed at a location which is different from the
+	  perferred base address specified during the FSP build. Use Intel's
+	  Binary Configuration Tool (BCT) to do the rebase.
+
+	  The default base address of 0xfffc0000 indicates that the binary must
+	  be located at offset 0xc0000 from the beginning of a 1MB flash device.
+
+config FSP_TEMP_RAM_ADDR
+	hex
+	default 0x2000000
+	help
+	  Stack top address which is used in FspInit after DRAM is ready and
+	  CAR is disabled.
+
 source "arch/x86/cpu/coreboot/Kconfig"
 
 source "arch/x86/cpu/ivybridge/Kconfig"
diff --git a/arch/x86/cpu/queensbay/Kconfig b/arch/x86/cpu/queensbay/Kconfig
index f6b5201..397e599 100644
--- a/arch/x86/cpu/queensbay/Kconfig
+++ b/arch/x86/cpu/queensbay/Kconfig
@@ -11,44 +11,6 @@ config INTEL_QUEENSBAY
 
 if INTEL_QUEENSBAY
 
-config HAVE_FSP
-	bool "Add an Firmware Support Package binary"
-	help
-	  Select this option to add an Firmware Support Package binary to
-	  the resulting U-Boot image. It is a binary blob which U-Boot uses
-	  to set up SDRAM and other chipset specific initialization.
-
-	  Note: Without this binary U-Boot will not be able to set up its
-	  SDRAM so will not boot.
-
-config FSP_FILE
-	string "Firmware Support Package binary filename"
-	depends on HAVE_FSP
-	default "fsp.bin"
-	help
-	  The filename of the file to use as Firmware Support Package binary
-	  in the board directory.
-
-config FSP_ADDR
-	hex "Firmware Support Package binary location"
-	depends on HAVE_FSP
-	default 0xfffc0000
-	help
-	  FSP is not Position Independent Code (PIC) and the whole FSP has to
-	  be rebased if it is placed at a location which is different from the
-	  perferred base address specified during the FSP build. Use Intel's
-	  Binary Configuration Tool (BCT) to do the rebase.
-
-	  The default base address of 0xfffc0000 indicates that the binary must
-	  be located at offset 0xc0000 from the beginning of a 1MB flash device.
-
-config FSP_TEMP_RAM_ADDR
-	hex
-	default 0x2000000
-	help
-	  Stack top address which is used in FspInit after DRAM is ready and
-	  CAR is disabled.
-
 config HAVE_CMC
 	bool "Add a Chipset Micro Code state machine binary"
 	help
-- 
2.2.0.rc0.207.ga3a616c