[U-Boot] [PATCH 1/4] mx6sx: pins: Enable SION for I2C3 iomux setting

[Stefano Babic]

Hi,

On 12/01/2015 11:37, Nikolay Dimitrov wrote:
> Hi Ye.Li,
> 
> On 01/12/2015 10:46 AM, Ye.Li wrote:
>> The I2C SDA and SCL require the IOMUX SION bit set to get input signal.
>>
>> Signed-off-by: Ye.Li <B37916 at freescale.com>
>> ---
>>   arch/arm/include/asm/arch-mx6/mx6sx_pins.h |    4 ++--
>>   1 files changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/include/asm/arch-mx6/mx6sx_pins.h
>> b/arch/arm/include/asm/arch-mx6/mx6sx_pins.h
>> index 7c6c1e8..da8c698 100644
>> --- a/arch/arm/include/asm/arch-mx6/mx6sx_pins.h
>> +++ b/arch/arm/include/asm/arch-mx6/mx6sx_pins.h
>> @@ -420,7 +420,7 @@ enum {
>>
>>        MX6_PAD_KEY_COL4__KPP_COL_4                            =
>> IOMUX_PAD(0x03FC, 0x00B4, 0, 0x0000, 0, 0),
>>        MX6_PAD_KEY_COL4__ENET2_MDC                            =
>> IOMUX_PAD(0x03FC, 0x00B4, 1, 0x0000, 0, 0),
>> -     MX6_PAD_KEY_COL4__I2C3_SCL                             =
>> IOMUX_PAD(0x03FC, 0x00B4, 2, 0x07B8, 2, 0),
>> +     MX6_PAD_KEY_COL4__I2C3_SCL                             =
>> IOMUX_PAD(0x03FC, 0x00B4, IOMUX_CONFIG_SION | 2, 0x07B8, 2, 0),
>>        MX6_PAD_KEY_COL4__USDHC2_LCTL                          =
>> IOMUX_PAD(0x03FC, 0x00B4, 3, 0x0000, 0, 0),
>>        MX6_PAD_KEY_COL4__AUDMUX_AUD5_RXC                      =
>> IOMUX_PAD(0x03FC, 0x00B4, 4, 0x0664, 0, 0),
>>        MX6_PAD_KEY_COL4__GPIO2_IO_14                          =
>> IOMUX_PAD(0x03FC, 0x00B4, 5, 0x0000, 0, 0),
>> @@ -467,7 +467,7 @@ enum {
>>
>>        MX6_PAD_KEY_ROW4__KPP_ROW_4                            =
>> IOMUX_PAD(0x0410, 0x00C8, 0, 0x0000, 0, 0),
>>        MX6_PAD_KEY_ROW4__ENET2_MDIO                           =
>> IOMUX_PAD(0x0410, 0x00C8, 1, 0x0770, 3, 0),
>> -     MX6_PAD_KEY_ROW4__I2C3_SDA                             =
>> IOMUX_PAD(0x0410, 0x00C8, 2, 0x07BC, 2, 0),
>> +     MX6_PAD_KEY_ROW4__I2C3_SDA                             =
>> IOMUX_PAD(0x0410, 0x00C8, IOMUX_CONFIG_SION | 2, 0x07BC, 2, 0),
>>        MX6_PAD_KEY_ROW4__USDHC1_LCTL                          =
>> IOMUX_PAD(0x0410, 0x00C8, 3, 0x0000, 0, 0),
>>        MX6_PAD_KEY_ROW4__AUDMUX_AUD5_RXFS                     =
>> IOMUX_PAD(0x0410, 0x00C8, 4, 0x0668, 0, 0),
>>        MX6_PAD_KEY_ROW4__GPIO2_IO_19                          =
>> IOMUX_PAD(0x0410, 0x00C8, 5, 0x0000, 0, 0),
>>
> 
> Usually the SCL is output-only, driven by the I2C master. Why do you
> need to enable SION bit on SCL, if the pin will be used as output-only?
> 

Right - I do not see why SION should be set.

Regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================