[U-Boot] [PATCH 14/20] arm: rpi: Bring in kernel device tree files
Simon Glass
sjg at chromium.org
Wed Jul 8 04:53:46 CEST 2015
Bring in the device tree files from Linux v4.1.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/dts/Makefile | 2 +
arch/arm/dts/bcm2835-rpi-b.dts | 23 ++++
arch/arm/dts/bcm2835-rpi.dtsi | 51 +++++++++
arch/arm/dts/bcm2835.dtsi | 192 ++++++++++++++++++++++++++++++++++
include/dt-bindings/pinctrl/bcm2835.h | 27 +++++
5 files changed, 295 insertions(+)
create mode 100644 arch/arm/dts/bcm2835-rpi-b.dts
create mode 100644 arch/arm/dts/bcm2835-rpi.dtsi
create mode 100644 arch/arm/dts/bcm2835.dtsi
create mode 100644 include/dt-bindings/pinctrl/bcm2835.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 9c735c6..b284a2d 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -49,6 +49,8 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
zynq-zc770-xm013.dtb
dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb
+dtb-$(CONFIG_ARCH_BCM283X) += bcm2835-rpi-b.dtb
+
dtb-$(CONFIG_ARCH_SOCFPGA) += \
socfpga_arria5_socdk.dtb \
socfpga_cyclone5_socdk.dtb \
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
new file mode 100644
index 0000000..ee89b79
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -0,0 +1,23 @@
+/dts-v1/;
+#include "bcm2835-rpi.dtsi"
+
+/ {
+ compatible = "raspberrypi,model-b", "brcm,bcm2835";
+ model = "Raspberry Pi Model B";
+
+ leds {
+ act {
+ gpios = <&gpio 16 1>;
+ };
+ };
+};
+
+&gpio {
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+
+ /* I2S interface */
+ i2s_alt2: i2s_alt2 {
+ brcm,pins = <28 29 30 31>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+};
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
new file mode 100644
index 0000000..46780bb
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -0,0 +1,51 @@
+#include "bcm2835.dtsi"
+
+/ {
+ memory {
+ reg = <0 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ act {
+ label = "ACT";
+ default-state = "keep";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&gpio {
+ pinctrl-names = "default";
+
+ gpioout: gpioout {
+ brcm,pins = <6>;
+ brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+ };
+
+ alt0: alt0 {
+ brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ alt3: alt3 {
+ brcm,pins = <48 49 50 51 52 53>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&sdhci {
+ status = "okay";
+ bus-width = <4>;
+};
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
new file mode 100644
index 0000000..301c73f
--- /dev/null
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -0,0 +1,192 @@
+#include <dt-bindings/pinctrl/bcm2835.h>
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "brcm,bcm2835";
+ model = "BCM2835";
+ interrupt-parent = <&intc>;
+
+ chosen {
+ bootargs = "earlyprintk console=ttyAMA0";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x7e000000 0x20000000 0x02000000>;
+ dma-ranges = <0x40000000 0x00000000 0x20000000>;
+
+ timer at 7e003000 {
+ compatible = "brcm,bcm2835-system-timer";
+ reg = <0x7e003000 0x1000>;
+ interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+ clock-frequency = <1000000>;
+ };
+
+ dma: dma at 7e007000 {
+ compatible = "brcm,bcm2835-dma";
+ reg = <0x7e007000 0xf00>;
+ interrupts = <1 16>,
+ <1 17>,
+ <1 18>,
+ <1 19>,
+ <1 20>,
+ <1 21>,
+ <1 22>,
+ <1 23>,
+ <1 24>,
+ <1 25>,
+ <1 26>,
+ <1 27>,
+ <1 28>;
+
+ #dma-cells = <1>;
+ brcm,dma-channel-mask = <0x7f35>;
+ };
+
+ intc: interrupt-controller at 7e00b200 {
+ compatible = "brcm,bcm2835-armctrl-ic";
+ reg = <0x7e00b200 0x200>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ watchdog at 7e100000 {
+ compatible = "brcm,bcm2835-pm-wdt";
+ reg = <0x7e100000 0x28>;
+ };
+
+ rng at 7e104000 {
+ compatible = "brcm,bcm2835-rng";
+ reg = <0x7e104000 0x10>;
+ };
+
+ mailbox: mailbox at 7e00b800 {
+ compatible = "brcm,bcm2835-mbox";
+ reg = <0x7e00b880 0x40>;
+ interrupts = <0 1>;
+ #mbox-cells = <0>;
+ };
+
+ gpio: gpio at 7e200000 {
+ compatible = "brcm,bcm2835-gpio";
+ reg = <0x7e200000 0xb4>;
+ /*
+ * The GPIO IP block is designed for 3 banks of GPIOs.
+ * Each bank has a GPIO interrupt for itself.
+ * There is an overall "any bank" interrupt.
+ * In order, these are GIC interrupts 17, 18, 19, 20.
+ * Since the BCM2835 only has 2 banks, the 2nd bank
+ * interrupt output appears to be mirrored onto the
+ * 3rd bank's interrupt signal.
+ * So, a bank0 interrupt shows up on 17, 20, and
+ * a bank1 interrupt shows up on 18, 19, 20!
+ */
+ interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart at 7e201000 {
+ compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+ reg = <0x7e201000 0x1000>;
+ interrupts = <2 25>;
+ clock-frequency = <3000000>;
+ arm,primecell-periphid = <0x00241011>;
+ };
+
+ i2s: i2s at 7e203000 {
+ compatible = "brcm,bcm2835-i2s";
+ reg = <0x7e203000 0x20>,
+ <0x7e101098 0x02>;
+
+ dmas = <&dma 2>,
+ <&dma 3>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi: spi at 7e204000 {
+ compatible = "brcm,bcm2835-spi";
+ reg = <0x7e204000 0x1000>;
+ interrupts = <2 22>;
+ clocks = <&clk_spi>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c0: i2c at 7e205000 {
+ compatible = "brcm,bcm2835-i2c";
+ reg = <0x7e205000 0x1000>;
+ interrupts = <2 21>;
+ clocks = <&clk_i2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ sdhci: sdhci at 7e300000 {
+ compatible = "brcm,bcm2835-sdhci";
+ reg = <0x7e300000 0x100>;
+ interrupts = <2 30>;
+ clocks = <&clk_mmc>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 7e804000 {
+ compatible = "brcm,bcm2835-i2c";
+ reg = <0x7e804000 0x1000>;
+ interrupts = <2 21>;
+ clocks = <&clk_i2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usb at 7e980000 {
+ compatible = "brcm,bcm2835-usb";
+ reg = <0x7e980000 0x10000>;
+ interrupts = <1 9>;
+ };
+
+ arm-pmu {
+ compatible = "arm,arm1176-pmu";
+ };
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clk_mmc: clock at 0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-output-names = "mmc";
+ clock-frequency = <100000000>;
+ };
+
+ clk_i2c: clock at 1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ #clock-cells = <0>;
+ clock-output-names = "i2c";
+ clock-frequency = <250000000>;
+ };
+
+ clk_spi: clock at 2 {
+ compatible = "fixed-clock";
+ reg = <2>;
+ #clock-cells = <0>;
+ clock-output-names = "spi";
+ clock-frequency = <250000000>;
+ };
+ };
+};
diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h
new file mode 100644
index 0000000..6f0bc37
--- /dev/null
+++ b/include/dt-bindings/pinctrl/bcm2835.h
@@ -0,0 +1,27 @@
+/*
+ * Header providing constants for bcm2835 pinctrl bindings.
+ *
+ * Copyright (C) 2015 Stefan Wahren <stefan.wahren at i2se.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_BCM2835_H__
+#define __DT_BINDINGS_PINCTRL_BCM2835_H__
+
+/* brcm,function property */
+#define BCM2835_FSEL_GPIO_IN 0
+#define BCM2835_FSEL_GPIO_OUT 1
+#define BCM2835_FSEL_ALT5 2
+#define BCM2835_FSEL_ALT4 3
+#define BCM2835_FSEL_ALT0 4
+#define BCM2835_FSEL_ALT1 5
+#define BCM2835_FSEL_ALT2 6
+#define BCM2835_FSEL_ALT3 7
+
+#endif /* __DT_BINDINGS_PINCTRL_BCM2835_H__ */
--
2.4.3.573.g4eafbef
More information about the U-Boot
mailing list