[U-Boot] [PATCH 03/11] imx: usb: ehci-mx7 add usb driver for i.MX7D

[Adrian Alonso]

* Add support for usb driver for i.MX7D SoC

Signed-off-by: Adrian Alonso <aalonso at freescale.com>
Signed-off-by: Ye.Li <B37916 at freescale.com>
Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
---
 drivers/usb/host/Makefile   |   1 +
 drivers/usb/host/ehci-mx7.c | 103 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 104 insertions(+)
 create mode 100644 drivers/usb/host/ehci-mx7.c

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 4d35d3e..7267160 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
 obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
 obj-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
 obj-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
+obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx7.o
 obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
 obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
diff --git a/drivers/usb/host/ehci-mx7.c b/drivers/usb/host/ehci-mx7.c
new file mode 100644
index 0000000..7429d62
--- /dev/null
+++ b/drivers/usb/host/ehci-mx7.c
@@ -0,0 +1,103 @@
+/*
+ * Copyright (c) 2009 Daniel Mack <daniel at caiaq.de>
+ * Copyright (C) 2010-2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <errno.h>
+#include <linux/compiler.h>
+#include <usb/ehci-fsl.h>
+#include <asm/io.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
+#include <asm/imx-common/iomux-v3.h>
+
+#include "ehci.h"
+
+#define USB_NC_OFFSET	0x200
+
+#define UCTRL_PM		(1 << 9)	/* OTG Power Mask */
+#define UCTRL_OVER_CUR_POL	(1 << 8) /* OTG Polarity of Overcurrent */
+#define UCTRL_OVER_CUR_DIS	(1 << 7) /* Disable OTG Overcurrent Detection */
+
+/* USBCMD */
+#define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
+#define UCMD_RESET		(1 << 1) /* controller reset */
+
+/* Base address for this IP block is 0x02184800 */
+struct usbnc_regs {
+	u32	ctrl1;
+	u32 ctrl2;
+	u32 reserve1[11];
+	u32 phy_ctrl2;
+	u32 reserve2[6];
+	u32 adp_cfg1;
+	u32 reserve3;
+	u32 adp_status;
+};
+
+static void usb_oc_config(int index)
+{
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * index) + USB_NC_OFFSET);
+	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
+	u32 val;
+
+	val = __raw_readl(ctrl);
+	val |= UCTRL_OVER_CUR_POL;
+	__raw_writel(val, ctrl);
+
+	val = __raw_readl(ctrl);
+	val |= (UCTRL_OVER_CUR_DIS | UCTRL_PM);
+	__raw_writel(val, ctrl);
+}
+
+int __weak board_ehci_hcd_init(int port)
+{
+	return 0;
+}
+
+int __weak board_ehci_power(int port, int on)
+{
+	return 0;
+}
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
+		(0x10000 * index));
+
+	if (index > 3)
+		return -EINVAL;
+	enable_usboh3_clk(1);
+	mdelay(1);
+
+	/* Do board specific initialization */
+	board_ehci_hcd_init(index);
+
+	usb_oc_config(index);
+
+	*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+	*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
+			HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+	board_ehci_power(index, (init == USB_INIT_DEVICE) ? 0 : 1);
+	if (init == USB_INIT_DEVICE)
+		return 0;
+	setbits_le32(&ehci->usbmode, CM_HOST);
+	__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
+	setbits_le32(&ehci->portsc, USB_EN);
+
+	mdelay(10);
+
+	return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+	return 0;
+}
-- 
2.1.4