[U-Boot] [PATCH 02/15][v3] imx: usb: ehci-mx7 add usb driver for i.MX7D

[Marek Vasut]

On Thursday, July 23, 2015 at 12:24:22 AM, Adrian Alonso wrote:
> * Add support for usb driver for i.MX7D SoC

Please drop this asterisk, it's pointless.

> Signed-off-by: Adrian Alonso <aalonso at freescale.com>
> Signed-off-by: Ye.Li <B37916 at freescale.com>
> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
> ---
> Changes for V2: Resend
> Changes for V3:
> - Integrate review obserbations
> - Add comments for fucntions board_ehci_hcd_init/board_ehci_power
> 
>  drivers/usb/host/Makefile   |   1 +
>  drivers/usb/host/ehci-mx7.c | 112
> ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 113
> insertions(+)
>  create mode 100644 drivers/usb/host/ehci-mx7.c
> 
> diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> index 4d35d3e..7267160 100644
> --- a/drivers/usb/host/Makefile
> +++ b/drivers/usb/host/Makefile
> @@ -36,6 +36,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
>  obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
>  obj-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
>  obj-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
> +obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx7.o
>  obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
>  obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
>  obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
> diff --git a/drivers/usb/host/ehci-mx7.c b/drivers/usb/host/ehci-mx7.c
> new file mode 100644
> index 0000000..40aed07
> --- /dev/null
> +++ b/drivers/usb/host/ehci-mx7.c
> @@ -0,0 +1,112 @@
> +/*
> + * Copyright (c) 2009 Daniel Mack <daniel at caiaq.de>
> + * Copyright (C) 2010-2015 Freescale Semiconductor, Inc.
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <usb.h>
> +#include <errno.h>
> +#include <linux/compiler.h>
> +#include <usb/ehci-fsl.h>
> +#include <asm/io.h>
> +#include <asm/arch/crm_regs.h>
> +#include <asm/arch/clock.h>
> +#include <asm/imx-common/iomux-v3.h>
> +
> +#include "ehci.h"
> +
> +#define USB_NC_OFFSET	0x200
> +
> +#define UCTRL_PM		(1 << 9) /* OTG Power Mask */
> +#define UCTRL_OVER_CUR_POL	(1 << 8) /* OTG Polarity of Overcurrent */
> +#define UCTRL_OVER_CUR_DIS	(1 << 7) /* Disable OTG Overcurrent Detection
> */ +
> +/* USBCMD */
> +#define UCMD_RUN_STOP		(1 << 0) /* controller run/stop */
> +#define UCMD_RESET		(1 << 1) /* controller reset */
> +
> +/* Base address for this IP block is 0x02184800 */
> +struct usbnc_regs {
> +	u32 ctrl1;
> +	u32 ctrl2;
> +	u32 reserve1[11];
> +	u32 phy_ctrl2;
> +	u32 reserve2[6];
> +	u32 adp_cfg1;
> +	u32 reserve3;
> +	u32 adp_status;
> +};
> +
> +static void usb_oc_config(int index)
> +{
> +	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
> +			(0x10000 * index) + USB_NC_OFFSET);
> +	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
> +
> +	setbits_le32(ctrl, UCTRL_OVER_CUR_POL);
> +	setbits_le32(ctrl, UCTRL_OVER_CUR_DIS | UCTRL_PM);
> +}
> +
> +/*

This is not valid kerneldoc, see documentation here:

https://www.kernel.org/doc/Documentation/kernel-doc-nano-HOWTO.txt

> + * board_ehci_hcd_init - set usb vbus voltage
> + * Setup iomux pad to setup supply vbus voltage for usb otg port.
> + * Machine board file overrides board_ehci_hcd_init
> + * @port: usb otg port
> + *
> + */

Other than that, it's cool. Can you please re-send it in-reply-to to
the original series ?

Thanks!

Best regards,
Marek Vasut