[U-Boot] [PATCH v2 2/2] warp: Add MAX77696 support

[Stefano Babic]

On 22/07/2015 02:47, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam at freescale.com>
> 
> Warp has a MAX77696 PMIC connected via I2C1 bus.
> 
> Add support for it.                                                                
> 
> Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
> ---
> Changes since v1:
> - None
> 
>  board/warp/warp.c      | 50 ++++++++++++++++++++++++++++++++++++++++++++++++++
>  include/configs/warp.h | 11 +++++++++++
>  2 files changed, 61 insertions(+)
> 
> diff --git a/board/warp/warp.c b/board/warp/warp.c
> index 21ac5e7..49dfdb6 100644
> --- a/board/warp/warp.c
> +++ b/board/warp/warp.c
> @@ -15,13 +15,17 @@
>  #include <asm/arch/sys_proto.h>
>  #include <asm/gpio.h>
>  #include <asm/imx-common/iomux-v3.h>
> +#include <asm/imx-common/mxc_i2c.h>
>  #include <asm/io.h>
>  #include <linux/sizes.h>
>  #include <common.h>
>  #include <watchdog.h>
>  #include <fsl_esdhc.h>
> +#include <i2c.h>
>  #include <mmc.h>
>  #include <usb.h>
> +#include <power/pmic.h>
> +#include <power/max77696_pmic.h>
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -35,6 +39,11 @@ DECLARE_GLOBAL_DATA_PTR;
>  	PAD_CTL_SRE_FAST  | PAD_CTL_HYS | \
>  	PAD_CTL_LVE)
>  
> +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
> +		      PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |	\
> +		      PAD_CTL_DSE_40ohm | PAD_CTL_HYS |		\
> +		      PAD_CTL_ODE | PAD_CTL_SRE_FAST)
> +
>  int dram_init(void)
>  {
>  	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> @@ -88,6 +97,45 @@ int board_usb_phy_mode(int port)
>  	return USB_INIT_DEVICE;
>  }
>  
> +/* I2C1 for PMIC */
> +#define I2C_PMIC	0
> +#define PC	MUX_PAD_CTRL(I2C_PAD_CTRL)
> +struct i2c_pads_info i2c_pad_info1 = {
> +	.sda = {
> +		.i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC,
> +		.gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC,
> +		.gp = IMX_GPIO_NR(3, 13),
> +	},
> +	.scl = {
> +		.i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC,
> +		.gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC,
> +		.gp = IMX_GPIO_NR(3, 12),
> +	},
> +};
> +
> +int power_init_board(void)
> +{
> +	struct pmic *p;
> +	int ret;
> +	unsigned int reg;
> +
> +	ret = power_max77696_init(I2C_PMIC);
> +	if (ret)
> +		return ret;
> +
> +	p = pmic_get("MAX77696");
> +	if (!p)
> +		return -EINVAL;
> +
> +	ret = pmic_reg_read(p, CID, &reg);
> +	if (ret)
> +		return ret;
> +
> +	printf("PMIC:  MAX77696 detected, rev=0x%x\n", reg);
> +
> +	return pmic_probe(p);
> +}
> +
>  int board_early_init_f(void)
>  {
>  	setup_iomux_uart();
> @@ -99,6 +147,8 @@ int board_init(void)
>  	/* address of boot parameters */
>  	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>  
> +	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> +
>  	return 0;
>  }
>  
> diff --git a/include/configs/warp.h b/include/configs/warp.h
> index 48e2058..f38f781 100644
> --- a/include/configs/warp.h
> +++ b/include/configs/warp.h
> @@ -98,6 +98,17 @@
>  #define CONFIG_CMD_FUSE
>  #define CONFIG_MXC_OCOTP
>  
> +/* I2C Configs */
> +#define CONFIG_CMD_I2C
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_SPEED		  100000
> +
> +/* PMIC */
> +#define CONFIG_POWER
> +#define CONFIG_POWER_I2C
> +#define CONFIG_POWER_MAX77696
> +
>  #define CONFIG_EXTRA_ENV_SETTINGS \
>  	"script=boot.scr\0" \
>  	"image=zImage\0" \
> 

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic
-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================