[U-Boot] [PATCH 161/172] ddr: altera: Clean up rw_mgr_mem_calibrate_write_test() part 1
Marek Vasut
marex at denx.de
Mon Jul 27 22:52:04 CEST 2015
Move code around to get rid of the forward declaration. No change
to the actual code.
Signed-off-by: Marek Vasut <marex at denx.de>
---
drivers/ddr/altera/sequencer.c | 406 ++++++++++++++++++++---------------------
1 file changed, 201 insertions(+), 205 deletions(-)
diff --git a/drivers/ddr/altera/sequencer.c b/drivers/ddr/altera/sequencer.c
index 99cd2b2..659c0d8 100644
--- a/drivers/ddr/altera/sequencer.c
+++ b/drivers/ddr/altera/sequencer.c
@@ -80,10 +80,6 @@ struct gbl_type *gbl;
struct param_type *param;
uint32_t curr_shadow_reg;
-static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn,
- uint32_t write_group, uint32_t use_dm,
- uint32_t all_correct, uint32_t *bit_chk, uint32_t all_ranks);
-
static void set_failing_group_stage(uint32_t group, uint32_t stage,
uint32_t substage)
{
@@ -1036,6 +1032,207 @@ static void rw_mgr_mem_handoff(void)
*/
}
+/*
+ * issue write test command.
+ * two variants are provided. one that just tests a write pattern and
+ * another that tests datamask functionality.
+ */
+static void rw_mgr_mem_calibrate_write_test_issue(uint32_t group,
+ uint32_t test_dm)
+{
+ uint32_t mcc_instruction;
+ uint32_t quick_write_mode = (((STATIC_CALIB_STEPS) & CALIB_SKIP_WRITES) &&
+ ENABLE_SUPER_QUICK_CALIBRATION);
+ uint32_t rw_wl_nop_cycles;
+ uint32_t addr;
+
+ /*
+ * Set counter and jump addresses for the right
+ * number of NOP cycles.
+ * The number of supported NOP cycles can range from -1 to infinity
+ * Three different cases are handled:
+ *
+ * 1. For a number of NOP cycles greater than 0, the RW Mgr looping
+ * mechanism will be used to insert the right number of NOPs
+ *
+ * 2. For a number of NOP cycles equals to 0, the micro-instruction
+ * issuing the write command will jump straight to the
+ * micro-instruction that turns on DQS (for DDRx), or outputs write
+ * data (for RLD), skipping
+ * the NOP micro-instruction all together
+ *
+ * 3. A number of NOP cycles equal to -1 indicates that DQS must be
+ * turned on in the same micro-instruction that issues the write
+ * command. Then we need
+ * to directly jump to the micro-instruction that sends out the data
+ *
+ * NOTE: Implementing this mechanism uses 2 RW Mgr jump-counters
+ * (2 and 3). One jump-counter (0) is used to perform multiple
+ * write-read operations.
+ * one counter left to issue this command in "multiple-group" mode
+ */
+
+ rw_wl_nop_cycles = gbl->rw_wl_nop_cycles;
+
+ if (rw_wl_nop_cycles == -1) {
+ /*
+ * CNTR 2 - We want to execute the special write operation that
+ * turns on DQS right away and then skip directly to the
+ * instruction that sends out the data. We set the counter to a
+ * large number so that the jump is always taken.
+ */
+ writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+
+ /* CNTR 3 - Not used */
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0_WL_1;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_DATA,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ }
+ } else if (rw_wl_nop_cycles == 0) {
+ /*
+ * CNTR 2 - We want to skip the NOP operation and go straight
+ * to the DQS enable instruction. We set the counter to a large
+ * number so that the jump is always taken.
+ */
+ writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+
+ /* CNTR 3 - Not used */
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_DQS,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ }
+ } else {
+ /*
+ * CNTR 2 - In this case we want to execute the next instruction
+ * and NOT take the jump. So we set the counter to 0. The jump
+ * address doesn't count.
+ */
+ writel(0x0, &sdr_rw_load_mgr_regs->load_cntr2);
+ writel(0x0, &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+
+ /*
+ * CNTR 3 - Set the nop counter to the number of cycles we
+ * need to loop for, minus 1.
+ */
+ writel(rw_wl_nop_cycles - 1, &sdr_rw_load_mgr_regs->load_cntr3);
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ }
+ }
+
+ writel(0, SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RESET_READ_DATAPATH_OFFSET);
+
+ if (quick_write_mode)
+ writel(0x08, &sdr_rw_load_mgr_regs->load_cntr0);
+ else
+ writel(0x40, &sdr_rw_load_mgr_regs->load_cntr0);
+
+ writel(mcc_instruction, &sdr_rw_load_jump_mgr_regs->load_jump_add0);
+
+ /*
+ * CNTR 1 - This is used to ensure enough time elapses
+ * for read data to come back.
+ */
+ writel(0x30, &sdr_rw_load_mgr_regs->load_cntr1);
+
+ if (test_dm) {
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add1);
+ } else {
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_WAIT,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add1);
+ }
+
+ addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_SINGLE_GROUP_OFFSET;
+ writel(mcc_instruction, addr + (group << 2));
+}
+
+/* Test writes, can check for a single bit pass or multiple bit pass */
+static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn,
+ uint32_t write_group, uint32_t use_dm, uint32_t all_correct,
+ uint32_t *bit_chk, uint32_t all_ranks)
+{
+ uint32_t r;
+ uint32_t correct_mask_vg;
+ uint32_t tmp_bit_chk;
+ uint32_t vg;
+ uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS :
+ (rank_bgn + NUM_RANKS_PER_SHADOW_REG);
+ uint32_t addr_rw_mgr;
+ uint32_t base_rw_mgr;
+
+ *bit_chk = param->write_correct_mask;
+ correct_mask_vg = param->write_correct_mask_vg;
+
+ for (r = rank_bgn; r < rank_end; r++) {
+ if (param->skip_ranks[r]) {
+ /* request to skip the rank */
+ continue;
+ }
+
+ /* set rank */
+ set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE);
+
+ tmp_bit_chk = 0;
+ addr_rw_mgr = SDR_PHYGRP_RWMGRGRP_ADDRESS;
+ for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS-1; ; vg--) {
+ /* reset the fifos to get pointers to known state */
+ writel(0, &phy_mgr_cmd->fifo_reset);
+
+ tmp_bit_chk = tmp_bit_chk <<
+ (RW_MGR_MEM_DQ_PER_WRITE_DQS /
+ RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS);
+ rw_mgr_mem_calibrate_write_test_issue(write_group *
+ RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS+vg,
+ use_dm);
+
+ base_rw_mgr = readl(addr_rw_mgr);
+ tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr));
+ if (vg == 0)
+ break;
+ }
+ *bit_chk &= tmp_bit_chk;
+ }
+
+ if (all_correct) {
+ set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
+ debug_cond(DLEVEL == 2, "write_test(%u,%u,ALL) : %u == \
+ %u => %lu", write_group, use_dm,
+ *bit_chk, param->write_correct_mask,
+ (long unsigned int)(*bit_chk ==
+ param->write_correct_mask));
+ return *bit_chk == param->write_correct_mask;
+ } else {
+ set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
+ debug_cond(DLEVEL == 2, "write_test(%u,%u,ONE) : %u != ",
+ write_group, use_dm, *bit_chk);
+ debug_cond(DLEVEL == 2, "%lu" " => %lu", (long unsigned int)0,
+ (long unsigned int)(*bit_chk != 0));
+ return *bit_chk != 0x00;
+ }
+}
+
/**
* rw_mgr_mem_calibrate_read_test_patterns() - Read back test patterns
* @rank_bgn: Rank number
@@ -2682,207 +2879,6 @@ static uint32_t rw_mgr_mem_calibrate_lfifo(void)
}
}
-/*
- * issue write test command.
- * two variants are provided. one that just tests a write pattern and
- * another that tests datamask functionality.
- */
-static void rw_mgr_mem_calibrate_write_test_issue(uint32_t group,
- uint32_t test_dm)
-{
- uint32_t mcc_instruction;
- uint32_t quick_write_mode = (((STATIC_CALIB_STEPS) & CALIB_SKIP_WRITES) &&
- ENABLE_SUPER_QUICK_CALIBRATION);
- uint32_t rw_wl_nop_cycles;
- uint32_t addr;
-
- /*
- * Set counter and jump addresses for the right
- * number of NOP cycles.
- * The number of supported NOP cycles can range from -1 to infinity
- * Three different cases are handled:
- *
- * 1. For a number of NOP cycles greater than 0, the RW Mgr looping
- * mechanism will be used to insert the right number of NOPs
- *
- * 2. For a number of NOP cycles equals to 0, the micro-instruction
- * issuing the write command will jump straight to the
- * micro-instruction that turns on DQS (for DDRx), or outputs write
- * data (for RLD), skipping
- * the NOP micro-instruction all together
- *
- * 3. A number of NOP cycles equal to -1 indicates that DQS must be
- * turned on in the same micro-instruction that issues the write
- * command. Then we need
- * to directly jump to the micro-instruction that sends out the data
- *
- * NOTE: Implementing this mechanism uses 2 RW Mgr jump-counters
- * (2 and 3). One jump-counter (0) is used to perform multiple
- * write-read operations.
- * one counter left to issue this command in "multiple-group" mode
- */
-
- rw_wl_nop_cycles = gbl->rw_wl_nop_cycles;
-
- if (rw_wl_nop_cycles == -1) {
- /*
- * CNTR 2 - We want to execute the special write operation that
- * turns on DQS right away and then skip directly to the
- * instruction that sends out the data. We set the counter to a
- * large number so that the jump is always taken.
- */
- writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
-
- /* CNTR 3 - Not used */
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- } else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0_WL_1;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_DATA,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- }
- } else if (rw_wl_nop_cycles == 0) {
- /*
- * CNTR 2 - We want to skip the NOP operation and go straight
- * to the DQS enable instruction. We set the counter to a large
- * number so that the jump is always taken.
- */
- writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
-
- /* CNTR 3 - Not used */
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- } else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_DQS,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- }
- } else {
- /*
- * CNTR 2 - In this case we want to execute the next instruction
- * and NOT take the jump. So we set the counter to 0. The jump
- * address doesn't count.
- */
- writel(0x0, &sdr_rw_load_mgr_regs->load_cntr2);
- writel(0x0, &sdr_rw_load_jump_mgr_regs->load_jump_add2);
-
- /*
- * CNTR 3 - Set the nop counter to the number of cycles we
- * need to loop for, minus 1.
- */
- writel(rw_wl_nop_cycles - 1, &sdr_rw_load_mgr_regs->load_cntr3);
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- } else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- }
- }
-
- writel(0, SDR_PHYGRP_RWMGRGRP_ADDRESS |
- RW_MGR_RESET_READ_DATAPATH_OFFSET);
-
- if (quick_write_mode)
- writel(0x08, &sdr_rw_load_mgr_regs->load_cntr0);
- else
- writel(0x40, &sdr_rw_load_mgr_regs->load_cntr0);
-
- writel(mcc_instruction, &sdr_rw_load_jump_mgr_regs->load_jump_add0);
-
- /*
- * CNTR 1 - This is used to ensure enough time elapses
- * for read data to come back.
- */
- writel(0x30, &sdr_rw_load_mgr_regs->load_cntr1);
-
- if (test_dm) {
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- } else {
- writel(RW_MGR_LFSR_WR_RD_BANK_0_WAIT,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- }
-
- addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_SINGLE_GROUP_OFFSET;
- writel(mcc_instruction, addr + (group << 2));
-}
-
-/* Test writes, can check for a single bit pass or multiple bit pass */
-static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn,
- uint32_t write_group, uint32_t use_dm, uint32_t all_correct,
- uint32_t *bit_chk, uint32_t all_ranks)
-{
- uint32_t r;
- uint32_t correct_mask_vg;
- uint32_t tmp_bit_chk;
- uint32_t vg;
- uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS :
- (rank_bgn + NUM_RANKS_PER_SHADOW_REG);
- uint32_t addr_rw_mgr;
- uint32_t base_rw_mgr;
-
- *bit_chk = param->write_correct_mask;
- correct_mask_vg = param->write_correct_mask_vg;
-
- for (r = rank_bgn; r < rank_end; r++) {
- if (param->skip_ranks[r]) {
- /* request to skip the rank */
- continue;
- }
-
- /* set rank */
- set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE);
-
- tmp_bit_chk = 0;
- addr_rw_mgr = SDR_PHYGRP_RWMGRGRP_ADDRESS;
- for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS-1; ; vg--) {
- /* reset the fifos to get pointers to known state */
- writel(0, &phy_mgr_cmd->fifo_reset);
-
- tmp_bit_chk = tmp_bit_chk <<
- (RW_MGR_MEM_DQ_PER_WRITE_DQS /
- RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS);
- rw_mgr_mem_calibrate_write_test_issue(write_group *
- RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS+vg,
- use_dm);
-
- base_rw_mgr = readl(addr_rw_mgr);
- tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr));
- if (vg == 0)
- break;
- }
- *bit_chk &= tmp_bit_chk;
- }
-
- if (all_correct) {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "write_test(%u,%u,ALL) : %u == \
- %u => %lu", write_group, use_dm,
- *bit_chk, param->write_correct_mask,
- (long unsigned int)(*bit_chk ==
- param->write_correct_mask));
- return *bit_chk == param->write_correct_mask;
- } else {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "write_test(%u,%u,ONE) : %u != ",
- write_group, use_dm, *bit_chk);
- debug_cond(DLEVEL == 2, "%lu" " => %lu", (long unsigned int)0,
- (long unsigned int)(*bit_chk != 0));
- return *bit_chk != 0x00;
- }
-}
-
/**
* search_window() - Search for the/part of the window with DM/DQS shift
* @search_dm: If 1, search for the DM shift, if 0, search for DQS shift
--
2.1.4
More information about the U-Boot
mailing list