[U-Boot] [PATCH v3 0/8] Add support for hi6220 SoC and HiKey 96boards CE board.

Peter Griffin peter.griffin at linaro.org
Wed Jul 29 23:39:28 CEST 2015


Hi Albert,

This series adds support for the first 96boards consumer edition HiKey board.

More information can be found about this board at the following link
https://www.96boards.org/products/hikey/.

This initial port adds support for: -
1) Serial
2) eMMC and sd card
3) USB
4) GPIO

It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.

Some instructions on exactly how to compile everything (l-loader,
with Arm Trusted Firmware, which then loads u-boot) is documented in the README found
in the board/hisilicon/hikey directory.

A basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf

Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
96Boards-Hikey-Rev-A1.pdf

A rather pleasant side effect of rebasing to v2015.07-rc2 is that the two main bugs
with the v1 series (that I new about at least) are resolved. DHCP now works correctly,
and USB mass storage devices are also enumerated).

The plan is once basic support is merged to u-boot, and upstream Linux kernel has DT
which supports GPIO, UART and MMC, we can migrate this u-boot port over to using DT
for configuration.

Changes since v2:
- errno.h should go above malloc.h (Simon)
- drop #ifdef CONFIG_DM_GPIO and add TODO (Simon)
- remove gd->flags = 0; (Simon)
- Remove icache_enable() (Simon / Rob)

- Added a pinmux driver for hi6220 (Simon)
- Added a pmic driver for hi6553 (Simon)
- Convert to structs for register I/O (Simon)
- Remove () around simple constants (Simon)

- Update default bootcmd (Rob)
- user kernel_addr_r etc in default env (Rob)
- Various typo's (Rob)
- use board_usb_init() to configure phy/clocks (Rob)
- Remove some more unnecessary CONFIG_FS* options (Rob)
- Update default kernel load address (Rob)
- Update default kernel cmdline (Rob)

Changes since v1:
- Rename vendor to hisilicon not 96boards (Rob)
- Get rid of aemv8a vexpress leftover (Rob)
- Remove __weak on misc_init_r (Rob)
- Remove unnecessary LINUX_BOOT_PARAM_ADDR (Rob)
- COUNTER_FREQUENCY in decimal to avoid comment (Rob)
- Remove leftover V2M* from vexpress (Rob)
- Migrate configs/hikey.h over to use config_distro_defaults.h (Rob)
- Remove custom u-boot prompt (Rob)
- Enable icache
- Remove custom delay function, as mdelay/udelay work fine (Rob)
- Update CONFIG_SYS_LOAD_ADDR to 0x80000 (Rob)

- Use suggested macro for declaring gpio addresses (Marek)
- Zap dead Macros (Marek)
- Use calloc instead of malloc (Marek)

- Reduce PHYS_RAM by 16Mb to accomodate OPTEE in latest ATF code (Peter)
- Rebase on v2015.07-rc2 (Peter)
- Add CONFIG_NET=y so that env callbacks work (Peter)

- Add a README on how to build / flash u-boot (Simon)


kind regards,

Peter.


Peter Griffin (8):
  usb: dwc2: Call board_usb_init() from usb_lowlevel_init()
  dm: gpio: hi6220: Add a hi6220 GPIO driver model driver.
  ARM: hi6220: Add register and bitfield definition header files.
  hisilicon: hi6220: Add a hi6220 pinmux driver.
  pmic: pmic_hi6553: Add a driver for the hi6553 pmic found on hikey
    board.
  mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.
  ARM64: hikey: hi6220: Add u-boot support for the 96boards CE HiKey
    board.
  ARM64: hikey: Add a README for this board.

 arch/arm/Kconfig                                   |   8 +
 arch/arm/cpu/armv8/Makefile                        |   1 +
 arch/arm/cpu/armv8/hisilicon/Makefile              |   9 +
 arch/arm/cpu/armv8/hisilicon/pinmux.c              | 184 +++++++++
 arch/arm/include/asm/arch-hi6220/dwmmc.h           |   8 +
 arch/arm/include/asm/arch-hi6220/gpio.h            |  29 ++
 arch/arm/include/asm/arch-hi6220/hi6220.h          | 387 +++++++++++++++++++
 .../include/asm/arch-hi6220/hi6220_regs_alwayson.h | 420 +++++++++++++++++++++
 arch/arm/include/asm/arch-hi6220/periph.h          |  30 ++
 arch/arm/include/asm/arch-hi6220/pinmux.h          |  83 ++++
 board/hisilicon/hikey/Kconfig                      |  15 +
 board/hisilicon/hikey/Makefile                     |   8 +
 board/hisilicon/hikey/README                       | 160 ++++++++
 board/hisilicon/hikey/hikey.c                      | 356 +++++++++++++++++
 configs/hikey_defconfig                            |   5 +
 drivers/gpio/Makefile                              |   2 +
 drivers/gpio/hi6220_gpio.c                         |  95 +++++
 drivers/mmc/Makefile                               |   1 +
 drivers/mmc/hi6220_dw_mmc.c                        |  56 +++
 drivers/power/pmic/Makefile                        |   1 +
 drivers/power/pmic/pmic_hi6553.c                   | 133 +++++++
 drivers/usb/host/dwc2.c                            |   4 +
 include/configs/hikey.h                            | 159 ++++++++
 include/power/hi6553_pmic.h                        |  79 ++++
 24 files changed, 2233 insertions(+)
 create mode 100644 arch/arm/cpu/armv8/hisilicon/Makefile
 create mode 100644 arch/arm/cpu/armv8/hisilicon/pinmux.c
 create mode 100644 arch/arm/include/asm/arch-hi6220/dwmmc.h
 create mode 100644 arch/arm/include/asm/arch-hi6220/gpio.h
 create mode 100644 arch/arm/include/asm/arch-hi6220/hi6220.h
 create mode 100644 arch/arm/include/asm/arch-hi6220/hi6220_regs_alwayson.h
 create mode 100644 arch/arm/include/asm/arch-hi6220/periph.h
 create mode 100644 arch/arm/include/asm/arch-hi6220/pinmux.h
 create mode 100644 board/hisilicon/hikey/Kconfig
 create mode 100644 board/hisilicon/hikey/Makefile
 create mode 100644 board/hisilicon/hikey/README
 create mode 100644 board/hisilicon/hikey/hikey.c
 create mode 100644 configs/hikey_defconfig
 create mode 100644 drivers/gpio/hi6220_gpio.c
 create mode 100644 drivers/mmc/hi6220_dw_mmc.c
 create mode 100644 drivers/power/pmic/pmic_hi6553.c
 create mode 100644 include/configs/hikey.h
 create mode 100644 include/power/hi6553_pmic.h

-- 
1.9.1



More information about the U-Boot mailing list