[U-Boot] [PATCH] sunxi: Add new Mele_A1000G_quad defconfig
Hans de Goede
hdegoede at redhat.com
Mon Jun 1 17:01:57 CEST 2015
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been
using the same defconfig (and dts on the kernel side) for both models.
Unfortunately this does not work for the otg controller, on the M9 this
is routed to a micro-usb connector on the outside, while as on the
A1000G-quad it is connected to an usb to sata bridge.
This commit adds a new defconfig for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun6i-a31-a1000g-quad.dts | 149 +++++++++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 1 +
configs/Mele_A1000G_quad_defconfig | 24 ++++++
configs/Mele_M9_defconfig | 10 +++
5 files changed, 185 insertions(+)
create mode 100644 arch/arm/dts/sun6i-a31-a1000g-quad.dts
create mode 100644 configs/Mele_A1000G_quad_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 267fd17..acbd9b4 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -90,6 +90,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-tzx-q8-713b7.dtb \
sun5i-a13-utoo-p66.dtb
dtb-$(CONFIG_MACH_SUN6I) += \
+ sun6i-a31-a1000g-quad.dtb \
sun6i-a31-app4-evb1.dtb \
sun6i-a31-colombus.dtb \
sun6i-a31-hummingbird.dtb \
diff --git a/arch/arm/dts/sun6i-a31-a1000g-quad.dts b/arch/arm/dts/sun6i-a31-a1000g-quad.dts
new file mode 100644
index 0000000..4404f37
--- /dev/null
+++ b/arch/arm/dts/sun6i-a31-a1000g-quad.dts
@@ -0,0 +1,149 @@
+/*
+ * Copyright 2014 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Mele A1000G Quad top set box";
+ compatible = "mele,a1000g-quad", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_m9>;
+
+ blue {
+ label = "m9:blue:usr";
+ gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ led_pins_m9: led_pins at 0 {
+ allwinner,pins = "PH13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_m9: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_m9: usb1_vbus_pin at 0 {
+ allwinner,pins = "PC27";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_m9>;
+ gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 22d560a..0618ec8 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -10,6 +10,7 @@ F: configs/Cubieboard_defconfig
F: configs/Hyundai_A7HD_defconfig
F: configs/jesurun_q5_defconfig
F: configs/Mele_A1000_defconfig
+F: configs/Mele_A1000G_quad_defconfig
F: configs/Mele_M3_defconfig
F: configs/Mini-X_defconfig
F: configs/mk802_defconfig
diff --git a/configs/Mele_A1000G_quad_defconfig b/configs/Mele_A1000G_quad_defconfig
new file mode 100644
index 0000000..b93dcf5
--- /dev/null
+++ b/configs/Mele_A1000G_quad_defconfig
@@ -0,0 +1,24 @@
+# The Mele A1000G quad is yet another Allwinnner based Android top set box
+# from Mele.
+#
+# It uses the same case as the original Mele A1000 and the same PCB as the M9,
+# the USM sata storage slot is connected via anusb to sata bridge connected to
+# the otg controller, this renders the micro USB B receptacle non functional.
+#
+# It features an A31 SoC, 2G RAM, 16G Nand, 100Mbit ethernet, HDMI out,
+# 3 USB A receptacles, 3.5 mm jack for analog audio out, optical spdif,
+# RTL R8188EU (USB) wifi and a full size sdcard slot
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_ZQ=120
+CONFIG_USB1_VBUS_PIN="PC27"
+CONFIG_USB2_VBUS_PIN=""
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-a1000g-quad"
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_AXP221_DCDC1_VOLT=3300
+CONFIG_AXP221_DLDO1_VOLT=3300
+CONFIG_AXP221_DLDO4_VOLT=3300
+CONFIG_AXP221_ALDO1_VOLT=3300
diff --git a/configs/Mele_M9_defconfig b/configs/Mele_M9_defconfig
index 4708133..16881fa 100644
--- a/configs/Mele_M9_defconfig
+++ b/configs/Mele_M9_defconfig
@@ -1,3 +1,13 @@
+# The Mele M9 is yet another Allwinnner based Android top set box from Mele.
+#
+# It uses the same PCB as the A1000G quad, but in a new case without a
+# USM sata storage slot, and the space on the PCB for the usb to sata
+# bridge connected to the otg controller is not populated, possible
+# making the micro usb otg connector functional (untested)
+#
+# It features an A31 SoC, 2G RAM, 16G Nand, 100Mbit ethernet, HDMI out,
+# 3 USB A receptacles, 3.5 mm jack for analog audio out, optical spdif,
+# micro USB B receptacle, RTL R8188EU (USB) and a full size sdcard slot
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
--
2.4.2
More information about the U-Boot
mailing list