[U-Boot] [PATCH 7/8] imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board support
Peng Fan
b51431 at freescale.com
Wed Jun 10 12:17:35 CEST 2015
Hi, Stefano
On Wed, Jun 10, 2015 at 11:40:38AM +0200, Stefano Babic wrote:
>Hi Peng,
>
>On 10/06/2015 10:06, Peng Fan wrote:
>> 1. Add DDR script for mx6qpsabreauto board.
>> 2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
>> and init the enet pll output to 125Mhz.
>> 3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
>>
>> Build target: mx6qpsabreauto_config
>>
>> U-Boot 2015.07-rc2-00008-g594f506 (Jun 10 2015 - 16:01:36 +0800)
>>
>> Boot Log:
>> CPU: Freescale i.MX6Q rev2.0 996 MHz (running at 792 MHz)
>> CPU: Automotive temperature grade (-40C to 125C) at 36C
>> Reset cause: POR
>> Board: MX6Q-Sabreauto revA
>> I2C: ready
>> DRAM: 2 GiB
>> PMIC: PFUZE100 ID=0x10
>> Flash: 32 MiB
>> NAND: 4096 MiB
>> MMC: FSL_SDHC: 0
>> *** Warning - bad CRC, using default environment
>>
>> No panel detected: default to HDMI
>> Display: HDMI (1024x768)
>> In: serial
>> Out: serial
>> Err: serial
>> Net: FEC [PRIME]
>> Error: FEC address not set.
>>
>> Hit any key to stop autoboot: 0
>>
>> Signed-off-by: Robin Gong <b38343 at freescale.com>
>> Signed-off-by: Ye.Li <B37916 at freescale.com>
>> Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
>> ---
>> board/freescale/mx6qsabreauto/mx6qp.cfg | 158 ++++++++++++++++++++++++++
>> board/freescale/mx6qsabreauto/mx6qsabreauto.c | 32 +++++-
>> configs/mx6qpsabreauto_defconfig | 5 +
>> include/configs/mx6qsabreauto.h | 5 +-
>> 4 files changed, 194 insertions(+), 6 deletions(-)
>> create mode 100644 board/freescale/mx6qsabreauto/mx6qp.cfg
>> create mode 100644 configs/mx6qpsabreauto_defconfig
>>
>> diff --git a/board/freescale/mx6qsabreauto/mx6qp.cfg b/board/freescale/mx6qsabreauto/mx6qp.cfg
>> new file mode 100644
>> index 0000000..5d55bcc
>> --- /dev/null
>> +++ b/board/freescale/mx6qsabreauto/mx6qp.cfg
>> @@ -0,0 +1,158 @@
>> +/*
>> + * Copyright (C) 2015 Freescale Semiconductor, Inc.
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + *
>> + * Refer doc/README.imximage for more details about how-to configure
>> + * and create imximage boot image
>> + *
>> + * The syntax is taken as close as possible with the kwbimage
>> + */
>> +/* image version */
>> +
>> +#define __ASSEMBLY__
>> +#include <config.h>
>> +
>> +IMAGE_VERSION 2
>> +
>> +/*
>> + * Boot Device : one of spi, sd, eimnor, nand, sata:
>> + * spinor: flash_offset: 0x0400
>> + * nand: flash_offset: 0x0400
>> + * sata: flash_offset: 0x0400
>> + * sd/mmc: flash_offset: 0x0400
>> + * eimnor: flash_offset: 0x1000
>> + */
>> +
>> +#if defined(CONFIG_SYS_BOOT_EIMNOR)
>
>
>?????
Will remove this in v2.
>
>Not defined in U-Boot mainline.
>
>> +BOOT_FROM nor
>> +#else /* others has the same flash_offset as sd */
>> +BOOT_FROM sd
>> +#endif
>> +
>> +#ifdef CONFIG_USE_PLUGIN
>> +/*PLUGIN plugin-binary-file IRAM_FREE_START_ADDR*/
>> +PLUGIN board/freescale/mx6qsabreauto/plugin.bin 0x00907000
>
>Ditto,
Will remove this in v2.
>
>> +#else
>> +
>> +#ifdef CONFIG_SECURE_BOOT
>> +CSF 0x2000
>> +#endif
>> +
>> +/*
>> + * Device Configuration Data (DCD)
>> + *
>> + * Each entry must have the format:
>> + * Addr-type Address Value
>> + *
>> + * where:
>> + * Addr-type register length (1,2 or 4 bytes)
>> + * Address absolute address of the register
>> + * value value to be stored in the register
>> + */
>> +DATA 4 0x020e0798 0x000C0000
>> +DATA 4 0x020e0758 0x00000000
>> +DATA 4 0x020e0588 0x00000030
>> +DATA 4 0x020e0594 0x00000030
>> +DATA 4 0x020e056c 0x00000030
>> +DATA 4 0x020e0578 0x00000030
>> +DATA 4 0x020e074c 0x00000030
>> +DATA 4 0x020e057c 0x00000030
>> +DATA 4 0x020e058c 0x00000000
>> +DATA 4 0x020e059c 0x00000030
>> +DATA 4 0x020e05a0 0x00000030
>> +DATA 4 0x020e078c 0x00000030
>> +DATA 4 0x020e0750 0x00020000
>
>Until here, the same as mx6qsabreauto
>
>
>> +DATA 4 0x020e05a8 0x00000030
>> +DATA 4 0x020e05b0 0x00000030
>> +DATA 4 0x020e0524 0x00000030
>> +DATA 4 0x020e051c 0x00000030
>> +DATA 4 0x020e0518 0x00000030
>> +DATA 4 0x020e050c 0x00000030
>> +DATA 4 0x020e05b8 0x00000030
>> +DATA 4 0x020e05c0 0x00000030
>
>Here is 40 ohm (reset value, do you need to set it ?) instead of 48 ohm
>as on 6qauto. Anyway, is there some chance to add SPL support for this
>board ? DDR setup can be then managed inside SPL code dropping this part
>and a single image for sabreauto6q and sabreauto6qp could be possible.
>
We get the script from IC team, so there maybe many duplicated configuration.
I get your concern that SPL can give many benifits.
Current, we do not have plan to add SPL support.
>Of course, I will not block the patchset if this is not planned, but
>maybe you can consider it. In any case, some factorizing must be done
>instead of duplicating the cfg code.
Using SPL, we can remove duplicated ddr cfg, but using cfg file, not that easy.
I'll try.
>
>> +DATA 4 0x020e0774 0x00020000
>> +DATA 4 0x020e0784 0x00000030
>> +DATA 4 0x020e0788 0x00000030
>> +DATA 4 0x020e0794 0x00000030
>> +DATA 4 0x020e079c 0x00000030
>> +DATA 4 0x020e07a0 0x00000030
>> +DATA 4 0x020e07a4 0x00000030
>> +DATA 4 0x020e07a8 0x00000030
>> +DATA 4 0x020e0748 0x00000030
>> +DATA 4 0x020e05ac 0x00000030
>> +DATA 4 0x020e05b4 0x00000030
>> +DATA 4 0x020e0528 0x00000030
>> +DATA 4 0x020e0520 0x00000030
>> +DATA 4 0x020e0514 0x00000030
>> +DATA 4 0x020e0510 0x00000030
>> +DATA 4 0x020e05bc 0x00000030
>> +DATA 4 0x020e05c4 0x00000030
>> +DATA 4 0x021b0800 0xa1390003
>> +DATA 4 0x021b080c 0x001b001e
>> +DATA 4 0x021b0810 0x002e0029
>> +DATA 4 0x021b480c 0x001b002a
>> +DATA 4 0x021b4810 0x0019002c
>> +DATA 4 0x021b083c 0x43240334
>> +DATA 4 0x021b0840 0x0324031a
>> +DATA 4 0x021b483c 0x43340344
>> +DATA 4 0x021b4840 0x03280276
>> +DATA 4 0x021b0848 0x44383A3E
>> +DATA 4 0x021b4848 0x3C3C3846
>> +DATA 4 0x021b0850 0x2e303230
>> +DATA 4 0x021b4850 0x38283E34
>
>
>
>> +DATA 4 0x021b081c 0x33333333
>> +DATA 4 0x021b0820 0x33333333
>> +DATA 4 0x021b0824 0x33333333
>> +DATA 4 0x021b0828 0x33333333
>> +DATA 4 0x021b481c 0x33333333
>> +DATA 4 0x021b4820 0x33333333
>> +DATA 4 0x021b4824 0x33333333
>> +DATA 4 0x021b4828 0x33333333
>> +DATA 4 0x021b08b8 0x00000800
>> +DATA 4 0x021b48b8 0x00000800
>> +DATA 4 0x021b0004 0x00020036
>> +DATA 4 0x021b0008 0x09444040
>> +DATA 4 0x021b000c 0x898E7955
>> +DATA 4 0x021b0010 0xFF328F64
>> +DATA 4 0x021b0014 0x01FF00DB
>> +DATA 4 0x021b0018 0x00001740
>> +DATA 4 0x021b001c 0x00008000
>> +
>
>This is also common.
>
>> +DATA 4 0x021b002c 0x000026d2
>> +DATA 4 0x021b0030 0x008E1023
>> +DATA 4 0x021b0040 0x00000047
>> +DATA 4 0x021b0400 0x12420000
>> +DATA 4 0x021b0000 0x841A0000
>> +DATA 4 0x00bb0008 0x00000004
>> +DATA 4 0x00bb000c 0x2891E41A
>> +DATA 4 0x00bb0038 0x00000564
>> +DATA 4 0x00bb0014 0x00000040
>> +DATA 4 0x00bb0028 0x00000020
>> +DATA 4 0x00bb002c 0x00000020
>> +DATA 4 0x021b001c 0x04088032
>> +DATA 4 0x021b001c 0x00008033
>> +DATA 4 0x021b001c 0x00048031
>> +DATA 4 0x021b001c 0x09408030
>> +DATA 4 0x021b001c 0x04008040
>> +DATA 4 0x021b0020 0x00005800
>> +DATA 4 0x021b0818 0x00011117
>> +DATA 4 0x021b4818 0x00011117
>> +DATA 4 0x021b0004 0x00025576
>> +DATA 4 0x021b0404 0x00011006
>> +DATA 4 0x021b001c 0x00000000
>> +/* set the default clock gate to save power */
>> +DATA 4, 0x020c4068, 0x00C03F3F
>> +DATA 4, 0x020c406c, 0x0030FC03
>> +DATA 4, 0x020c4070, 0x0FFFC000
>> +DATA 4, 0x020c4074, 0x3FF00000
>> +DATA 4, 0x020c4078, 0xFFFFF300
>> +DATA 4, 0x020c407c, 0x0F0000F3
>> +DATA 4, 0x020c4080, 0x00000FFF
>> +
>> +/* enable AXI cache for VDOA/VPU/IPU */
>> +DATA 4, 0x020e0010, 0xF00000CF
>> +/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
>> +DATA 4, 0x020e0018, 0x77177717
>> +DATA 4, 0x020e001c, 0x77177717
>> +#endif
>
>
>
>
>> diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
>> index b76e4eb..83e34c6 100644
>> --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
>> +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
>> @@ -354,9 +354,27 @@ int board_phy_config(struct phy_device *phydev)
>> return 0;
>> }
>>
>> +static int setup_fec(void)
>> +{
>> + int ret;
>> +
>> +#ifdef CONFIG_MX6QP
>
>runtime detection
Will fix it in v2.
>
>> + imx_iomux_set_gpr_register(5, 9, 1, 1);
>> +#else
>> + imx_iomux_set_gpr_register(1, 21, 1, 1);
>
>For not-6qp board you change it. Can you explain why and add comments
>about what you are doing (see comment at lines 563 and following
>regarding otg).
Will fix it in v2.
>
>> +#endif
>> +
>> + ret = enable_fec_anatop_clock(ENET_125MHZ);
>> + if (ret)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> int board_eth_init(bd_t *bis)
>> {
>> setup_iomux_enet();
>> + setup_fec();
>>
>> return cpu_eth_init(bis);
>> }
>> @@ -495,17 +513,21 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
>> int power_init_board(void)
>> {
>> struct pmic *p;
>> - unsigned int ret;
>> + unsigned int value;
>>
>> p = pfuze_common_init(I2C_PMIC);
>> if (!p)
>> return -ENODEV;
>>
>> - ret = pfuze_mode_init(p, APS_PFM);
>> - if (ret < 0)
>> - return ret;
>> + if (is_mx6dqp()) {
>> + /* set SW2 staby volatage 0.975V*/
>> + pmic_reg_read(p, PFUZE100_SW2STBY, &value);
>> + value &= ~0x3f;
>> + value |= 0x17;
>> + pmic_reg_write(p, PFUZE100_SW2STBY, value);
>> + }
>>
>> - return 0;
>> + return pfuze_mode_init(p, APS_PFM);
>> }
>>
>> #ifdef CONFIG_CMD_BMODE
>> diff --git a/configs/mx6qpsabreauto_defconfig b/configs/mx6qpsabreauto_defconfig
>> new file mode 100644
>> index 0000000..e0b717a
>> --- /dev/null
>> +++ b/configs/mx6qpsabreauto_defconfig
>> @@ -0,0 +1,5 @@
>> +CONFIG_ARM=y
>> +CONFIG_TARGET_MX6QSABREAUTO=y
>> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6QP"
>> +CONFIG_CMD_SETEXPR=y
>> +CONFIG_CMD_NET=y
>> diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
>> index 2260344..6ac64e6 100644
>> --- a/include/configs/mx6qsabreauto.h
>> +++ b/include/configs/mx6qsabreauto.h
>> @@ -12,7 +12,10 @@
>> #define CONFIG_MACH_TYPE 3529
>> #define CONFIG_MXC_UART_BASE UART4_BASE
>> #define CONFIG_CONSOLE_DEV "ttymxc3"
>> -#if defined CONFIG_MX6Q
>> +
>> +#if defined CONFIG_MX6QP
>> +#define CONFIG_DEFAULT_FDT_FILE "imx6qp-sabreauto.dtb"
>> +#elif defined CONFIG_MX6Q
>> #define CONFIG_DEFAULT_FDT_FILE "imx6q-sabreauto.dtb"
>> #elif defined CONFIG_MX6DL
>> #define CONFIG_DEFAULT_FDT_FILE "imx6dl-sabreauto.dtb"
>>
>
>Best regards,
>Stefano Babic
>
>--
>=====================================================================
>DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
>HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
>=====================================================================
Regards,
Peng.
--
More information about the U-Boot
mailing list