[U-Boot] [PATCH v2 7/8] imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board support
Peng Fan
Peng.Fan at freescale.com
Thu Jun 11 12:30:41 CEST 2015
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00034-gba46bb1 (Jun 11 2015 - 16:46:41 +0800)
CPU: Freescale i.MX6Q rev2.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 26C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 4096 MiB
MMC: FSL_SDHC: 0
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Robin Gong <b38343 at freescale.com>
Signed-off-by: Ye.Li <B37916 at freescale.com>
Signed-off-by: Peng Fan <Peng.Fan at freescale.com>
---
Changes v2:
1. Remove unused macro in current upstream uboot.
2. setup_fec, remove non 6qp code. Add comments for gpr setting.
3. mx6qp.cfg is still same with v1. The settings is from IC and passed
memory ddr stress test. Since we current have no plan to add SPL,
so leave settings unchanged.
board/freescale/mx6qsabreauto/mx6qp.cfg | 143 ++++++++++++++++++++++++++
board/freescale/mx6qsabreauto/mx6qsabreauto.c | 29 ++++--
configs/mx6qpsabreauto_defconfig | 5 +
include/configs/mx6qsabreauto.h | 5 +-
4 files changed, 175 insertions(+), 7 deletions(-)
create mode 100644 board/freescale/mx6qsabreauto/mx6qp.cfg
create mode 100644 configs/mx6qpsabreauto_defconfig
diff --git a/board/freescale/mx6qsabreauto/mx6qp.cfg b/board/freescale/mx6qsabreauto/mx6qp.cfg
new file mode 100644
index 0000000..0370636
--- /dev/null
+++ b/board/freescale/mx6qsabreauto/mx6qp.cfg
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+/* image version */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of spi, sd, eimnor, nand, sata:
+ * spinor: flash_offset: 0x0400
+ * nand: flash_offset: 0x0400
+ * sata: flash_offset: 0x0400
+ * sd/mmc: flash_offset: 0x0400
+ * eimnor: flash_offset: 0x1000
+ */
+BOOT_FROM sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+DATA 4 0x020e0798 0x000C0000
+DATA 4 0x020e0758 0x00000000
+DATA 4 0x020e0588 0x00000030
+DATA 4 0x020e0594 0x00000030
+DATA 4 0x020e056c 0x00000030
+DATA 4 0x020e0578 0x00000030
+DATA 4 0x020e074c 0x00000030
+DATA 4 0x020e057c 0x00000030
+DATA 4 0x020e058c 0x00000000
+DATA 4 0x020e059c 0x00000030
+DATA 4 0x020e05a0 0x00000030
+DATA 4 0x020e078c 0x00000030
+DATA 4 0x020e0750 0x00020000
+DATA 4 0x020e05a8 0x00000030
+DATA 4 0x020e05b0 0x00000030
+DATA 4 0x020e0524 0x00000030
+DATA 4 0x020e051c 0x00000030
+DATA 4 0x020e0518 0x00000030
+DATA 4 0x020e050c 0x00000030
+DATA 4 0x020e05b8 0x00000030
+DATA 4 0x020e05c0 0x00000030
+DATA 4 0x020e0774 0x00020000
+DATA 4 0x020e0784 0x00000030
+DATA 4 0x020e0788 0x00000030
+DATA 4 0x020e0794 0x00000030
+DATA 4 0x020e079c 0x00000030
+DATA 4 0x020e07a0 0x00000030
+DATA 4 0x020e07a4 0x00000030
+DATA 4 0x020e07a8 0x00000030
+DATA 4 0x020e0748 0x00000030
+DATA 4 0x020e05ac 0x00000030
+DATA 4 0x020e05b4 0x00000030
+DATA 4 0x020e0528 0x00000030
+DATA 4 0x020e0520 0x00000030
+DATA 4 0x020e0514 0x00000030
+DATA 4 0x020e0510 0x00000030
+DATA 4 0x020e05bc 0x00000030
+DATA 4 0x020e05c4 0x00000030
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b080c 0x001b001e
+DATA 4 0x021b0810 0x002e0029
+DATA 4 0x021b480c 0x001b002a
+DATA 4 0x021b4810 0x0019002c
+DATA 4 0x021b083c 0x43240334
+DATA 4 0x021b0840 0x0324031a
+DATA 4 0x021b483c 0x43340344
+DATA 4 0x021b4840 0x03280276
+DATA 4 0x021b0848 0x44383A3E
+DATA 4 0x021b4848 0x3C3C3846
+DATA 4 0x021b0850 0x2e303230
+DATA 4 0x021b4850 0x38283E34
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+DATA 4 0x021b481c 0x33333333
+DATA 4 0x021b4820 0x33333333
+DATA 4 0x021b4824 0x33333333
+DATA 4 0x021b4828 0x33333333
+DATA 4 0x021b08b8 0x00000800
+DATA 4 0x021b48b8 0x00000800
+DATA 4 0x021b0004 0x00020036
+DATA 4 0x021b0008 0x09444040
+DATA 4 0x021b000c 0x898E7955
+DATA 4 0x021b0010 0xFF328F64
+DATA 4 0x021b0014 0x01FF00DB
+DATA 4 0x021b0018 0x00001740
+DATA 4 0x021b001c 0x00008000
+
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x008E1023
+DATA 4 0x021b0040 0x00000047
+DATA 4 0x021b0400 0x12420000
+DATA 4 0x021b0000 0x841A0000
+DATA 4 0x00bb0008 0x00000004
+DATA 4 0x00bb000c 0x2891E41A
+DATA 4 0x00bb0038 0x00000564
+DATA 4 0x00bb0014 0x00000040
+DATA 4 0x00bb0028 0x00000020
+DATA 4 0x00bb002c 0x00000020
+DATA 4 0x021b001c 0x04088032
+DATA 4 0x021b001c 0x00008033
+DATA 4 0x021b001c 0x00048031
+DATA 4 0x021b001c 0x09408030
+DATA 4 0x021b001c 0x04008040
+DATA 4 0x021b0020 0x00005800
+DATA 4 0x021b0818 0x00011117
+DATA 4 0x021b4818 0x00011117
+DATA 4 0x021b0004 0x00025576
+DATA 4 0x021b0404 0x00011006
+DATA 4 0x021b001c 0x00000000
+/* set the default clock gate to save power */
+DATA 4, 0x020c4068, 0x00C03F3F
+DATA 4, 0x020c406c, 0x0030FC03
+DATA 4, 0x020c4070, 0x0FFFC000
+DATA 4, 0x020c4074, 0x3FF00000
+DATA 4, 0x020c4078, 0xFFFFF300
+DATA 4, 0x020c407c, 0x0F0000F3
+DATA 4, 0x020c4080, 0x00000FFF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, 0x020e0010, 0xF00000CF
+/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
+DATA 4, 0x020e0018, 0x77177717
+DATA 4, 0x020e001c, 0x77177717
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index b76e4eb..ab7d018 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -354,9 +354,22 @@ int board_phy_config(struct phy_device *phydev)
return 0;
}
-int board_eth_init(bd_t *bis)
+static void setup_fec(void)
{
+ if (is_mx6dqp()) {
+ /*
+ * select ENET MAC0 TX clock from PLL
+ */
+ imx_iomux_set_gpr_register(5, 9, 1, 1);
+ enable_fec_anatop_clock(ENET_125MHZ);
+ }
+
setup_iomux_enet();
+}
+
+int board_eth_init(bd_t *bis)
+{
+ setup_fec();
return cpu_eth_init(bis);
}
@@ -495,17 +508,21 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
int power_init_board(void)
{
struct pmic *p;
- unsigned int ret;
+ unsigned int value;
p = pfuze_common_init(I2C_PMIC);
if (!p)
return -ENODEV;
- ret = pfuze_mode_init(p, APS_PFM);
- if (ret < 0)
- return ret;
+ if (is_mx6dqp()) {
+ /* set SW2 staby volatage 0.975V*/
+ pmic_reg_read(p, PFUZE100_SW2STBY, &value);
+ value &= ~0x3f;
+ value |= 0x17;
+ pmic_reg_write(p, PFUZE100_SW2STBY, value);
+ }
- return 0;
+ return pfuze_mode_init(p, APS_PFM);
}
#ifdef CONFIG_CMD_BMODE
diff --git a/configs/mx6qpsabreauto_defconfig b/configs/mx6qpsabreauto_defconfig
new file mode 100644
index 0000000..0ad23cf
--- /dev/null
+++ b/configs/mx6qpsabreauto_defconfig
@@ -0,0 +1,5 @@
+CONFIG_ARM=y
+CONFIG_TARGET_MX6QSABREAUTO=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6qp.cfg,MX6QP"
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_NET=y
diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index 2260344..6ac64e6 100644
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -12,7 +12,10 @@
#define CONFIG_MACH_TYPE 3529
#define CONFIG_MXC_UART_BASE UART4_BASE
#define CONFIG_CONSOLE_DEV "ttymxc3"
-#if defined CONFIG_MX6Q
+
+#if defined CONFIG_MX6QP
+#define CONFIG_DEFAULT_FDT_FILE "imx6qp-sabreauto.dtb"
+#elif defined CONFIG_MX6Q
#define CONFIG_DEFAULT_FDT_FILE "imx6q-sabreauto.dtb"
#elif defined CONFIG_MX6DL
#define CONFIG_DEFAULT_FDT_FILE "imx6dl-sabreauto.dtb"
--
1.8.4
More information about the U-Boot
mailing list