[U-Boot] [PATCH 16/22] sunxi: usb-phy: Add support for reading otg id pin value

[Hans de Goede]

Add support for reading the id pin value of the otg connector to the usb
phy code.

Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
 arch/arm/cpu/armv7/sunxi/usb_phy.c        | 34 +++++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-sunxi/usb_phy.h |  1 +
 board/sunxi/Kconfig                       |  7 +++++++
 3 files changed, 42 insertions(+)

diff --git a/arch/arm/cpu/armv7/sunxi/usb_phy.c b/arch/arm/cpu/armv7/sunxi/usb_phy.c
index b07d67f..5e82ddc 100644
--- a/arch/arm/cpu/armv7/sunxi/usb_phy.c
+++ b/arch/arm/cpu/armv7/sunxi/usb_phy.c
@@ -44,6 +44,7 @@ static struct sunxi_usb_phy {
 	int usb_rst_mask;
 	int gpio_vbus;
 	int gpio_vbus_det;
+	int gpio_id_det;
 	int id;
 	int init_count;
 	int power_on_count;
@@ -82,6 +83,14 @@ static int get_vbus_detect_gpio(int index)
 	return -EINVAL;
 }
 
+static int get_id_detect_gpio(int index)
+{
+	switch (index) {
+	case 0: return sunxi_name_to_gpio(CONFIG_USB0_ID_DET);
+	}
+	return -EINVAL;
+}
+
 static void usb_phy_write(struct sunxi_usb_phy *phy, int addr,
 			  int data, int len)
 {
@@ -247,6 +256,16 @@ int sunxi_usb_phy_vbus_detect(int index)
 	return err;
 }
 
+int sunxi_usb_phy_id_detect(int index)
+{
+	struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+
+	if (phy->gpio_id_det < 0)
+		return phy->gpio_id_det;
+
+	return gpio_get_value(phy->gpio_id_det);
+}
+
 int sunxi_usb_phy_probe(void)
 {
 	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
@@ -275,6 +294,18 @@ int sunxi_usb_phy_probe(void)
 			if (ret)
 				return ret;
 		}
+
+		phy->gpio_id_det = get_id_detect_gpio(i);
+		if (phy->gpio_id_det >= 0) {
+			ret = gpio_request(phy->gpio_id_det, "usb_id_det");
+			if (ret)
+				return ret;
+			ret = gpio_direction_input(phy->gpio_id_det);
+			if (ret)
+				return ret;
+			sunxi_gpio_set_pull(phy->gpio_id_det,
+					    SUNXI_GPIO_PULL_UP);
+		}
 	}
 
 	setbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
@@ -298,6 +329,9 @@ int sunxi_usb_phy_remove(void)
 
 		if (phy->gpio_vbus_det >= 0)
 			gpio_free(phy->gpio_vbus_det);
+
+		if (phy->gpio_id_det >= 0)
+			gpio_free(phy->gpio_id_det);
 	}
 
 	return 0;
diff --git a/arch/arm/include/asm/arch-sunxi/usb_phy.h b/arch/arm/include/asm/arch-sunxi/usb_phy.h
index b7b831e..5a9cacb 100644
--- a/arch/arm/include/asm/arch-sunxi/usb_phy.h
+++ b/arch/arm/include/asm/arch-sunxi/usb_phy.h
@@ -17,4 +17,5 @@ void sunxi_usb_phy_exit(int index);
 void sunxi_usb_phy_power_on(int index);
 void sunxi_usb_phy_power_off(int index);
 int sunxi_usb_phy_vbus_detect(int index);
+int sunxi_usb_phy_id_detect(int index);
 void sunxi_usb_phy_enable_squelch_detect(int index, int enable);
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index b2eca51..4311c3e 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -306,6 +306,13 @@ config USB0_VBUS_DET
 	Set the Vbus detect pin for usb0 (otg). This takes a string in the
 	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
 
+config USB0_ID_DET
+	string "ID detect pin for usb0 (otg)"
+	default ""
+	---help---
+	Set the ID detect pin for usb0 (otg). This takes a string in the
+	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
 config USB1_VBUS_PIN
 	string "Vbus enable pin for usb1 (ehci0)"
 	default "PH6" if MACH_SUN4I || MACH_SUN7I
-- 
2.4.3