[U-Boot] [PATCH 18/22] sunxi: musb: Add id pin support

[Hans de Goede]

When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.

Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
 configs/Ippo_q8h_v1_2_a33_1024x600_defconfig | 1 +
 configs/Ippo_q8h_v1_2_defconfig              | 1 +
 configs/Ippo_q8h_v5_defconfig                | 1 +
 drivers/usb/musb-new/sunxi.c                 | 5 +++++
 4 files changed, 8 insertions(+)

diff --git a/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig b/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
index 5b1080f..51d75c9 100644
--- a/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
+++ b/configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
@@ -5,6 +5,7 @@ CONFIG_DRAM_CLK=480
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
 CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
diff --git a/configs/Ippo_q8h_v1_2_defconfig b/configs/Ippo_q8h_v1_2_defconfig
index 8d03300..20fc311 100644
--- a/configs/Ippo_q8h_v1_2_defconfig
+++ b/configs/Ippo_q8h_v1_2_defconfig
@@ -5,6 +5,7 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63306
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
 CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
diff --git a/configs/Ippo_q8h_v5_defconfig b/configs/Ippo_q8h_v5_defconfig
index 1a07064..3264a20 100644
--- a/configs/Ippo_q8h_v5_defconfig
+++ b/configs/Ippo_q8h_v5_defconfig
@@ -5,6 +5,7 @@ CONFIG_DRAM_CLK=480
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
 CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
diff --git a/drivers/usb/musb-new/sunxi.c b/drivers/usb/musb-new/sunxi.c
index ee018c7..cafb480 100644
--- a/drivers/usb/musb-new/sunxi.c
+++ b/drivers/usb/musb-new/sunxi.c
@@ -217,6 +217,11 @@ static int sunxi_musb_enable(struct musb *musb)
 			printf("A charger is plugged into the OTG: ");
 			return -ENODEV;
 		}
+		ret = sunxi_usb_phy_id_detect(0);
+		if (ret == 1) {
+			printf("No host cable detected: ");
+			return -ENODEV;
+		}
 		sunxi_usb_phy_power_on(0); /* port power on */
 	}
 
-- 
2.4.3